This class supports SPI bus controller mode, with blocking transfers.
SPI device numbers start at 0, to comply with the pinout of the Teensy
boards. With the configured clock frequency the fastest baud rate is
33MHz. For messages longer 16 bytes DMA is used. The class uses the
existing framework with extmod/machine_spi.c.
Extended driver options:
- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
Since the pins used by the SPI are fixed, no Pin settings can be made.
Thus the drive option is added allowing to control ringing and crosstalk
on the connection.
- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
Default is 2 clock cycles.
When looping, now disable the TX interrupt after calling rmt_write_items()
function to handle change in IDF behaviour (since v4.1). Also check length
of pulses to ensure it fits hardware limit.
Fixes issue #7403.
The GC now works correctly using asyncify and the functions
emscripten_scan_stack() and emscripten_scan_registers(). Stack/call depth
is monitored via the use of the pystack option.
Fixes issue #6738.
Signed-off-by: Damien George <damien@micropython.org>
Calculating the weekday each time you want to set a date is error prone and
tiresome. MicroPython can do it on its own - hardware on some ports do not
support storing weekday in hardware and always computes it on the fly,
ignoring the value given to the constructor.
During discussion for #7432 the conclusion was that there seems to be no
obvious reason to let user set the weekday to an incorrect value so it
makes sense to just ignore the provided weekday value and always compute
the correct value. This patch introduces this change for the rp2 port.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
The RTC in rp2 can store any, even wrong, number as a weekday in RTC. It
was, however, discussed in #7394 that we would like to unify all ports and
use 0 as Monday, not Sunday in the machine.RTC implementation.
This patch makes sure that the default date set in RTC is adheres to this
convention. It also fixes the example in quickref to use proper weekday to
avoid confusion.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Add an optional 'lock' kwarg to callback that locks GC and scheduler. This
allows the callback to be invoked asynchronously in 'interrupt context',
for example as a signal handler.
Also add the 'cfun' member function to callback, that allows retrieving the
C callback function address. This is needed when the callback should be
set to a struct field.
See related #7373.
Signed-off-by: Amir Gonnen <amirgonnen@gmail.com>
It reschedules the BT HCI poll soft timer so that it is called exactly when
the next timer expires.
Signed-off-by: Damien George <damien@micropython.org>
Instead of using systick the BT subsystem is now scheduled using a soft
timer. This means it is scheduled only when it is enabled.
Signed-off-by: Damien George <damien@micropython.org>
And call mp_pairheap_init_node() in soft_timer_static_init() so that
reinsert can be called after static_init.
Signed-off-by: Damien George <damien@micropython.org>
Dynamically generate/loaded native code (eg from @micropython.native or
native .mpy files) needs to be able allocate from IRAM, and the memory
protection feature must be disabled for that to work. Disabling it is
needed to get native code working on ESP32-S2 and -C3.
Signed-off-by: Damien George <damien@micropython.org>
This introduces a new macro to get the main thread and uses it to ensure
that asynchronous exceptions such as KeyboardInterrupt (CTRL+C) are only
scheduled on the main thread. This is more deterministic than being
scheduled on a random thread and is more in line with CPython that only
allow signal handlers to run on the main thread.
Fixes issue #7026.
Signed-off-by: David Lechner <david@pybricks.com>
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
Commit 0abf6f830c removed _boot.py from the
manifest for the GENERIC_512K board because the build does not include a
filesystem. But the main code expects _boot.py to be there and prints an
error if it's not. So add a custom _boot.py, which just sets the
gc.threshold().
Signed-off-by: Damien George <damien@micropython.org>
This adds a wlan.config(reconnects=N) option to set the number of reconnect
attempts that will be made if the WLAN connection goes down. The default
is N=-1 (infinite retries, current behavior). Setting
wlan.config(reconnects=0) will disable the reconnect attempts.
A nice side effect of reconnects=0 is that wlan.status() will report the
disconnect reason now. See related issue #5326.
