The search in these cases should include all finally handlers that are
after the current ip. If a handler starts at exactly ip then it is
considered "after" the ip. This can happen when END_FINALLY is followed
immediately by a finally handler (from a different finally).
Consider the function:
def f():
try:
return 0
finally:
print(1)
The current bytecode emitter generates the following code:
00 SETUP_FINALLY 5
02 LOAD_CONST_SMALL_INT 0
03 RETURN_VALUE
04 LOAD_CONST_NONE ****
05 LOAD_GLOBAL print
07 LOAD_CONST_SMALL_INT 1
08 CALL_FUNCTION n=1 nkw=0
10 POP_TOP
11 END_FINALLY
12 LOAD_CONST_NONE
13 RETURN_VALUE
The LOAD_CONST_NONE marked with **** is dead code because it follows a
RETURN_VALUE, and nothing jumps to this LOAD_CONST_NONE. If the emitter
could remove this this dead code it would produce:
00 SETUP_FINALLY 4
02 LOAD_CONST_SMALL_INT 0
03 RETURN_VALUE
04 LOAD_GLOBAL print
06 LOAD_CONST_SMALL_INT 1
07 CALL_FUNCTION n=1 nkw=0
09 POP_TOP
10 END_FINALLY
11 LOAD_CONST_NONE
12 RETURN_VALUE
In this case the finally block (which starts at offset 4) immediately
follows the RETURN_VALUE. When RETURN_VALUE executes ip will point to
offset 4 in the bytecode (because the dispatch of the opcode does *ip++)
and so the finally handler will only be found if a >= comparison is used.
It's a similar story for break/continue:
while True:
try:
break
finally:
print(1)
Although technically in this case the > comparison still works because the
extra byte from the UNWIND_JUMP (encoding the number of exception handlers
to unwind) doesn't have a *ip++ (just a *ip) so ip remains pointing within
the UNWIND_JUMP opcode, and not at the start of the following finally
handler. Nevertheless, the change is made to use >= for consistency with
the RETURN_VALUE change.
Signed-off-by: Damien George <damien@micropython.org>
This is a partial implementation of PEP 448 to allow unpacking multiple
star args in a function or method call.
This is implemented by changing the emitted bytecodes so that both
positional args and star args are stored as positional args. A bitmap is
added to indicate if an argument at a given position is a positional
argument or a star arg.
In the generated code, this new bitmap takes the place of the old star arg.
It is stored as a small int, so this means only the first N arguments can
be star args where N is the number of bits in a small int.
The runtime is modified to interpret this new bytecode format while still
trying to perform as few memory reallocations as possible.
Signed-off-by: David Lechner <david@pybricks.com>
This is a partial implementation of PEP 448 to allow multiple ** unpackings
when calling a function or method.
The compiler is modified to encode the argument as a None: obj key-value
pair (similar to how regular keyword arguments are encoded as str: obj
pairs). The extra object that was pushed on the stack to hold a single **
unpacking object is no longer used and is removed.
The runtime is modified to decode this new format.
Signed-off-by: David Lechner <david@pybricks.com>
This warning can happen on clang 13.0.1 building mpy-cross:
../py/vm.c:748:25: error: array index -3 refers past the last possible
element for an array in 64-bit address space containing 64-bit (8-byte)
elements (max possible 2305843009213693952 elements)
[-Werror,-Warray-bounds]
sp[-MP_OBJ_ITER_BUF_NSLOTS + 1] = MP_OBJ_NULL;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using pointer access instead of array access works around this warning.
Fixes issue #8467.
Signed-off-by: Damien George <damien@micropython.org>
These jumps are always forwards, and it's more efficient in the VM to
decode an unsigned argument. These opcodes are already optimised versions
of the sequence "dup-top pop-jump-if-x pop" so it doesn't hurt generality
to optimise them further.
Signed-off-by: Damien George <damien@micropython.org>
This commit introduces changes:
- All jump opcodes are changed to have variable length arguments, of either
1 or 2 bytes (previously they were fixed at 2 bytes). In most cases only
1 byte is needed to encode the short jump offset, saving bytecode size.
- The bytecode emitter now selects 1 byte jump arguments when the jump
offset is guaranteed to fit in 1 byte. This is achieved by checking if
the code size changed during the last pass and, if it did (if it shrank),
then requesting that the compiler make another pass to get the correct
offsets of the now-smaller code. This can continue multiple times until
the code stabilises. The code can only ever shrink so this iteration is
guaranteed to complete. In most cases no extra passes are needed, the
original 4 passes are enough to get it right by the 4th pass (because the
2nd pass computes roughly the correct labels and the 3rd pass computes
the correct size for the jump argument).
