Prior to this commit, BTstack would only be notified of sent UART data when
the mp_bluetooth_hci_poll() function was called for some other reason, eg
because of incoming data over UART. This is highly suboptimal.
With this commit, BTstack is now notified immediately after UART data has
been sent out. This improves the multi_bluetooth/perf_gatt_char_write.py
performance test by about a factor of 10x for write-without-response, and
about 4x for write-with-response (tested on LEGO_HUB_NO6 as instance1).
Signed-off-by: Damien George <damien@micropython.org>
1. Remove the skip for detecting support for polling user-defined objects
as this is always possible now on all ports.
2. Don't print when the scheduled task runs as the ordering of this
relative to the other prints is dependent on other factors (e.g. if
using the native emitter).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
iobase_ioctl expects that an ioctl method must return an integer, and will
raise otherwise.
This was tripping up aioble on Unix, where the new hybrid modselect.c
implementation will attempt to extract a file descriptor from the pollable
via ioctl(MP_STREAM_GET_FILENO).
However, ThreadSafeFlag's ioctl only supported MP_STREAM_POLL, and returned
None otherwise.
This makes it return `-1` (to match tests/extmod/select_poll_custom.py). It
should probably be `-22` (corresponding to MP_EINVAL), but the value is
never checked, and MP_EINVAL can be a different value on different ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Update expired certificate, increase time validity period to five years and
fix command arguments typos in commentaries.
Signed-off-by: Carlos Gil <carlosgilglez@gmail.com>
Changes are:
- Disable internal flash storage and use the external QSPI for storage.
- Disable default bootloader entry mode. The bootloader entry function
exists in board_init.c.
- Remove OSC enable/disable macros (this board doesn't have an OSC).
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This was previously hard-coded to "Micropy" / "Mass Storage" / "1.0".
Now allow it to be overridden by a board.
Also change "Micropy" to "MicroPy" and "1.0" to "1.00" to match stm32.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was previously hard-coded to "MicroPy" / "pyboard Flash" / "1.00".
Now allow it to be overridden by a board.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Add "CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y" to
ports/esp32/boards/sdkconfig.base so that all micropython esp32 images
support OTA rollback in the bootloader. These images can then be converted
to OTA-capable images as required by user tools.
Also remove CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y from board-specific
sdkconfig files as this is now the default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
While cyw43 is deinitialized, an interrupt occurs. That is handled with
these lines: ports/rp2/mpnetworkport.c#L59-L61 and as pendsv is disabled
while in network code, the poll function then just waits there.
When deinit has finished, the poll func is executed, but skipped:
src/cyw43_ctrl.c#L222-L225 this skips the `CYW43_POST_POLL_HOOK` which
would re-enable interrupts, but also reset `cyw43_has_pending`.
And in that state, the lightsleep code, will skip sleeping as it thinks
there is a network packet pending to be handled.
With this change applied, lightsleep works as expected when the wifi chip
is enabled, and when it's powered off.
The DHCP server broadcasts messages. They are being sent via the default
netif which might be completely the wrong network. We want to send
messages to the netif we got the original message from.
Original author: [Peter Harper](https://github.com/peterharperuk)
Source: https://github.com/raspberrypi/pico-examples/pull/392
Signed-off-by: Samveen <samveen@samveen.in>
Defines the list of standard features and ensures that each board.json
only uses those ones. This list can be extended, but needs to be a
deliberate decision.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Applies to newly-added ARDUINO_PORTENTA_C33 and UM_NANOS3.
Makes the list match the standard features defined in
24a6e951ec.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was copied from minimal/mpconfigport.h, but it doesn't make sense
for general ports.
Add a comment to minimal/mpconfigport.h to explain why it specifically
overrides it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was missed in 692d36d779. Probably
never noticed because everything enables `MICROPY_GC_CONSERVATIVE_CLEAR`,
but found via ASAN thanks to @gwangmu & @chibinz.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This provides a way to build a non-DEBUG host binary that still has symbols
and debug information.
Document this for the unix port, and update a comment in the unix port
Makefile.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The PYBD_SF2 is right on the limit of being able to run this test and so
it succeeds the first two cases and fails the next two with MemoryError.
