Commit Graph

51 Commits

Author SHA1 Message Date
iabdalkader 9171cb91b1 mimxrt/pendsv: Add MICROPY_BOARD_PENDSV_ENTRIES for board customisation. 2023-03-07 15:57:58 +11:00
Jim Mussared a377302623 extmod/modnetwork: Add network.hostname() and network.country().
This provides a standard interface to setting the global networking config
for all interfaces and interface types.

For ports that already use either a static hostname (mimxrt, rp2) they will
now use the configured value. The default is configured by the port
(or optionally the board).

For interfaces that previously supported .config(hostname), this is still
supported but now implemented using the global network.hostname.

Similarly, pyb.country and rp2.country are now deprecated, but the methods
still exist (and forward to network.hostname).

Because ESP32/ESP8266 do not use extmod/modnetwork.c they are not affected
by this commit.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-03-01 01:26:17 +11:00
robert-hh de1f1dd164 shared/runtime/softtimer: Use consistently the same clock source.
Before, both uwTick and mp_hal_ticks_ms() were used as clock source.  That
assumes, that these two are synchronous and start with the same value,
which may be not the case for all ports.  If the lag between uwTick and
mp_hal_ticks_ms() is larger than the timer interval, the timer would either
rush up until the times are synchronous, or not start until uwTick wraps
over.

As suggested by @dpgeorge, MICROPY_SOFT_TIMER_TICKS_MS is now used in
softtimer.c, which has to be defined in a port's mpconfigport.h with
the variable that holds the SysTick counter.

Note that it's not possible to switch everything in softtimer.c to use
mp_hal_ticks_ms() because the logic in SysTick_Handler that schedules
soft_timer_handler() uses (eg on mimxrt) the uwTick variable directly
(named systick_ms there), and mp_hal_ticks_ms() uses a different source
timer.  Thus it is made fully configurable.
2023-02-16 12:59:48 +11:00
robert-hh 1583c1f670 mimxrt: Set MICROPY_GC_STACK_ENTRY_TYPE to uint32_t for large RAM.
It was uint16_t. The change sets it to uint32_t for devices with SDRAM.

Fixes issue #10366.
2023-01-16 12:26:39 +11:00
robert-hh 28a5107d81 mimxrt/mpconfigport: Remove config options that are set by default.
Remove every setting that is already included in
MICROPY_CONFIG_ROM_LEVEL_FULL_FEATURES.
2022-11-18 15:06:37 +11:00
robert-hh 5e990cc27f mimxrt: Add support for MIMXRT1176 MCUs, and MIMXRT1170_EVK board.
The RT1176 has two cores, but the actual firmware supports only the CM7.
There are currently no good plans on how to use the CM4.

The actual MIMXRT1170_EVK board is on par with the existing MIMXRT boards,
with the following extensions:
- Use 64 MB RAM for the heap.
- Support both LAN interfaces as LAN(0) and LAN(1), with LAN(1)
  being the 1GB interface.

The dual LAN port interface can eventually be adapted as well for the
RT1062 MCU.

This work was done in collaboration with @alphaFred.
2022-11-17 14:11:50 +11:00
Damien George 98cbace299 mimxrt/machine_timer: Use extmod version of machine.Timer.
Signed-off-by: Damien George <damien@micropython.org>
2022-10-27 14:43:03 +11:00
robert-hh 9d2e179fa5 mimxrt: Fix CPU freeze when calling __WFE() in MICROPY_EVENT_POLL_HOOK.
This issue affected i.MX RT 1052, 1062 and 1064.  It seems to be addressed
by Errata ERR006223, which also mentions i.MX RT101x and 102x, but these
devices worked well even without the change.  As a side effect, the current
consumption at an idle REPL drops significantly with this fix.

Fixes issue #7235.
2022-10-27 14:06:12 +11:00
Damien George 8f4c108025 all: Remove MICROPY_PY_IO_FILEIO config option.
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.

This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).

The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled.  So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether.  That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).

Signed-off-by: Damien George <damien@micropython.org>
2022-08-18 11:54:17 +10:00
Jim Mussared 28aaab9590 py/objstr: Add hex/fromhex to bytes/memoryview/bytearray.
These were added in Python 3.5.

