Update the Makefile to handle FROZEN_MANIFEST, and the README with some
small samples on how to use freeze manifests. And add BOARD_DIR to the
Makefile which can be referenced in boards/<board>/mpconfigboard.mk to
include a board specific manifest.
Enable the following features for all boards except
nrf51 boards with SoftDevice present:
- MICROPY_VFS
- MICROPY_PY_NRF
- MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
Add posibility to override linker script "_fs_size" from make by adding the
FS_SIZE parameter. The syntax of value is linker script syntax. For
example, the value of 131072 bytes can be written as 128K like this:
FS_SIZE=128K.
If not set, default value for "_fs_size" from linker script will be used.
Disable MICROPY_FATFS_MULTI_PARTITION configuration because there is no
partition table in the flash for FATFS to read.
Also, set MICROPY_FATFS_MAX_SS to the size of a flash page. For nrf51 the
value 1024 is set. For nrf52/nrf91 the value 4096 is set.
This documents parameters that can be passed to make to enable a specific
file system to included in the build. Also, document the Makefile override
parameter "FS_SIZE" that can be used to tune the size of the flash region
to use as internal flash file system.
Update flash.c to also be compiled in when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled and SoftDevice is
present.
Update bluetooth/ble_drv.c to forward flash events to flash.c when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled.
This commit adds the "nrf" module for port specific modules and objects.
Included in it is the "Flash" object which exposes a block device
implementation to access internal SoC flash.
Thanks to @aykevl aka Ayke van Laethem for the initial implementation.
Calculate the unused flash area on the target device. The values will be
exposed by _unused_flash_start and _unused_flash_length. The start address
and the length are not aligned to either word or pages.
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Call `supervisor.disable_ble_workflow()` and the BLE workflow will
be disabled until the chip is reset.
This also includes a couple fixes:
1. Terminals can now be deinit by setting the tilegrid to NULL. This
prevents using the tilegrid before display is init.
2. Fix BLE serial send amount when sending more than a single packet.
Fixes#5049
On ESP ctrl-c during fake sleep will now stop the sleep. A crash
on real deep sleep is now fixed as well. (Exception string saving
was crashing on reading the deep sleep exception.) Fixes#4010
This also fixes nRF fake sleep after the first time. The internal
variable wasn't being reset early enough. Fixes#4869
Passing in a PWMOut still works but is deprecated. It will be
removed in CircuitPython 8.0.0
This also switches STM32 timer indices and channel indices to
0-based in our pin data rather than `- 1` everywhere. The latter is
more bug prone.
Most of the way for #3264
Tested on Metro M0, Metro M4, Feather S2, Feather nRF52840, Feather
STM32F4 and Arduino RP2040.
nRF CircuitPython boards will now provide the file transfer
service defined here: https://github.com/adafruit/Adafruit_CircuitPython_BLE_File_Transfer
USB capable boards will only advertise if previously bonded to a
device or if the reset button is pressed during the fast blue
flashes on start up. When pressed, the board will restart again but
the blue period will not flash.
Boards without USB will always advertise.
When previously bonded, the advertisement is private so that no
other peers can connect. If advertising publicly, the tx power is
lowered to reduce the likelihood of bonding from a distance.
This PR also fixes issues with loading identities of bonded peers
so that our address can now be resolved and we can resolve others'
addresses when scanning.
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
This commit adds a few math functions to the source list in the Makefile,
and implements the log2f function, so that ulab can be compiled on the nrf
boards. It also addresses part of #5162.
This configuration is used by @ladyada and more often than it should
we've discovered late that a change introduced problems building
there.
By adding this to regular CI, hopefully we learn about and fix these
issues sooner rather than later.
This also removes the need to pin share because we don't use the
status LED while user code is running.
The status flashes fallback to the HW_STATUS LED if no RGB LED is
present. Each status has a unique blink pattern as well.
One caveat is the REPL state. In order to not pin share, we set the
RGB color once. PWM and single color will be shutoff immediately but
DotStars and NeoPixels will hold the color until the user overrides
it.
Fixes#4133
After discussing with danh, I noticed that `a/**/b` would not match `a/b`.