This causes it to SKIP, but that only works if it's the first thing
printed. So reverse the order of the tests so it fails on the biggest
one first.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This gets the calculation working properly for H5 MCUs, and fixes the
switch statement to switch on csel&7 instead of csel&3.
Signed-off-by: Damien George <damien@micropython.org>
The include of HAL headers should come after the HAL configuration defines,
so that the headers can see whether the defines were made or not, to
provide defaults and configure various things.
Signed-off-by: Damien George <damien@micropython.org>
Integrate DAC support for STM32H5. Implement STM32H5 GPDMA driver. The DMA
driver is largely different from other STM32 variants. To support the DAC
circular mode, memory based linked list DMA descriptors are used.
Signed-off-by: Rene Straub <rene@see5.ch>
Changes are:
- Run ADC on PCLK/16.
- Verify and optimize timings (ADC_STAB_DELAY_US, ADC_SAMPLETIME_DEFAULT).
- Add support for STM32H5 VBAT and COREVDD channels on ADC2.
- Replace ADC constants in machine_adc_locals_dict_table.
- Convert STM32 literal to channel numbers in adc_config_channel with
corresponding STM32 LL library functions (__LL_ADC_IS_CHANNEL_INTERNAL(),
__LL_ADC_CHANNEL_TO_DECIMAL_NB()).
Reasoning for the second last point: the STM32 driver literals are uint32_t
that don't work with MP_ROM_INT() which handles signed 31 bit integers
only. Introduce enumerator machine_adc_internal_ch_t to define external
channels (0..19), internal channels (256..) and the special channel VREF
(0xffff). Values are converted to STM32 literals with adc_ll_channel()
when required in adc_config_and_read_u16().
Signed-off-by: Rene Straub <rene@see5.ch>
Select ADC instance based on pin information to support ADC2 inputs.
Display ADC instance number similar to machine_adc (STM32H5 only):
<ADC2 on Pin(Pin.cpu.F14, mode=Pin.ANALOG) channel=6>
Signed-off-by: Rene Straub <rene@see5.ch>
Fixed the preliminary STM32H5 ADC support for pyb.ADC:
- Run ADC on PCLK/16.
- Use STM32 ADC library channel literals (__HAL_ADC_DECIMAL_NB_TO_CHANNEL).
- Use correct temperature conversion for H5 (30C, 130C calibration points).
Signed-off-by: Rene Straub <rene@see5.ch>
To simulate a partial erase, the code reads a native block, erases it,
and writes back the data before and after the erased area. However, the
current logic was filling the area after the erased block with data
from the beginning of the native block-aligned data, instead of applying
the proper offset.
Fixes#12474.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
If a board needs these outputs then it can define MICROPY_HW_CLK_PLLQ/R.
It saves power to not enable them if they are not needed.
Signed-off-by: Damien George <damien@micropython.org>
Supported from GCC 8 and up, and Compiler Explorer suggests it works as
expected with Clang since 3.6 (2014).
- Fixes situation where building embedded MicroPython with -O0 and
MICROPY_NLR_X64 crashes at runtime (due to nlr_push pushing the
frame pointer register EBP). Closes#12421.
- Allows removing the macOS tweak to undo pushing EBP onto the stack
in the generated function prelude.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Currently, check_esp_err() raises an exception without a location in the
source code, eg:
Traceback (most recent call last):
File "<stdin>", line 8, in <module>
OSError: (-258, 'ESP_ERR_INVALID_ARG')
This commit allows additional error reporting (function, line and file) to
be enabled via detailed exceptions. Change the error reporting config to
#define MICROPY_ERROR_REPORTING (MICROPY_ERROR_REPORTING_DETAILED)
and then exception messages from IDF errors look like:
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: (-258, "0x0102 ESP_ERR_INVALID_ARG in function 'set_duty_u16'
at line 342 in file './machine_pwm.c'")
Signed-off-by: Ihor Nehrutsa <IhorNehrutsa@gmail.com>
Fixes are:
- Reset the module first before changing GPIO1 direction.
- Skip spurious bytes received after reset.
- Use HCI UART ID and baudrate when reinitializing UART.
- Disable all printf output which causes unit-tests to fail.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
