The following code:
server = await asyncio.start_server(...)
async with server:
... code that raises ...
would lose the original exception because the server's task would not have
had a chance to be scheduled yet, and so awaiting the task in wait_closed
would raise the cancellation instead of the original exception.
Additionally, ensures that explicitly cancelling the parent task delivers
the cancellation correctly (previously was masked by the server loop), now
this only happens if the server was closed, not when the task was
cancelled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prior to this commit, BTstack would only be notified of sent UART data when
the mp_bluetooth_hci_poll() function was called for some other reason, eg
because of incoming data over UART. This is highly suboptimal.
With this commit, BTstack is now notified immediately after UART data has
been sent out. This improves the multi_bluetooth/perf_gatt_char_write.py
performance test by about a factor of 10x for write-without-response, and
about 4x for write-with-response (tested on LEGO_HUB_NO6 as instance1).
Signed-off-by: Damien George <damien@micropython.org>
iobase_ioctl expects that an ioctl method must return an integer, and will
raise otherwise.
This was tripping up aioble on Unix, where the new hybrid modselect.c
implementation will attempt to extract a file descriptor from the pollable
via ioctl(MP_STREAM_GET_FILENO).
However, ThreadSafeFlag's ioctl only supported MP_STREAM_POLL, and returned
None otherwise.
This makes it return `-1` (to match tests/extmod/select_poll_custom.py). It
should probably be `-22` (corresponding to MP_EINVAL), but the value is
never checked, and MP_EINVAL can be a different value on different ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a host driver for ESP32 chips running the esp-hosted firmware,
which turns ESP32s into a WLAN/BT co-processor.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
It appears a new session ticket being issued by the server right after
completed handshake is not uncommon and shouldn't be treated as fatal.
mbedtls itself states "This error code is experimental and may be changed
or removed without notice."
Signed-off-by: Mirko Vogt <mirko-dev|mpy@nanl.de>
Whenever the PSA interface is used (if MBEDTLS_PSA_CRYPTO is defined),
psa_crypto_init() needs to be called to initialise the global PSA data
struct, before any PSA related operations.
TLSv1.3 depends on the PSA interface, TLSv1.2 only uses the PSA stack if
MBEDTLS_USE_PSA_CRYPTO is defined.
Without psa_crypto_init() every PSA related call will result in
-0x6C00/-27648 which translates to "SSL - Internal error (eg, unexpected
failure in lower-level module)".
The error is misleading, especially since mbedtls in its docs itself
advices "to return #PSA_ERROR_BAD_STATE or some other applicable error.".
Signed-off-by: Mirko Vogt <mirko-dev|mpy@nanl.de>
Add the buffer attribute to sys.stdin, sys.stdout and sys.stderr. This
provides raw access to underlying stdio streams for the unix port (and
others that use VfsPosix).
Signed-off-by: stephanelsmith <stephane.smith@titansensor.com>
On macOS, if running micropython from subprocess.check_output, then a
stdout.flush() raises error 45.
Here's a test case. This will run fine on linux, but crashes on macOS with
error 45.
import sys
import subprocess
import tempfile
with tempfile.NamedTemporaryFile('w') as fp:
fp.write('''
import sys
sys.stdout.write('hello world')
sys.stdout.flush()
print('')
''')
fp.flush()
print('py3')
o = subprocess.check_output(f'python3 {fp.name}'.split())
print(o)
print('upy')
o = subprocess.check_output(f'micropython {fp.name}'.split())
print(o)
On macOS:
py3
b'hello world\n'
upy
Traceback (most recent call last):
File "...", line 4, in <module>
OSError: 45
On unix:
py3
b'hello world\n'
upy
b'hello world\n'
Signed-off-by: stephanelsmith <stephane.smith@titansensor.com>
The primary purpose of this commit is to make decompress default to
wbits=15 when the format is gzip (or auto format with gzip detected). The
idea is that someone decompressing a gzip stream should be able to use the
default `deflate.DeflateIO(f)` and it will "just work" for any input
stream, even though it uses a lot of memory.
This is done by making uzlib report gzip files as having wbits set to 15
in their header (where it previously only set the wbits out parameter for
zlib files), and then fixing up the logic in `deflateio_init_read`.
Updates the documentation to match.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Otherwise if/when the finaliser runs for this newly created SSLSocket the
mbedtls state will be freed again.
Signed-off-by: Damien George <damien@micropython.org>
This is difficult to implement on cmake-based ports, and having the list
of variants in mpconfigboard.{cmake,mk} duplicates information that's
already in board.json.
This removes the existing query-variants make target from stm32 & rp2
and the definition of BOARD_VARIANTS from the various board files.
Also renames the cmake variable to MICROPY_BOARD_VARIANT to match other
variables such as MICROPY_BOARD. The make variable stays as
BOARD_VARIANT.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
An SSL stream can only handle CLOSE and POLL ioctls. Other ones do not
make sense, or at least it doesn't make sense to pass the ioctl request
directly down to the underlying stream.
