For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Reverse operations are supported on stm32 and rp2, and esp32 has enough
space to also enable inplace operations, to make it complete.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This enables optional support for the hardware UART to use the RTS and/or
CTS pins for flow control.
The new "flow" constructor keyword specifies a bitmask of RTS and/or CTS.
This matches the interface used by machine.UART on stm32 and rp2.
Previously on ESP32 it was possible to specify which pins to use for the
RTS and CTS signals, but hardware flow control was never functional: CTS
was not checked before transmitting bytes, and RTS was always driven high
(signalling no buffer space available). With this patch, CTS and RTS both
operate as expected.
This also includes an update to the machine.UART documentation.
Signed-off-by: Will Sowerbutts <will@sowerbutts.com>
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.
This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
hyperflash.
- minor incidental changes to other boards so they still build
Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, if the UART hardware FIFO had a few chars but still
below the FIFO trigger threshold, and the ringbuf was empty, the read
function would timeout if timeout==0 (the default timeout).
This fix follows the suggestion of @iabdalkader.
The RX IRQ does not trigger if the FIFO is less than the trigger level, in
which case characters may be available in the FIFO, yet not in the ringbuf,
and the ioctl returns false.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
This helps the OS switch to and give other threads processing time during
the sleep. It also ensures that pending events are handled, even when
sleeping for 0ms.
Fixes issue #5344.
Signed-off-by: Damien George <damien@micropython.org>
Call MICROPY_EVENT_POLL_HOOK even on very short delays so that busy loops
that call sleep_ms still yield to events and other threads.
See related issue #5344.
Replace "master" with "controller" and "slave" with "peripheral" in
comments, errors, and debug messages.
Add CONTROLLER and PERIPHERAL constants to pyb.SPI and pyb.I2C classes;
retain MASTER and SLAVE constants for backward compatiblity.
Using a 2-item transaction queue instead of 1 allows long transfers to
be executed with the minimum inter-transaction delay. Limit maximum
transaction length to ensure an integer multiple of the SPI `bits`
setting are transferred. Fixes#7511.
MicroPython implements some 3.5+ features, and this change helps to reduce
the need for some .exp files in the test suite.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Adds support for hardware SPI to the zephyr port. Consistent with other
ports, such as rp2 and stm32, we only implement the SPI protocol functions
(init and transfer). Explicit sck/mosi/miso selection is not supported
and new SPI instances are initialized with default values.
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
These warnings appear with GCC 11. Keep them as warnings but not as
compiler errors so they can be dealt with properly in the future.
Signed-off-by: Damien George <damien@micropython.org>
The ADC_FIRST_GPIO_CHANNEL and ADC_LAST_GPIO_CHANNEL macros are no longer
needed. Instead the pin_adcX table (X = 1, 2, 3) is now generated to be
the exact size needed for a given MCU, and MP_ARRAY_SIZE(pin_adcX) is used
to determine the upper bound.
This commit also allows CPU pins to be excluded from ADC configuration if
they are hidden by prefixing their name with a "-".
Signed-off-by: Damien George <damien@micropython.org>
* Modify common functions in adc.c to accept ADC handle.
* Most external channels are connected to ADC12 which is used by default.
* For ADCAll (internal channels) ADC3 is used instead.
* Issue #4435 is possibly related (at least partially fixed).
This change allows specification of the idle level and TX carrier output
level (through changed initialisation API), and more flexible specification
of pulses for write_pulses.
This is a breaking change for the esp32.RMT constructor API. Previous code
of this form:
esp32.RMT(..., carrier_duty_percent=D, carrier_freq=F)
will now raise an exception and should be changed to:
esp32.RMT(..., tx_carrier=(F, D, 1))
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.
The Makefile had to be changed in order to build the .bin file as well.
This adds a call to mp_deinit() in the main function of the STM32 port.
This enables the use of MICROPY_PORT_DEINIT_FUNC on that port, as well as
cleaning up the GIL if threading is enabled.
