Originally, black_bindings found each contiguous "//|" block and sent
it to black independently. This was slower than it needed to be.
Instead, swap the comment prefix: when running black, take off
"//|" prefixes and put "##|" prefixes on all un-prefixed lines.
Then, after black is run, do the opposite operation
This more than doubles the overall speed of "pre-commit run --all",
from 3m20s to 55s CPU time on my local machine (32.5s to under 10s
"elapsed" time)
It also causes a small amount of churn in the bindings, because
black now sees enough context to know whether one 'def' follows another
or ends the 'def's in a 'class'. In the latter case, it adds an extra
newline, which becomes a "//|" line.
I'm less sure why a trailing comma was omitted before down in
rp2pio/StateMachine.c but let's roll with it.
My pings go out, and then they come back
```py
import os
import wifi
import ipaddress
wifi.radio.connect(os.getenv('WIFI_SSID'), os.getenv('WIFI_PASSWORD'))
ipv4 = ipaddress.ip_address("8.8.4.4")
print("Ping google.com: %f ms" % (wifi.radio.ping(ipv4)*1000))
```
Formerly, py/formatfloat would print whole numbers inaccurately with
nonzero digits beyond the decimal place. This resulted from its strategy
of successive scaling of the argument by 0.1 which cannot be exactly
represented in floating point. The change in this commit avoids scaling
until the value is smaller than 1, so all whole numbers print with zero
fractional part.
Fixes issue #4212.
Signed-off-by: Dan Ellis dan.ellis@gmail.com
* Tweak scroll area position so last line is complete and top is
under the title bar.
* Pick Blinka size based on the font to minimize unused space in
title bar. Related to #2791
* Update the title bar after terminal is started. Fixes#6078Fixes#6668
If a changed file is in frozen, supervisor, shared-bindings,
shared-module or common-hal, then compute board settings to
determine if it is impacted.
This should reduce the boards built for changes that are in those
directories.
- define CIRCUITPY_BUILD_EXTENSIONS to predefined values
- set CIRCUITPY_BUILD_EXTENSIONS in port and board config
- reuse the support matrix "get_settings_from_makefile" to get it
- move the existing port and board specific values
- remove the C3 specific board values because it's not the default
- update build_release_files.py to use get_settings_from_makefile
A recent build failed. The original error seemed to be during ci_fetch_deps
where a build message said
```
fatal: reference is not a tree: 346c936e14c6ea3a8d3d65cb1fa46202dc92999d
fatal: Unable to checkout '346c936e14c6ea3a8d3d65cb1fa46202dc92999d' in submodule path 'extmod/ulab'
```
(along with other problems), but this step didn't signal failure to
github actions.
By adding the check= parameter, a failure of the subprocess will cause
a CalledProcessError to be raised, which will make ci_fetch_deps exit with
nonzero status. In turn, this should let Actions understand that something
went wrong with this step, instead of waiting for some subsequent step(s)
to go wrong.
This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