After correcting this and re-running "pre-commit run --all", additional
files were reindented, including the codeformat script itself.
In #4683, tannewt noticed that uncrustify was not running on some
file in common-hal.
I investigated and found that it was not being run on a bunch of paths.
Rather than make incremental changes, I rewrote list_files to work
bsaed on regular expressions; these regular expressions are created from
the same git-style glob patterns.
I spot-checked some specific filenames after this change, and all looks good:
```
$ python3 tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup extmod/virtpin.c ports/raspberrypi/background.h ports/raspberrypi/common-hal/pulseio/PulseIn.c
black --fast --line-length=99 -v tests/thread/thread_exit1.py
```
recursiveloop and int_small are excluded, while PulseIn, virtpin,
and background are included.
Testing running from a subdirectory (not _specifically_ supported though):
```
(cd ports && python3 ../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c)
../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup ../extmod/virtpin.c raspberrypi/common-hal/pulseio/PulseIn.
```
As a side-effect, a bunch more files are re-formatted now. :-P
H7 compatibility problems in port.c and peripherals/exti
NRF build failures due to new use of const for PinAlarm pin objects
Isolated board flash overage on blackpill_with_flash, remove audio modules
Unify USB-related makefile var and C def as CIRCUITPY_USB.
Always define it as 0 or 1, same as all other settings.
USB_AVAILABLE was conditionally defined in supervisor.mk,
but never actually used to #ifdef USB-related code.
Loosely related to #4546
This is handy for remote characteristics because it allows for
the PacketBuffer binding code to have the correct max size. This
PR also adds checks so we don't write outside the outgoing buffer.
Also found a race condition between timer_disable and redraw, which
would happen if I debugger-paused inside common_hal_rgbmatrix_timer_disable
or put a delay or print inside it. That's what pausing inside reconstruct
fixes.
So that the "right timer" can be chosen, `timer_allocate` now gets the `self`
pointer. It's guaranteed at this point that the pin information is accurate,
so you can e.g., find a PWM unit related to the pins themselves.
This required touching each port to add the parameter even though it's
unused everywhere but raspberrypi.
The "word" referred to by BYTES_PER_WORD is actually the size of mp_obj_t
which is not always the same as the size of a pointer on the target
architecture. So rename this config value to better reflect what it
measures, and also prefix it with MP_.
For uses of BYTES_PER_WORD in setting the stack limit this has been
changed to sizeof(void *), because the stack usually grows with
machine-word sized values (eg an nlr_buf_t has many machine words in it).
Signed-off-by: Damien George <damien@micropython.org>
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Add "make submodules" to commands when building for the first time.
Otherwise, on a first time build, the submodules have not been checked out
and a lot of `fatal error: nrfx.h: No such file or directory` errors are
printed.
This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
The nrf52840-mdk-usb-dongle and pca10050 comes with a pre-flashed
bootloader (OpenBootloader).
This commit updates the boards "mpconfigboard.mk" to use DFU as
default flashing method and set the corresponding BOOTLOADER
settings such that nrf52840_open_bootloader_1.2.x.ld linker
script is used.
The default DFU flashing method can be disabled by issuing "DFU=0"
when invoking make. This will lead to "segger" being used as default
flashing tool. When using "DFU=0", the linker scripts will not
compensate for any MBR and Bootloader region being present, and might
overwrite them if they were present.
The commit also removes the custom linker script specific to
nrf52840-mdk-usb-dongle as it now points to a generic.
Updated nrf52840-mdk-usb-dongle's README.md to be more clear on
how to deploy the built firmware.
The port README.md has also been updated. In the list of target
boards a new column has been added to indicate which bootloader
is present on the target board. And for consistency, changed all
examples in the README.md to use "deploy" instead of "flash".
An additional Makefile parameter NRFUTIL_PORT can be set in order
to define the serial port to used for the DFU (Default: /dev/ttyACM0).
The "nrfutil" that is used as flasher towards OpenBootloader is
available for installation through Python "pip".