This change to the jump opcode encoding reduces .mpy files and RAM usage
(when bytecode is in RAM) by about 2% on average.
The performance of the VM is not impacted, at least within measurment of
the performance benchmark suite.
Code size is reduced for builds that include a decent amount of frozen
bytecode. ARM Cortex-M builds without any frozen code increase by about
350 bytes.
Signed-off-by: Damien George <damien@micropython.org>
The bytecode state variables mp_showbc_code_start and mp_showbc_constants
have been removed and made local variables passed into the various
functions.
As part of this, the DECODE_PTR macro is fixed so it extracts the relevant
pointer from the child_table (a regression introduced in
f2040bfc7e).
Signed-off-by: Damien George <damien@micropython.org>
Background: .mpy files are precompiled .py files, built using mpy-cross,
that contain compiled bytecode functions (and can also contain machine
code). The benefit of using an .mpy file over a .py file is that they are
faster to import and take less memory when importing. They are also
smaller on disk.
But the real benefit of .mpy files comes when they are frozen into the
firmware. This is done by loading the .mpy file during compilation of the
firmware and turning it into a set of big C data structures (the job of
mpy-tool.py), which are then compiled and downloaded into the ROM of a
device. These C data structures can be executed in-place, ie directly from
ROM. This makes importing even faster because there is very little to do,
and also means such frozen modules take up much less RAM (because their
bytecode stays in ROM).
The downside of frozen code is that it requires recompiling and reflashing
the entire firmware. This can be a big barrier to entry, slows down
development time, and makes it harder to do OTA updates of frozen code
(because the whole firmware must be updated).
This commit attempts to solve this problem by providing a solution that
sits between loading .mpy files into RAM and freezing them into the
firmware. The .mpy file format has been reworked so that it consists of
data and bytecode which is mostly static and ready to run in-place. If
these new .mpy files are located in flash/ROM which is memory addressable,
the .mpy file can be executed (mostly) in-place.
With this approach there is still a small amount of unpacking and linking
of the .mpy file that needs to be done when it's imported, but it's still
much better than loading an .mpy from disk into RAM (although not as good
as freezing .mpy files into the firmware).
The main trick to make static .mpy files is to adjust the bytecode so any
qstrs that it references now go through a lookup table to convert from
local qstr number in the module to global qstr number in the firmware.
That means the bytecode does not need linking/rewriting of qstrs when it's
loaded. Instead only a small qstr table needs to be built (and put in RAM)
at import time. This means the bytecode itself is static/constant and can
be used directly if it's in addressable memory. Also the qstr string data
in the .mpy file, and some constant object data, can be used directly.
Note that the qstr table is global to the module (ie not per function).
In more detail, in the VM what used to be (schematically):
qst = DECODE_QSTR_VALUE;
is now (schematically):
idx = DECODE_QSTR_INDEX;
qst = qstr_table[idx];
That allows the bytecode to be fixed at compile time and not need
relinking/rewriting of the qstr values. Only qstr_table needs to be linked
when the .mpy is loaded.
Incidentally, this helps to reduce the size of bytecode because what used
to be 2-byte qstr values in the bytecode are now (mostly) 1-byte indices.
If the module uses the same qstr more than two times then the bytecode is
smaller than before.