Enabled via MICROPY_PY_BUILTINS_BYTES_HEX, and enabled by default for all
ports that currently have ubinascii.

Rework ubinascii to use the implementation of these methods.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-08-12 12:44:30 +10:00
Jim Mussared 092784da19 ports: Remove unused mp_type_{fileio/textio} macros in mpconfigport.h.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-07-26 18:07:22 +10:00
David Lechner 7e4b205cb0 py/mpstate: Drop MICROPY_PORT_ROOT_POINTERS from mp_state_vm_t.
All in-tree uses of MICROPY_PORT_ROOT_POINTERS have been replaced with
MP_REGISTER_ROOT_POINTER(), so now we can remove both
MICROPY_PORT_ROOT_POINTERS and MICROPY_BOARD_ROOT_POINTERS from the code
and remaining config files.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:51:16 +10:00
David Lechner a316a8fdb3 mimxrt: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register all port-specific root
pointers in the mimxrt port.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:34 +10:00
David Lechner a3703584fe extmod/modnetwork: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register mod_network_nic_list and
removes the same from all mpconfigport.h.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:25 +10:00
David Lechner 81dbea1ce3 shared/readline: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register the readline_history root
pointer array used by shared/readline.c and removes the registration from
all mpconfigport.h files.

This also required adding a new MICROPY_READLINE_HISTORY_SIZE config option
since not all ports used the same sized array.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:48:49 +10:00
Damien George 6e71cde6aa ports: Use default VFS config for import_stat and builtin_open.
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.

This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
  nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open

Signed-off-by: Damien George <damien@micropython.org>
2022-05-25 13:04:45 +10:00
Jim Mussared 7d79fd7e8b mimxrt: Make port-specific modules use MP_REGISTER_MODULE.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-05-18 20:56:30 +10:00
Jim Mussared bb794f05b7 extmod: Make port-included extmod modules use MP_REGISTER_MODULES.
_onewire, socket, and network were previously added by the port rather
than objmodule.c.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-05-18 20:49:12 +10:00
Damien George da31ad7aad mimxrt/mbedtls: Use core-provided tracked alloc instead of custom funcs.
Signed-off-by: Damien George <damien@micropython.org>
2022-05-05 10:31:50 +10:00
MikeTeachman 1f6cb8f047 mixmrt/machine_i2s: Add I2S protocol support.
This commit adds support for machine.I2S on the mimxrt port.  The I2S API
is consistent with the existing stm32, esp32, and rp2 implementations.

I2S features:
- controller transmit and controller receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequencies from 8kHz to 48kHz
- 3 modes of operation:
  - blocking
  - non-blocking with callback
  - uasyncio
- configurable internal buffer
- optional MCK

Tested with the following development boards:
- MIMXRT1010_EVK, MIMXRT1015_EVK, MIMXRT1020_EVK, MIMXRT1050_EVK
- Teensy 4.0, Teensy 4.1
- Olimex RT1010
- Seeed ARCH MIX

Tested with the following I2S hardware peripherals:
- UDA1334
- GY-SPH0645LM4H
- WM8960 codec on board the MIMXRT boards and separate breakout board
- INMP441
- PCM5102
- SGTL5000 on the Teensy audio shield

Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
2022-03-30 14:12:40 +11:00
iabdalkader fe8b47e29f ports: Allow boards to define additional network interfaces. 2022-03-24 17:23:28 +11:00
Damien George 9a3e1a1808 mimxrt/moduos: Convert module to use extmod version.
Signed-off-by: Damien George <damien@micropython.org>
2022-03-09 10:03:23 +11:00
robert-hh 4774501cab mimxrt/eth: Avoid a race condition for Ethernet.
That caused Ethernet to lock up at high data rates after ~200MByte data
average in a row.  Tested now with data bursts up to 10 GByte and overall
data rates of ~8MByte/s at the Eth100 port.
2022-03-08 23:11:01 +11:00
Damien George fbd47fc46c ports: Consolidate inclusion of umachine module in built-ins.
The inclusion of `umachine` in the list of built-in modules is now done
centrally in py/objmodule.c.  Enabling MICROPY_PY_MACHINE will include this
module.

