This is needed so that the floppy flux reader can enable the pull up
on the index pin while using it as a pio jmp pin.
Also fixes a doc bug where the `jmp_pin` was omitted in one spot in the docs.
Per Scott, the purpose of this trick is to make the board programmable from Arduino even when CP is installed, so my convenience of escaping into UF2 is not going to work out.
This makes it easier to blanket never reset flash and USB pins. It
also allows us to set a custom state after reset. The first case
is for the double tap reset that needs to be pulled low.
Fixes#5893
This tweaks the RMT timing to better match the 1/3 and 2/3 of 800khz
guideline for timing. It also ensures a delay of 300 microseconds
with the line low before reset.
Pin reset is now changed to the IDF default which pulls the pin up
rather than CircuitPython's old behavior of floating the pin.
Fixes#5679
The bit-bang implementation was replaced with the RMT implementation in
599b61c086. This commit brings back that
bit-bang code, and allows it to be selected via the new static method:
esp32.RMT.bitstream_channel(None)
The bit-bang implementation may be useful if the RMT needs to be used for
something else, or if bit-banging is more stable in certain applications.
Signed-off-by: Damien George <damien@micropython.org>
MicroPython currently runs on core 0 of the esp32. Calling
rmt_driver_install will mean that the RMT interrupt handler is also
serviced on core 0. This can lead to glitches in the RMT output if
WiFi is enabled (for esp32.RMT and machine.bitstream).
This patch calls rmt_driver_install on core 1, ensuring that the RMT
interrupt handler is serviced on core 1. This prevents glitches.
Fixes issue #8161.
Signed-off-by: Damien George <damien@micropython.org>
Initially enabled for samd51, this enables reading raw flux data as well
as DOS/MFM formatted media.
This is only the low-level code for reading & decoding flux pulses from a floppy drive.
high level details will live in a Python library.
adafruit-circuitpython-floppy will take care of details like stepping
from track to track, etc.
The port is free to return NULL for any/all of these, and the caller has
to check.
This will be used in the floppy code, because aside from getting the
registers, it looks like all is independent of MCU.
This brings the pins in line with the documented [pinouts]. The only
"special" pins:
- GP0, GP1 are mentioned as the default UART, so we init them as
such and give them the TX and RX alternative names.
- GP16 is connected to the onboard neopixel DIN line and we assign it
the NEOPIXEL name. (Power of the neopixel is connected to the 3.3V
rail, not a pin. See [schematic].)
- GP26, GP27, GP28, GP29 have unambiguous ADC designations in the
[pinouts], so we assign the `A` analogue names as the Pico board
definition does.
[pinouts]: https://www.waveshare.com/wiki/RP2040-Zero#Pinouts
[schematic]: https://www.waveshare.com/w/upload/4/4c/RP2040_Zero.pdf
If, for some reason, you mix up TX and RX when calling `busio.UART` (who would do that ;) ), you get `Invalid pins`. When you go to try again, you'll get `All UART peripherals are in use` because the interface was claimed as busy before pins are verified. This should fix that issue.
The main Makefile builds the mpy-cross executable automatically if
it doesn't exist since 78718fffb1,
so build it first to make sure it doesn't get needlessly rebuilt.
This board has only 2MiB of flash so the build needs to be reduced in size
to fit. Commit 549448e8bb made all boards
build with -O2 by default (for performance) so this overrides that default.
Signed-off-by: Damien George <damien@micropython.org>
This is needed because these ports allocate mbedtls data on the MicroPython
heap, and SSL socket objects must be fully cleaned up when they are garbage
collected, to free this memory allocated by mbedtls. As part of this,
gc_sweep_all() will now ensure that the MP_STATE_PORT(mbedtls_memory)
linked-list is fully deallocated on soft reset.
