This gets basic machine.lightsleep([n]) behaviour working on the rp2 port.
It supports:
- Calling lightsleep without a specified period, in which case it uses xosc
dormant mode. There's currently no way to wake it up from this state,
unless you write to raw registers to enable a GPIO wake up source.
- Calling lightsleep with a period n in milliseconds. This period must be
less than about 72 minutes and uses timer alarm3 to wake it up.
The RTC continues to run during lightsleep, but other peripherals have
their clock turned off during the sleep.
It doesn't yet support longer periods than 72 minutes, or waking up from
GPIO IRQ.
Measured current consumption from the USB port on a PICO board is about
1.5mA when doing machine.lightsleep(5000), and about 0.9mA when doing
machine.lightsleep().
Addresses issue #8770.
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- Guard entire file with MICROPY_PY_LWIP, so it can be included in the
build while still being disabled (for consistency with other extmod
modules).
- Add modlwip.c to list of all extmod source in py/py.mk and
extmod/extmod.cmake so all ports can easily use it.
- Move generic modlwip GIT_SUBMODULES build configuration code from
ports/rp2/CMakeLists.txt to extmod/extmod.cmake, so it can be reused by
other ports.
- Remove now unnecessary inclusion of modlwip.c in EXTMOD_SRC_C in esp8266
port, and in SRC_QSTR in mimxrt port.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise include directories are added unconditionally to the build
variables if the component (submodule) is checked out. This can lead to,
eg, the esp32 build using lib/lwip header files, instead of lwip header
files from the IDF.
Fixes issue #8727.
Signed-off-by: Damien George <damien@micropython.org>
Also remove redundant modusocket.c and modnetwork.c sources, they are
already added by extmod/extmod.cmake.
Signed-off-by: Damien George <damien@micropython.org>
The callback passed to add_alarm_in_ms must return microseconds, even
though the initial delay is in milliseconds. Fix this use, and to avoid
further confusion use the add_alarm_in_us function instead.
Signed-off-by: Damien George <damien@micropython.org>
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
This follows on from a5324a1074 and allows
mpy-cross to dynamically select whether ARMv7-M instructions are supported
in @micropython.asm_thumb functions.
The config option MICROPY_EMIT_INLINE_THUMB_ARMV7M is no longer needed, it
is now controlled by MICROPY_EMIT_THUMB_ARMV7M.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
These files that are reformatted only now fall under the list of files to
apply uncrustify/black formatting to.
Signed-off-by: Damien George <damien@micropython.org>
Duplication of characters is caused by re-entrant calls from separate cores
of uart_fill_tx_fifo(). This patch uses a mutex to ensure that a
re-entrant execution of the function returns without affecting the UART
FIFO.
Fixes issues #8344 and #8360.
Prior to this commit, the USB CDC OUT endpoint got NACK'd if a character
was received but not consumed by the application, e.g. via
sys.stdin.read(). This meant that USB CDC was blocked and no additional
characters could be sent from the host. In particular a ctrl-C could not
interrupt the application if another character was pending.
To fix the issue, the approach in this commit uses a callback tud_cdc_rx_cb
which is called by the TinyUSB stack on reception of new CDC data. By
consuming the data immediately, the endpoint does not stall anymore. The
previous handler tud_cdc_rx_wanted_cb was made obsolete and removed.
In addition some cleanup was done along the way: by adding interrupt_char.c
and removing the existing code mp_hal_set_interrupt_char(). Also, there is
now only one (stdin) ringbuffer.
Fixes issue #7996.
The stack (and arg) of core1 is itself a root pointer, not just the entries
in it. Without this fix the GC could reclaim the entire stack (and
argument object).
Fixes issues #7124 and #7981.
The UART hardware flow control was not working correctly, the receive FIFO
was always fetched and RTS was never deasserted. This is not a problem
when hardware flow control is not used: normally, if the receive FIFO is
full, the UART receiver won't receive data into the FIFO anymore, but the
current implementation fetches from the FIFO and discards it instead.
The problem is that data is discarded even when RTS is enabled.
This commit fixes the issue by only taking from the FIFO if there is room
in the ring buffer to put the character.
Signed-off-by: YoungJoon Chun <yjchun@mac.com>
The correct day-of-week is stored in the RTC (0=Monday, 6=Sunday) so there
is no need to adjust it for the return value of time.localtime().
Fixes issue #7889.
Signed-off-by: Damien George <damien@micropython.org>
The inclusion of `umachine` in the list of built-in modules is now done
centrally in py/objmodule.c. Enabling MICROPY_PY_MACHINE will include this
module.
As part of this, all ports now have `umachine` as the core module name
(previously some had only `machine` as the name).
Signed-off-by: Damien George <damien@micropython.org>
The RP2040 I2C hardware can do writes of length 1 and 2, just not of length
0. So only use software I2C for writes of length 0, to improve
performance.
Also increase the software I2C timeout for zero-length writes to
accommodate the behaviour of a wider range of I2C devices.
Fixes issue #8167.
Signed-off-by: Damien George <damien@micropython.org>
Without these methods a lot of existing "portable" scripts are broken.
This change improves portability by making rp2 machine.UART more compliant
with the documented machine UART interface.
