Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Add the timeout and timeout_char keyword options.
- Make uart.read() non-blocking.
- Add uart.any().
- Add ioctl MP_STREAM_POLL handling.
- Change uart.write() into non-busy waiting. uart.write() still waits until
all data has been sent, but calls MICROPY_EVENT_POLL_HOOK while waiting.
uart.write() uses DMA for transfer. One option would be to add a small
local buffer, such that transfers up to the size of the buffer could be
done without waiting.
- As a side effect to the change of uart.write(), uart.txdone() and ioctl
flush now report/wait correctly for the end of transmission.
- Change machine_hard_uart_buf_t in machine_hard_uart_obj_t to an instance
of that struct, rather than a pointer to one.
As the comment in py/obj.h says:
> Implementing this as a call rather than inline saves 8 bytes per usage.
So in order to get this savings, we need to tell the compiler to never
inline the function.
Signed-off-by: David Lechner <david@pybricks.com>
Even if boards do not have a clock crystal. In that case, the clock
quality will be very poor.
Always having machine.RTC means that the date/time can be set in a way that
is consistent with other ports.
This commit also removes the special code in modutime.c for devices without
the RTC class.
Signed-off-by: Damien George <damien@micropython.org>
Without this, building the unix port variants gives:
ports/unix/main.c:667: undefined reference to `mp_obj_is_package',
when MICROPY_ENABLE_EXTERNAL_IMPORT is 0.
Signed-off-by: Laurens Valk <laurens@pybricks.com>
The C-level printf is usually used for internal debugging prints, and a
port/board may want to redirect this somewhere other than stdout.
Signed-off-by: Damien George <damien@micropython.org>
These have the same frequency, but can have different duty cycle and
polarity.
pwm.deinit() stops all channels of a module, but does not release the
module. pwm.init() without arguments restarts all outputs.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.
Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
cycles.
- Limited to the P0.x pins.
Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
When := is used in a comprehension the target variable is bound to the
parent scope, so it's either a global or a nonlocal. Prior to this commit
that was handled by simply using the parent scope's id_info for the
target variable. That's completely wrong because it uses the slot number
for the parent's Python stack to store the variable, rather than the slot
number for the comprehension. This will in most cases lead to incorrect
behaviour or memory faults.
This commit fixes the scoping of the target variable by explicitly
declaring it a global or nonlocal, depending on whether the parent is the
global scope or not. Then the id_info of the comprehension can be used to
access the target variable. This fixes a lot of cases of using := in a
comprehension.
Code size change for this commit:
bare-arm: +0 +0.000%
minimal x86: +0 +0.000%
unix x64: +152 +0.019% standard
stm32: +96 +0.024% PYBV10
cc3200: +96 +0.052%
esp8266: +196 +0.028% GENERIC
esp32: +156 +0.010% GENERIC[incl +8(data)]
mimxrt: +96 +0.027% TEENSY40
renesas-ra: +88 +0.014% RA6M2_EK
nrf: +88 +0.048% pca10040
rp2: +104 +0.020% PICO
samd: +88 +0.033% ADAFRUIT_ITSYBITSY_M4_EXPRESS
Fixes issue #10895.
Signed-off-by: Damien George <damien@micropython.org>
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM. Then in main.c use these addresses as arguments to gc_init().
The benefits of this change are:
1) When libraries are added or removed in the future changing BSS usage,
main.c's sizing of the GC heap does not need to be changed.
2) Currently these changes make the GC area about 30 KBytes larger, eg on
PICO_W the GC heap increases from 166016 to 192448 bytes. Without that
change this RAM would never get used.
3) If someone wants to disable one or more SRAM blocks on the RP2040 to
reduce power consumption it will be easy: just change the MEMORY section
in memmap_mp.ld. For instance to not use SRAM2 and SRAM3 change it to:
MEMORY
{
FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
RAM(rwx) : ORIGIN = 0x21000000, LENGTH = 128k
SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
}
Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
appropriate bits in WAKE_EN0 and SLEEP_EN0.
Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info(). Confirmed GC total size approximately matched the
size calculated by the loader.
Signed-off-by: cpottle9 <cpottle9@outlook.com>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
The device-under-test should use `multitest.expect_reboot()` to indicate
that it will reboot.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
This brings in the following new modules: hs3003, bmi270, bmm150, cbor2
and senml. It also refactors lsm6dsox and lsm9ds1.
Signed-off-by: Damien George <damien@micropython.org>