Previous behaviour was: if boot.py had an exception then main.py would
still run, which is arguably unexpected behaviour.
This commit changes the behaviour so main.py is not run if boot.py has an
error.
Signed-off-by: Damien George <damien@micropython.org>
This avoids the irritation of the PJRC HalfKay loader on Teensy 4.0. Block
0 and 1 are properly erased and the additional formatting in the make
script is not required anymore.
This class supports SPI bus controller mode, with blocking transfers.
SPI device numbers start at 0, to comply with the pinout of the Teensy
boards. With the configured clock frequency the fastest baud rate is
33MHz. For messages longer 16 bytes DMA is used. The class uses the
existing framework with extmod/machine_spi.c.
Extended driver options:
- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
Since the pins used by the SPI are fixed, no Pin settings can be made.
Thus the drive option is added allowing to control ringing and crosstalk
on the connection.
- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
Default is 2 clock cycles.
When looping, now disable the TX interrupt after calling rmt_write_items()
function to handle change in IDF behaviour (since v4.1). Also check length
of pulses to ensure it fits hardware limit.
Fixes issue #7403.
The GC now works correctly using asyncify and the functions
emscripten_scan_stack() and emscripten_scan_registers(). Stack/call depth
is monitored via the use of the pystack option.
Fixes issue #6738.
Signed-off-by: Damien George <damien@micropython.org>
Calculating the weekday each time you want to set a date is error prone and
tiresome. MicroPython can do it on its own - hardware on some ports do not
support storing weekday in hardware and always computes it on the fly,
ignoring the value given to the constructor.
During discussion for #7432 the conclusion was that there seems to be no
obvious reason to let user set the weekday to an incorrect value so it
makes sense to just ignore the provided weekday value and always compute
the correct value. This patch introduces this change for the rp2 port.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
The RTC in rp2 can store any, even wrong, number as a weekday in RTC. It
was, however, discussed in #7394 that we would like to unify all ports and
use 0 as Monday, not Sunday in the machine.RTC implementation.
This patch makes sure that the default date set in RTC is adheres to this
convention. It also fixes the example in quickref to use proper weekday to
avoid confusion.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Add an optional 'lock' kwarg to callback that locks GC and scheduler. This
allows the callback to be invoked asynchronously in 'interrupt context',
for example as a signal handler.
Also add the 'cfun' member function to callback, that allows retrieving the
C callback function address. This is needed when the callback should be
set to a struct field.
See related #7373.
Signed-off-by: Amir Gonnen <amirgonnen@gmail.com>
It reschedules the BT HCI poll soft timer so that it is called exactly when
the next timer expires.
Signed-off-by: Damien George <damien@micropython.org>
Instead of using systick the BT subsystem is now scheduled using a soft
timer. This means it is scheduled only when it is enabled.
Signed-off-by: Damien George <damien@micropython.org>
And call mp_pairheap_init_node() in soft_timer_static_init() so that
reinsert can be called after static_init.
Signed-off-by: Damien George <damien@micropython.org>
Dynamically generate/loaded native code (eg from @micropython.native or
native .mpy files) needs to be able allocate from IRAM, and the memory
protection feature must be disabled for that to work. Disabling it is
needed to get native code working on ESP32-S2 and -C3.
Signed-off-by: Damien George <damien@micropython.org>
This introduces a new macro to get the main thread and uses it to ensure
that asynchronous exceptions such as KeyboardInterrupt (CTRL+C) are only
scheduled on the main thread. This is more deterministic than being
scheduled on a random thread and is more in line with CPython that only
allow signal handlers to run on the main thread.
Fixes issue #7026.
Signed-off-by: David Lechner <david@pybricks.com>
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
Commit 0abf6f830c removed _boot.py from the
manifest for the GENERIC_512K board because the build does not include a
filesystem. But the main code expects _boot.py to be there and prints an
error if it's not. So add a custom _boot.py, which just sets the
gc.threshold().
Signed-off-by: Damien George <damien@micropython.org>