Ethernet-PHYs from ESP-IDF (LAN8720, IP101, RTL8201, DP83848) are now
supported in IDF v4.1 and above. PHY_KSZ8041 is only for ESP-IDF 4.3 and
above. ESP32S2 is not supported.
Signed-off-by: Tobias Eydam <eydam-prototyping@outlook.com>
The implementation uses the LPUARTx devices. Up to 8 UARTs can be used,
given that the pins are accessible. E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.
For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1. All other UART are assigned to different Pins:
MIMXRT1010-EVK:
D0/D1 UART 1
D6/D7 UART 2
A0/D4 UART 3
MIMXRT1020-EVK:
D0/D1 UART 1
D6/D9 UART 2
D10/D12 UART 3
D14/D15 UART 4
A0/A1 UART 5
MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
D0/D1 UART 1
D7/D6 UART 2
D8/D9 UART 3
A1/A0 UART 4
This fixes error: cast to smaller integer type 'int' from 'pthread_t'.
pthread_t is defined as long, not as int.
Signed-off-by: Pavol Rusnak <pavol@rusnak.io>
The rtc_set_datetime() from pico-sdk will validate the values in the
datetime_t structure and refuse to set the time if they aren't valid. It
makes sense to raise an exception if this happens instead of failing
silently which might be confusing (as an example, see:
https://github.com/micropython/micropython/pull/6928#issuecomment-860166044
).
The supplied value for microseconds in datetime() will be treated as a
starting value for the reported microseconds. Due to internal processing
in setting the time, there is an offset about 1 ms.
This change moves the datetime tuple format back to the one used by all the
other ports:
(year, month, day, weekday, hour, minute, second, microsecond)
Weekday is a number between 0 and 6, with 0 assigned to Monday. It has to
be provided when setting the RTC with datetime(), but will be ignored on
entry and calculated when needed.
The weekday() method was removed, since that is now again a part of the
datetime tuple.
The now() method was updated so it continues to return a tuple that matches
CPython's datetime module.
Initial support for machine.RTC on rp2 port. It only supports datetime()
method and nothing else. The method gets/returns a tuple of 8 items, just
like esp32 port, for example, but the usec parameter is ignored as the RP2
RTC only works up to seconds precision.
The Pico RTC isn't very useful as the time is lost during reset and there
seems to be no way to easily power up just the RTC clock with a low current
voltage, but still there seems to be use-cases for that, see issues #6831,
and a Thonny issue #1592. It was also requested for inclusion on v1.15
roadmap on #6832.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Changes introduced are:
- the application offset is now loaded from the partition table instead of
being hard-coded to 0x10000
- maximum size of all sections is computed using the partition table
- an error is generated if any section overflows its allocated space
- remaining bytes are printed for each section
Signed-off-by: Damien George <damien@micropython.org>
This commit adds a few math functions to the source list in the Makefile,
and implements the log2f function, so that ulab can be compiled on the nrf
boards. It also addresses part of #5162.
This commit fixes the following problems converting to/from Python integers
and ffi types:
- integers of 8 and 16 bits not working on big endian
- integers of 64 bits not working on 32 bits architectures
- unsigned returns were converted to signed Python integers
Fixes issue #7269.
Currently only advertising and scanning are supported, using the ring
buffer for events (ie not synchronous events at this stage).
The ble_gap_advertise.py multi-test passes (tested on a nucleo_wb55rg
board).
Signed-off-by: Damien George <damien@micropython.org>
Zephyr's default value for CONFIG_NET_SOCKETS_POSIX_NAMES was changed
from false to true between Zephyr v2.5.0 and v2.6.0. This caused
conflicts in MicroPython, which uses the zsock_ prefixed functions, so
disable it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Zephyr's Kconfig symbols and defaults for SDHC/SDMMC disk drivers and
the disk access subsystem were reworked between Zephyr v2.5.0 and
v2.6.0. Update MicroPython accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