In case of SD=s140, SoftDevice ID 0xB6 is passed to nrfutil's package
generation which corresponds to SoftDevice s140 v6.1.1.
Add the option for "mpconfigboard.mk" to define whether the
board hosts a bootloader or not. The BOOTLOADER make variable
must be set to the name of the bootloader.
When the BOOTLOADER name is set it is also required to supply
the BOOTLOADER_VERSION_MAJOR and the BOOTLOADER_VERSION_MINOR
from the "mpconfigboards.mk". These will be used to resolve which
bootloader linker script that should be passed to the linker.
The BOOTLOADER section also supplies the C-compiler with
BOOTLOADER_<bootloader name>=<version major><version minor>
as a compiler define. This is for future use in case a bootloader
needs to do modification to the startup files or similar (like
setting the VTOR specific to a version of a bootloader).
Adding variables that can be set from other linker scripts:
- _bootloader_head_size:
Bootloader flash offset in front of the application.
- _bootloader_tail_size:
Bootloader offset from the tail of the flash.
In case the bootloader is located at the end.
- _bootloader_head_ram_size:
Bootloader RAM usage in front of the application.
Updated calculations of application flash and RAM.
This allows calls to `allocate_memory()` while the VM is running, it will then allocate from the GC heap (unless there is a suitable hole among the supervisor allocations), and when the VM exits and the GC heap is freed, the allocation will be moved to the bottom of the former GC heap and transformed into a proper supervisor allocation. Existing movable allocations will also be moved to defragment the supervisor heap and ensure that the next VM run gets as much memory as possible for the GC heap.
By itself this breaks terminalio because it violates the assumption that supervisor_display_move_memory() still has access to an undisturbed heap to copy the tilegrid from. It will work in many cases, but if you're unlucky you will get garbled terminal contents after exiting from the vm run that created the display. This will be fixed in the following commit, which is separate to simplify review.
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
I have a function where it should be impossible to reach the end, so I put in a safe-mode reset at the bottom:
```
int find_unused_slot(void) {
// precondition: you already verified that a slot was available
for (int i=0; i<NUM_SLOTS; i++) {
if( slot_free(i)) {
return i;
}
}
safe_mode_reset(MICROPY_FATAL_ERROR);
}
```
However, the compiler still gave a diagnostic, because safe_mode_reset was not declared NORETURN.
So I started by teaching the compiler that reset_into_safe_mode never returned. This leads at least one level deeper due to reset_cpu needing to be a NORETURN function. Each port is a little different in this area. I also marked reset_to_bootloader as NORETURN.
Additional notes:
* stm32's reset_to_bootloader was not implemented, but now does a bare reset. Most stm32s are not fitted with uf2 bootloaders anyway.
* ditto cxd56
* esp32s2 did not implement reset_cpu at all. I used esp_restart(). (not tested)
* litex did not implement reset_cpu at all. I used reboot_ctrl_write. But notably this is what reset_to_bootloader already did, so one or the other must be incorrect (not tested). reboot_ctrl_write cannot be declared NORETURN, as it returns unless the special value 0xac is written), so a new unreachable forever-loop is added.
* cxd56's reset is via a boardctl() call which can't generically be declared NORETURN, so a new unreacahble "for(;;)" forever-loop is added.
* In several places, NVIC_SystemReset is redeclared with NORETURN applied. This is accepted just fine by gcc. I chose this as preferable to editing the multiple copies of CMSIS headers where it is normally declared.
* the stub safe_mode reset simply aborts. This is used in mpy-cross.
Despite the [silk on the dock board](https://wiki.makerdiary.com/nrf52840-m2-devkit/resources/nrf52840_m2_devkit_hw_diagram_v1_0.pdf), the SDA/SCL pins weren't defined. Though, they were already defined in `mpconfigboard.h`.
Same for RX/TX. It looks like it declared `TXD` and `RXD`, so I didn't want to remove those, but I think it makes sense to have the "standard" pin names, but I moved ithem to illustrate they were all referencing the same pins.
I mimicked the whitespace I saw in the metro_nrf52840_express port.
The mpconfigport.h file is an internal header and should only ever be
included once by mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