In particular MP_STREAM_GET_FILENO should not be passed to the underlying
stream because the SSL stream is not directly related to a file descriptor,
and the SSL stream must handle the polling itself.
Signed-off-by: Damien George <damien@micropython.org>
The signature of this method was poller.poll(timeout=-1, flags=0, /) but
the flags argument was not documented and is not CPython compatible. So
it's removed in this commit.
(The optional flags remains for the ipoll() method, which is documented.)
Signed-off-by: Damien George <damien@micropython.org>
A previous commit removed the unix-specific select module implementation
and made unix use the common one.
This commit adds an optimisation so that the system poll function is used
when polling objects that have a file descriptor. With this optimisation
enabled, if code registers both file-descriptor-based objects, and non-
file-descriptor-based objects with select.poll() then the following occurs:
- the system poll is called for all file-descriptor-based objects with a
timeout of 1ms
- then the bare-metal polling implementation is used for remaining objects,
which calls into their ioctl method (which can be in C or Python)
In the case where all objects have file descriptors, the system poll is
called with the full timeout requested by the caller. That makes it as
efficient as possible in the case everything has a file descriptor.
Benefits of this approach:
- all ports use the same select module implementation
- the unix port now supports polling of all objects and matches bare metal
implementations
- it's still efficient for existing cases where only files and sockets are
polled (on unix)
- the bare metal implementation does not change
- polling of SSL objects will now work on unix by calling in to the ioctl
method on SSL objects (this is required for asyncio ssl support)
Note that extmod/vfs_posix_file.c has poll disable when the optimisation is
enabled, because the code is not reachable when the optimisation is used.
Signed-off-by: Damien George <damien@micropython.org>
This provides similar functionality to the former zlib.DecompIO and
especially CPython's gzip.GzipFile for both compression and decompression.
This class can be used directly, and also can be used from Python to
implement (via io.BytesIO) zlib.decompress and zlib.compress, as well as
gzip.GzipFile.
Enable/disable this on all ports/boards that zlib was previously configured
for.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
There are enough places that implement __exit__ by forwarding directly to
mp_stream_close that this saves code size.
For the cases where __exit__ is a no-op, additionally make their
MP_STREAM_CLOSE ioctl handled as a no-op.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This will be replaced with a new deflate module providing the same
functionality, with an optional frozen Python wrapper providing a
replacement zlib module.
binascii.crc32 is temporarily disabled.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds the SSLContext class to the ssl module, and retains the
existing ssl.wrap_socket() function to maintain backwards compatibility.
CPython deprecated the ssl.wrap_socket() function since CPython 3.7 and
instead one should use ssl.SSLContext().wrap_socket(). This commit makes
that possible.
For the axtls implementation:
- ssl.SSLContext is added, although it doesn't hold much state because
axtls requires calling ssl_ctx_new() for each new socket
- ssl.SSLContext.wrap_socket() is added
- ssl.PROTOCOL_TLS_CLIENT and ssl.PROTOCOL_TLS_SERVER are added
For the mbedtls implementation:
- ssl.SSLContext is added, and holds most of the mbedtls state
- ssl.verify_mode is added (getter and setter)
- ssl.SSLContext.wrap_socket() is added
- ssl.PROTOCOL_TLS_CLIENT and ssl.PROTOCOL_TLS_SERVER are added
The signatures match CPython:
- SSLContext(protocol)
- SSLContext.wrap_socket(sock, *, server_side=False,
do_handshake_on_connect=True, server_hostname=None)
The existing ssl.wrap_socket() functions retain their existing signature.
Signed-off-by: Damien George <damien@micropython.org>
The mod_binascii_a2b_base64() function allocates a buffer which may be
too small. It needs to be no less than three-quarters of the input
length, but is calculated as (<length> / 4) * 3 + 1, which may be less
due to integer division. Changed to (<length> * 3) / 4 + 1.
Signed-off-by: Duncan Lowther <Duncan.Lowther@glasgow.ac.uk>
This allows existing code that does `import uasyncio` or
`import uasyncio as asyncio` to continue working.
It uses the same lazy-loading as asyncio to prevent loading of unused
features.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a MicroPython-specific module that existed to support the old
version of uasyncio. It's undocumented and not enabled on all ports and
takes up code size unnecessarily.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Applies to drivers/examples/extmod/port-modules/tools.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates any includes, and references from Makefiles/CMake.
This essentially reverts what was done long ago in commit
136b5cbd76
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This renames the builtin-modules, such that help('modules') and printing
the module object will show "module" rather than "umodule".
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
To be consistent with MP_UNARY_OP_INT_FLOAT and MP_UNARY_OP_INT_COMPLEX,
and allow int() to first check if a type supports __int__ before trying
other things (as per CPython).
Signed-off-by: Damien George <damien@micropython.org>
Avoiding code duplication. To enable it, set MICROPY_PY_UOS_SYNC in the
port's mpconfigport.h. It is operational only for FAT file system. For
other filesystems it's a no-op.
Signed-off-by: robert-hh <robert@hammelrath.com>