Signed-off-by: Damien George <damien@micropython.org>
CONFIG_USB was removed in Zephyr v2.7.0 after some Kconfig rework that
made it sufficient to use CONFIG_USB_DEVICE_STACK only.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Updates the Zephyr port to get the UART console device from devicetree
instead of Kconfig. The Kconfig option CONFIG_UART_CONSOLE_ON_DEV_NAME
was removed in Zephyr v2.7.0.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
The reboot header was moved to a different path in Zephyr v2.6.0. The
old path was deprecated for two releases (v2.6.0 and v2.7.0) and will no
longer be supported after Zephyr v2.7.0.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
As a prerequisite to upgrading to Zephyr v2.7.0, upgrade the minimum
CMake version required for the Zephyr port to 3.20.0.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
After changing the bitstream implementation to use the RMT driver in
commit 72d86158121e32bbabaeade08f449d507bf40f9a
("esp32/machine_bitstream.c: Replace with RMT-based driver."), using
multiple `Neopixel` instances shows signal duplication between the
instances (i.e. a `write()` on one instance is written to all instances).
On invocation, the rmt driver configures the GPIO matrix to route the
output signal to the respective GPIO pin. When called for a different
`NeoPixel` instance using a different pin, the new route is established,
but the old route still exists. Now, the RMT output signal is sent to both
pins.
Fix this by setting the standard GPIO output function for the current pin
after uninstalling the RMT driver.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
In commit 86ce442607 the '.frozen' entry was
added at the start of sys.path, to allow control over when frozen modules
are searched during import, and retain existing behaviour whereby frozen
was searched before the filesystem.
But Python semantics of sys.path require sys.path[0] to be the directory of
the currently executing script, or ''.
This commit moves the '.frozen' entry to second place in sys.path, so
sys.path[0] retains its correct value (described above).
Signed-off-by: Damien George <damien@micropython.org>
Save and restore the same duty cycle when the frequency (or frequency
resolution) is changed. This allows a smooth frequency change.
Also update the esp32 PWM quickref to be clearer.
These removed ones are either unused by MicroPython or provided by osapi.h
in the SDK. In particular ets_delay_us() has different signatures for
different versions of the SDK, so best to let it provide the declaration.
Fixes issue #8095.
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values. This keeps all bare-metal ports aligned.
Signed-off-by: Damien George <damien@micropython.org>
Frozen modules will be searched preferentially, but gives the user the
ability to override this behavior.
This matches the previous behavior where "" was implicitly the frozen
search path, but the frozen list was checked before the filesystem.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This feature is not enabled on any port, it's not in CPython's io module,
and functionality is better suited to the micropython-lib implementation of
pkg_resources.
Default SPI pins are now correctly assigned by machine_hw_spi.c even for S2
and S3. mpconfigboard.h files define defaults with flipped SPI(1) and
SPI(2) to workaround a bug in machine_hw_spi.c - the bug is fixed.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Use IO_MUX pins as defined by ESP IDF in soc/esp32/include/soc/spi_pins.h
ESP32S2 and S3 don't have IO_MUX pins for SPI3, GPIO matrix is always used.
Choose suitable defaults for S2 and S3.
ESP32C3 does not have SPI3 at all. Don't define pin mappings for it.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Use IO_MUX pins as defined by ESP IDF in soc/esp32*/include/soc/spi_pins.h
Alternatively use now deprecated HSPI_IOMUX_PIN_NUM_xxx
(or FSPI_IOMUX_PIN_NUM_xxx for ESP32S2) for compatibility with IDF 4.2
and older.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
The index of machine_hw_spi_obj and machine_hw_spi_default_pins arrays is
assigned to 0 for ARG_id==HSPI_HOST and 1 for another SPI. On ESP32S2 and
S3 HSPI_HOST=2 so the first set (idx=0) of default pins is used for
SPI(id=2) aka HSPI/SPI3 and the second set (idx=1) for SPI(id=1) aka
FSPI/SPI2. This makes a misleading mess in MICROPY_HW_SPIxxxx definitions
and it is also in contradiction to the comments around the definitions.
Change the test of ARG_id to fix the order of machine_hw_spi_default_pins.
This change might require adjusting MICROPY_HW_SPIxxxx definitions in
mpconfigboard.h of S2/S3 based boards.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
- Move the qspi_xxxx_flash_config.c files to hal.
It turned out that they are less board than flash type specific.
- Change to a common flexspi_flash_config.h header file.
Thanks for the hint, Damien. The DEBUG build got very large recently.
The major difference is, that inline function are now inlined and
not included as a function. That's good and maybe bad. The good thing is,
that the code speed si now close to the final code. It could be worse
in single step debugging. I'll see.