As part of this, all ports now have `umachine` as the core module name
(previously some had only `machine` as the name).

Signed-off-by: Damien George <damien@micropython.org>
2022-02-03 10:08:54 +11:00
Damien George 1892d03740 mimxrt,stm32: Enable MICROPY_PY_USSL_FINALISER.
This is needed because these ports allocate mbedtls data on the MicroPython
heap, and SSL socket objects must be fully cleaned up when they are garbage
collected, to free this memory allocated by mbedtls.  As part of this,
gc_sweep_all() will now ensure that the MP_STATE_PORT(mbedtls_memory)
linked-list is fully deallocated on soft reset.

Signed-off-by: Damien George <damien@micropython.org>
2022-01-08 00:02:04 +11:00
robert-hh 81f706aee4 mimxrt: Support PWM using the FLEXPWM and QTMR modules.
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle.  The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.

Extensions: support PWM for channel pairs.  Channel pairs are declared by
supplying 2-element tuples for the pins.  The two channels of a pair must
be the A/B channel of a FLEXPWM module.  These form than a complementary
pair.

Additional supported keyword arguments:

- center=value Defines the center position of a pulse within the pulse
  cycle.  The align keyword is actually shortcut for center.

- sync=True|False: If set to True, the channels will be synchronized to a
  submodule 0 channel, which has already to be enabled.

- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
  channels are Center-Aligned or Edge-aligned.  The channels must be either
  complementary a channel pair or a group of synchronized channels.  It may
  as well be applied to a single channel, but withiout any benefit.

- invert= 0..3. Controls ouput inversion of the pins.  Bit 0 controls the
  first pin, bit 1 the second.

- deadtime=time_ns time of complementary channels for delaying the rising
  slope.

- xor=0|1|2 xor causes the output of channel A and B to be xored.  If
  applied to a X channel, it shows the value oif A ^ B.  If applied to an A
  or B channel, both channel show the xored signal for xor=1.  For xor=2,
  the xored signal is split between channels A and B.  See also the
  Reference Manual, chapter about double pulses.  The behavior of xor=2 can
  also be achieved using the center method for locating a pulse within a
  clock period.

The output is enabled for board pins only.

CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output.  That applies only to FLEXPWM pins.  The
use of QTMR pins which are not board pins will be rejected.

As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
2021-11-24 13:48:27 +11:00
robert-hh 7d7d29dbe2 mimxrt: Fix mp_hal_quiet_timing_enter()/exit() so timer still runs.
The initial code disabled IRQs, which caused the us-ticks timer to stop.
The change here changes the priotity level, such that the timer still runs.
2021-11-16 23:20:06 +11:00
robert-hh 9f6604eb27 mimxrt: Enable the platform module. 2021-10-25 23:54:52 +11:00
robert-hh 4f89c38a6a mimxrt: Optimize the runtime speed.
By moving code to ITCM, like vm, gc, parse, runtime.  The change affects
mostly the execution speed of MicroPython code.  The speed is increased by
up to a factor of 6, especially for MCU with small cache.
2021-10-25 23:54:47 +11:00
robert-hh a12e318948 mimxrt/mpconfigport.h: Enable f-strings. 2021-10-25 23:52:35 +11:00
robert-hh 1866ed7e2e mimxrt/eth: Add LAN support and integrate the network module.
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.

The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0

The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1

Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.

Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works

The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.

Some boards do not wire the RESET and INT pin of the PHY transceiver.  For
operation, these are not required.  If they are defined, they will be used.
2021-10-25 15:14:26 +11:00
robert-hh 61b7c098b9 mimxrt/machine_bitstream: Add bitstream function to machine module.
Following the code example for ESP32 of Jim Mussard.

As a side effect:
- mp_hal_ticks_cpu() was implemented,
- mp_hal_get_cpu_freq() and mp_hal_ticks_cpu_init() were added and used.
- mp_hal_pin_high() and mp_hal_pin_low() were changed for symmetry
2021-09-10 13:32:53 +10:00
Philipp Ebensberger 87f97e490c mimxrt/sdcard: Implement SDCard driver.
- Configures `PLL2->PFD0` with **198MHz** as base clock of
	`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
        to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!

SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.

Signed-off-by: Philipp Ebensberger
2021-09-07 20:45:33 +02:00
Damien George d41f6dde56 extmod/modonewire: Make _onewire module configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George afe0634c98 extmod/machine_spi: Make SoftSPI configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George 122d901ef1 extmod/machine_i2c: Make SoftI2C configurable via macro option.
The zephyr port doesn't support SoftI2C so it's not enabled, and the legacy
I2C constructor check can be removed.

Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
robert-hh 1074c784b0 mimxrt: Add support for Hyperflash chips.
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.

This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
  hyperflash.
- minor incidental changes to other boards so they still build

Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
2021-07-31 16:25:40 +10:00
robert-hh cbc9a591a4 mimxrt/modmachine: Add a few minor methods to the machine module.
Mostly for compatibility reasons:
- idle()
- disable_irq()
- enable_irq()
- time_pulse_us()
2021-06-26 22:27:02 +10:00
robert-hh a262faa227 mimxrt/moduos: Seed the PRNG on boot using the TRNG. 2021-06-26 22:27:02 +10:00
robert-hh 7417c6ac91 mimxrt/machine_pin: Implement pin.irq() functionality. 2021-06-16 01:42:10 +10:00
robert-hh bbdc98f72e mimxrt: Enable many Python and some extmod features.
Besides Python features this includes the extmod modules which make use of
the Pin module, especially machine.softSPI, machine.SoftI2C and onewire.
2021-06-04 00:38:18 +10:00
robert-hh 5226d6e1ee mimxrt: Remove __WFE() from MICROPY_EVENT_POLL_HOOK.
The device is unreliable with the WFE included.  This needs further
investigation.
2021-06-03 12:21:36 +10:00
robert-hh 4c407c790f mimxrt: Add the Timer class to the machine module.
It supports three hardware timer channels based on the PIT timers of the
MIMXRT MCU.  The timer id's are 0, 1 and 2.  On soft reboot all active
timers will be stopped via finalisers.
2021-06-02 00:33:13 +10:00
robert-hh dfd4324eb1 mimxrt: Add flash storage support with VFS and littlefs filesystem.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.

Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS.  VFS
  will take up most of the available flash. 1M is reserved for code.  9K is
  reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c.  All flashing
  related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
  module.

It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.

Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
2021-06-01 23:42:57 +10:00
robert-hh c303b15f10 mimxrt: Enable frozen modules. 2021-06-01 22:57:09 +10:00
robert-hh fdaf2b80d9 mimxrt: Add custom help text and enable help("modules"). 2021-06-01 22:52:44 +10:00
Philipp Ebensberger c326d9a67b mimxrt: Enable built-in help. 2021-05-26 00:12:45 +10:00
Damien George d0e014aa41 mimxrt: Enable CPYTHON_COMPAT, PY_ASYNC_AWAIT, PY_ATTRTUPLE options.
This change allows running the tests in tests/basics/ without any failures
(but some tests are still skipped).

Signed-off-by: Damien George <damien@micropython.org>
2021-04-14 12:55:53 +10:00
Damien George f31c6b4840 mimxrt: Fix USB CDC handling so it works reliably.
On i.MX the SysTick IRQ cannot wake the CPU from a WFI so the CPU was
blocked on WFI waiting for USB data in mp_hal_stdin_rx_chr() even though it
had already arrived (because it may arrive just after calling the check
tud_cdc_available()).  This commit fixes this problem by using SEV/WFE to
indicate that there has been a USB event.

The mp_hal_stdout_tx_strn() function is also fixed so that it doesn't
overflow the USB buffers.

Signed-off-by: Damien George <damien@micropython.org>
2021-02-12 13:48:51 +11:00
Damien George 7c44354592 ports: Remove def of MP_PLAT_PRINT_STRN if it's the same as the default.
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.

Signed-off-by: Damien George <damien@micropython.org>
2021-02-04 22:39:17 +11:00