The existing qspi for stm32 implementation can only send a spi command with
exactly 0 or 2 data bytes. Certain spiflash chips (e.g. AT25SF321B) have
commands that only take a single data byte, and will ignore the command if
more than that is sent. This commit allows sending a command with a single
data byte.
Signed-off-by: Victor Rajewski <victor@allumeenergy.com.au>
For STM32G4, there is a errata on ADC that may get wrong ADC result.
According to the errata sheet, this can be avoid by performing two
consecutive ADC conversions and keep second result.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STM32G4 series, the internal sensors are connected to:
- ADC1_IN16: Temperature sensor
- ADC1_IN17: Battery voltage monitoring
- ADC1_IN18: Internal voltage reference
but ADC_CHANNEL_TEMPSENSOR_ADC1, ADC_CHANNEL_VBAT,
ADC_CHANNEL_VREFINT are not defined as 16, 17, 18.
This commit converts channel 16, 17, 18 to ADC_CHANNEL_x in
adc_get_internal_channel().
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STM32G4,
* TS_CAL1 raw data acquired at a temperature of 30°C
* TS_CAL2 raw data acquired at a temperature of 130°C
Also, these values are at VDDA=3.0V.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STM32G4, ADC clock frequency should be equal or less than 60MHz.
To satisfy this specification, ADC clock prescaler should be equal or
greater than 4 (For example, NUCLEO_G474RE runs 170MHz).
In addition, to obtain accurate internal channel value,
the ADC clock prescaler is set to 16 because vbat needs at least 12us
(16/170*247.5=23.3us).
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STMG4 MCUs, the peripheral registers for DAC have to be accessed by
words (32bits) because DAC is connected to AHB directly.
(This requirement is also there for other MCU series. However, if DAC is
connected to APB like F4/L1/L4 MCUs, AHB byte or half-word transfer is
changed into a 32-bit APB transfer. This means that PSIZE does not have to
be DMA_PDATAALIGN_WORD on these MCUs, and in fact must be BYTE/HALFWORD to
function correctly.)
Fixes issue #9563.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
This is a fix for commit bccbaa92b1fc6237f0f49a7f07cc194835fbf4e3:
- Should only wait for WIFI_EVENT_STA_START when invoked on the STA_IF
interface.
- The WIFI_EVENT_STA_START event is generated every time the STA_IF
interface is set active(True) and it was previously inactive, ie. not
only after calling esp_wifi_start().
- Also wait for WIFI_EVENT_STA_STOP when deactivating the interface.
- Also wait for relevant AP events.
Fixes issue #11910.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
This is confined to pure ASCII, but does support Alt Gr. This is enough
to make a French keyboard layout work:
* home row is "qsdfghjklm"
* numerals are all shifted
* keys like {} require Alt Gr
While not tested, this should also support layouts like Colemak with
the necssary keymap file.
Layouts can be produced from Neradoc's keyboard layout modules on the
device & loaded at runtime. Code to do so is at
https://gist.github.com/jepler/597c0a00e0eb014a433e03c0ae363a08
as well as a sketch of how an extended format could support dead keys &
the full Unicode BMP instead of just ASCII.
Enabling mDNS put this firmware over the limit of the OTA partition size,
so tweak the compiler settings to reduce the firmware size.
Signed-off-by: Damien George <damien@micropython.org>
To match the other functions in the machine module, in particular so that
MICROPY_PY_MACHINE can be disabled without getting a compiler warning about
unused code.
Signed-off-by: Damien George <damien@micropython.org>