Setting this option caused a new warning and a formatting error
to pop up at different places. Fixed as well.
The ID is read in a single function and used for:
- machine.unique_id()
- Ethernet MAC addresses.
- ...
That facilitates use of other MCU using a different access method for
the ID (e.g. i.MX RT1176).
Just another choice for the PHY interface.
Added: Keyword option phy_clock=LAN.IN or LAN.OUT
to define the source of the 50MHZ clock for the PHY
interface. The RMII clock is not enabled if it
is generated by a PYH board. Constants:
LAN.IN The clock is provided by the PHY board.
LAN.OUT The clock is provided by the MCU board.
The default is LAN.OUT or the value set in mpconfigboard.h, which
is currently set to IN only for the SEEED ARCH MIX board. Usage etc:
lan = LAN(phy_type=LAN.PHY_DP83848, phy_clock=LAN.IN)
The initial problem with a wrong ICMP checksum was caused by
the test code setting a checksum and the HW taking that probably as
the start value and ending up with 0xffff. With a checksum field of 0
set by the test code the HW creates the proper checksum.
Useful for boards without a PHY interface, where that has to be
attached. Like the Seed ARCH MIX board or Vision SOM. Phy drivers
supported so far are:
- KSZ8081
- DP83825
- LAN8720
More to come. Usage e.g.:
lan = LAN(phy_type=LAN.PHY_LAN8720, phy_addr=1)
The default values are those set in mpconfigboard.h.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
The pico-sdk 1.3.0 update in 97a7cc243b
introduced a change that broke RP2 Bluetooth UART, and possibly UART in
general, which stops working right after UART is initialized. The commit
raspberrypi/pico-sdk@2622e9b enables the UART receive timeout (RTIM) IRQ,
which is asserted when the receive FIFO is not empty, and no more
characters are received for a period of time.
This commit makes sure the RTIM IRQ is handled and cleared in
uart_service_interrupt.
The current ST HAL does not support reading the extended CSD so cannot
correctly detect the capacity of high-capacity cards. As a workaround, the
capacity can be forced via the MICROPY_HW_MMCARD_LOG_BLOCK_NBR config
option.
Signed-off-by: Damien George <damien@micropython.org>
These were commented correctly by their colour, but in the wrong order with
respect to the PCB silkscreen.
Fixes issue #8054.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For the coverage build this reduces the binary size to about 1/4 of its
size, and seems to help gcov/lcov coverage analysis so that it doesn't miss
lines.
Signed-off-by: Damien George <damien@micropython.org>
This adds PL011 UART support which is more plentiful.
It also:
* Fixes PI4 build by including .dtb files on the SD card.
* Enables the activity LED as the status LED on PI4 and CM4 I/O.
* Adds that LED as board.LED.
Fixes#5650 and progress on #5629
All 3 micros we care about (S2, S3, C3) state in the documentation
that DMA channel can be specified as SPI_DMA_CH_AUTO.
Specifying a specific DMA channel explicitly doesn't _ever_ work on
ESP32-S3, so no SPI bus could be used.
Testing performed: On the ESP32-S3-DevKitC, used neopixel_spi to
turn the onboard neopixel red, green, and blue
The methods duty_u16() and duty_ns() are implemented to match the existing
docs. The duty will remain the same when the frequency is changed.
Standard ESP32 as well as S2, S3 and C3 are supported.
Thanks to @kdschlosser for the fix for rounding in resolution calculation.
Documentation is updated and examples expanded for esp32, including the
quickref and tutorial. Additional notes are added to the machine.PWM docs
regarding limitations of hardware PWM.
Instead of board pins, so that pins which have only the CPU specified in
pins.csv can still be used with mp_hal_pin_config_alt_static().
Signed-off-by: Damien George <damien@micropython.org>
A board can now define the following linker symbols to configure its flash
storage layout:
_micropy_hw_internal_flash_storage_start
_micropy_hw_internal_flash_storage_end
_micropy_hw_internal_flash_storage_ram_cache_start
_micropy_hw_internal_flash_storage_ram_cache_end
And optionally have a second flash segment by configuring
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE_SEGMENT2 to 1 and defining:
_micropy_hw_internal_flash_storage2_start
_micropy_hw_internal_flash_storage2_end
Signed-off-by: Damien George <damien@micropython.org>
This reduces code size and code duplication, and fixes `pyb.usb_mode()` so
that it now returns the correct string when in multi-VCP mode (before, it
would return None when in one of these modes).
