there return of a read operation that times out with no data received
is inconsistent:
```
Adafruit CircuitPython 7.3.0-beta.1-31-g73f6b4867-dirty on 2022-04-30; Adafruit Feather RP2040 with rp2040
>>>
>>> import board, busio
>>> print(board.UART().read(5))
None
Adafruit CircuitPython 6.3.0 on 2021-06-01; FeatherS2 with ESP32S2
>>> import board,busio
>>> print(board.UART().read(5))
None
Adafruit CircuitPython 7.3.0-beta.1 on 2022-04-07; Adafruit Feather STM32F405 Express with STM32F405RG
>>> import board, busio
>>> print(board.UART().read(5))
None
Adafruit CircuitPython 7.3.0-beta.1-31-g73f6b4867-dirty on 2022-04-28; Teensy 4.1 with IMXRT1062DVJ6A
>>> import board, busio
>>> print(board.UART().read(5))
b''
```
Since I have a PR on this file anyway, I thought I would put in the change to make it consistent
with the other 3 board types I tried. Can not say about any of the others.
As I mentioned in issue #6310 while investigating that the Teensy port
did not support RS485_dir pin on normal GPIO pins, I found that it
was not implemented either as well on some other ports.
So was curious to implement it for RP2040 using same approach as I did
for the MIMXRT in the Pull Request #6328
That is I setup the specified pin as a normal GPIO pin in output mode
and then when you do a write operation it sets the GPIO pin logically
high, and when the write completes I set it logically low.
Note: knowing when I can set it low can be tricky, as you need to make
sure the full output has completed otherwise the data will be corrupted.
I am using: uart_tx_wait_blocking(self->uart);
Which looks like it is supposed to wait until the busy status is no
longer set, which the Reference manual mentioned, but this is leaving
the line logically set longer than I would like.
however I have tried running it with my hacked up version of the
Python Robotis DynamixelSDK and was able to talk to some AX servos.
I did have to change the library slightly for the RP2040, as the
library was erroring out when you did something like uart.read(5)
and it timed out without receiving anything. The RP2040 returned
None whereas I think the Teensy returned an empty set, which is what
it looks like the PySerial original code expects.
Not sure if anyone is interested in this, but thought i would
put it out as PR and see.
The existing code was setup that allowed you to specify an RTS
pin to be used as an RS485 direction pin, however there are no
RTS pins that are exposed on any of the Teensy 4.x boards.
Instead Arduino code base allowed you to specify any GPIO pin to
work instead. So I added the code in to facilitate this.
In addition the alternative code to wrap your own GPIO pin set high and low
around call(s) to uart.write() will not currently work, unless maybe you
fudge it and add your own delays as the write will return after the last
byte was pushed onto the UART’s hardware FIFO queue and as such if you
then immediately set the IO pin low, it will corrupt your output stream.
The code I added detects that you are setup to use the RS485 pin and
before it returns will wait for the UART’s Transfer complete status flag
to be set.
Now a 'once' and a 'loop' buffer can be specified.
'once' is useful for things like writing a neopixel strip in the background,
if you can guarantee the buffer contents are stable until the write is complete.
'loop' is useful for periodic things, like pwm & servos.
both together are useful for some special cases of pwm/servo, where a
transitional waveform needs to be played for one repetition and then
a new waveform needs to be played after that.
The API is renamed to reflect that it's a more generic 'background'
operation.