Signed-off-by: Damien George <damien@micropython.org>
- update esp-idf to v4.4
- add esp32s3 support
- add analogio on esp32c3
- disable rgbmatrix on all espressif soc
Co-authored-by: Scott Shawcroft <scott@adafruit.com>
Co-authored-by: Seon Rozenblum <seon@unexpectedmaker.com>
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle. The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.
Extensions: support PWM for channel pairs. Channel pairs are declared by
supplying 2-element tuples for the pins. The two channels of a pair must
be the A/B channel of a FLEXPWM module. These form than a complementary
pair.
Additional supported keyword arguments:
- center=value Defines the center position of a pulse within the pulse
cycle. The align keyword is actually shortcut for center.
- sync=True|False: If set to True, the channels will be synchronized to a
submodule 0 channel, which has already to be enabled.
- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
channels are Center-Aligned or Edge-aligned. The channels must be either
complementary a channel pair or a group of synchronized channels. It may
as well be applied to a single channel, but withiout any benefit.
- invert= 0..3. Controls ouput inversion of the pins. Bit 0 controls the
first pin, bit 1 the second.
- deadtime=time_ns time of complementary channels for delaying the rising
slope.
- xor=0|1|2 xor causes the output of channel A and B to be xored. If
applied to a X channel, it shows the value oif A ^ B. If applied to an A
or B channel, both channel show the xored signal for xor=1. For xor=2,
the xored signal is split between channels A and B. See also the
Reference Manual, chapter about double pulses. The behavior of xor=2 can
also be achieved using the center method for locating a pulse within a
clock period.
The output is enabled for board pins only.
CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output. That applies only to FLEXPWM pins. The
use of QTMR pins which are not board pins will be rejected.
As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
This is to make the builds for all nucleo/discovery boards uniform, so they
can be treated the same by the auto build scripts.
The CI script is updated to explicitly enable mboot and packing, to test
these features.
Signed-off-by: Damien George <damien@micropython.org>
This prevents SPI4/5 from being used if SDIO and CYW43 are enabled, because
the DMA for the SDIO is used on an IRQ and must be exclusivly available for
use by the SDIO peripheral.
Signed-off-by: Damien George <damien@micropython.org>
Because DMA2 may be in use by other peripherals, eg SPI1.
On PYBD-SF6 it's possible to trigger a bug in the existing code by turning
on WLAN and connecting to an AP, pinging the IP address from a PC and
running the following code on the PYBD:
def spi_test(s):
while 1:
s.write('test')
s.read(4)
spi_test(machine.SPI(1,100000000))
This will eventually fail with `OSError: [Errno 110] ETIMEDOUT` because
DMA2 was turned off by the CYW43 driver during the SPI1 transfer.
This commit fixes the bug by removing the code that explicitly disables
DMA2. Instead DMA2 will be automatically disabled after an inactivity
timeout, see commit a96afae90f
Signed-off-by: Damien George <damien@micropython.org>
Quail (https://www.mikroe.com/quail, PID: MIKROE-1793) is based on an
STM32F427VI CPU, featuring 2048 kB of Flash memory and 192 kB of RAM. An
on-board Cypress S25FL164K adds 8 MB of SPI Flash.
Quail has 4 mikroBUS(TM) sockets for Mikroe click(TM) board connectivity,
along with 24 screw terminals for connecting additional electronics and two
USB ports (one for programming, the other for external mass storage).
4 UARTs, 2 SPIs and 1 I2C bus are available for communication.
Signed-off-by: Lorenzo Cappelletti <lorenzo.cappelletti@gmail.com>
Was incorrectly added as 7MB for an 8MB SPI flash, but this board has a
16MB chip, not 8MB, so it should be 15MB leaving 1MB for MicroPython.
Thanks to @robert-hh
The rp2.StateMachine.exec errors when supplying a sideset action. This
commit passes the sideset_opt from the StateMachine though to the parser.
It also adds some value validation to the sideset operator.
Additionally, the "word" method is added to the exec to allow any other
unsupported opcodes.
Fixes issue #7924.