The following changes are measured for this commit compared to the
previous (the baseline):
- average 7%-9% reduction in size of .mpy files
- frozen code size is reduced by about 5%-7%
- importing .py files uses about 5% less RAM in total
- importing .mpy files uses about 4% less RAM in total
- importing .py and .mpy files takes about the same time as before
The qstr indirection in the bytecode has only a small impact on VM
performance. For stm32 on PYBv1.0 the performance change of this commit
is:
diff of scores (higher is better)
N=100 M=100 baseline -> this-commit diff diff% (error%)
bm_chaos.py 371.07 -> 357.39 : -13.68 = -3.687% (+/-0.02%)
bm_fannkuch.py 78.72 -> 77.49 : -1.23 = -1.563% (+/-0.01%)
bm_fft.py 2591.73 -> 2539.28 : -52.45 = -2.024% (+/-0.00%)
bm_float.py 6034.93 -> 5908.30 : -126.63 = -2.098% (+/-0.01%)
bm_hexiom.py 48.96 -> 47.93 : -1.03 = -2.104% (+/-0.00%)
bm_nqueens.py 4510.63 -> 4459.94 : -50.69 = -1.124% (+/-0.00%)
bm_pidigits.py 650.28 -> 644.96 : -5.32 = -0.818% (+/-0.23%)
core_import_mpy_multi.py 564.77 -> 581.49 : +16.72 = +2.960% (+/-0.01%)
core_import_mpy_single.py 68.67 -> 67.16 : -1.51 = -2.199% (+/-0.01%)
core_qstr.py 64.16 -> 64.12 : -0.04 = -0.062% (+/-0.00%)
core_yield_from.py 362.58 -> 354.50 : -8.08 = -2.228% (+/-0.00%)
misc_aes.py 429.69 -> 405.59 : -24.10 = -5.609% (+/-0.01%)
misc_mandel.py 3485.13 -> 3416.51 : -68.62 = -1.969% (+/-0.00%)
misc_pystone.py 2496.53 -> 2405.56 : -90.97 = -3.644% (+/-0.01%)
misc_raytrace.py 381.47 -> 374.01 : -7.46 = -1.956% (+/-0.01%)
viper_call0.py 576.73 -> 572.49 : -4.24 = -0.735% (+/-0.04%)
viper_call1a.py 550.37 -> 546.21 : -4.16 = -0.756% (+/-0.09%)
viper_call1b.py 438.23 -> 435.68 : -2.55 = -0.582% (+/-0.06%)
viper_call1c.py 442.84 -> 440.04 : -2.80 = -0.632% (+/-0.08%)
viper_call2a.py 536.31 -> 532.35 : -3.96 = -0.738% (+/-0.06%)
viper_call2b.py 382.34 -> 377.07 : -5.27 = -1.378% (+/-0.03%)
And for unix on x64:
diff of scores (higher is better)
N=2000 M=2000 baseline -> this-commit diff diff% (error%)
bm_chaos.py 13594.20 -> 13073.84 : -520.36 = -3.828% (+/-5.44%)
bm_fannkuch.py 60.63 -> 59.58 : -1.05 = -1.732% (+/-3.01%)
bm_fft.py 112009.15 -> 111603.32 : -405.83 = -0.362% (+/-4.03%)
bm_float.py 246202.55 -> 247923.81 : +1721.26 = +0.699% (+/-2.79%)
bm_hexiom.py 615.65 -> 617.21 : +1.56 = +0.253% (+/-1.64%)
bm_nqueens.py 215807.95 -> 215600.96 : -206.99 = -0.096% (+/-3.52%)
bm_pidigits.py 8246.74 -> 8422.82 : +176.08 = +2.135% (+/-3.64%)
misc_aes.py 16133.00 -> 16452.74 : +319.74 = +1.982% (+/-1.50%)
misc_mandel.py 128146.69 -> 130796.43 : +2649.74 = +2.068% (+/-3.18%)
misc_pystone.py 83811.49 -> 83124.85 : -686.64 = -0.819% (+/-1.03%)
misc_raytrace.py 21688.02 -> 21385.10 : -302.92 = -1.397% (+/-3.20%)
The code size change is (firmware with a lot of frozen code benefits the
most):
bare-arm: +396 +0.697%
minimal x86: +1595 +0.979% [incl +32(data)]
unix x64: +2408 +0.470% [incl +800(data)]
unix nanbox: +1396 +0.309% [incl -96(data)]
stm32: -1256 -0.318% PYBV10
cc3200: +288 +0.157%
esp8266: -260 -0.037% GENERIC
esp32: -216 -0.014% GENERIC[incl -1072(data)]
nrf: +116 +0.067% pca10040
rp2: -664 -0.135% PICO
samd: +844 +0.607% ADAFRUIT_ITSYBITSY_M4_EXPRESS
As part of this change the .mpy file format version is bumped to version 6.
And mpy-tool.py has been improved to provide a good visualisation of the
contents of .mpy files.
In summary: this commit changes the bytecode to use qstr indirection, and
reworks the .mpy file format to be simpler and allow .mpy files to be
executed in-place. Performance is not impacted too much. Eventually it
will be possible to store such .mpy files in a linear, read-only, memory-
mappable filesystem so they can be executed from flash/ROM. This will
essentially be able to replace frozen code for most applications.
Signed-off-by: Damien George <damien@micropython.org>
This commit removes all parts of code associated with the existing
MICROPY_OPT_CACHE_MAP_LOOKUP_IN_BYTECODE optimisation option, including the
-mcache-lookup-bc option to mpy-cross.
This feature originally provided a significant performance boost for Unix,
but wasn't able to be enabled for MCU targets (due to frozen bytecode), and
added significant extra complexity to generating and distributing .mpy
files.
The equivalent performance gain is now provided by the combination of
MICROPY_OPT_LOAD_ATTR_FAST_PATH and MICROPY_OPT_MAP_LOOKUP_CACHE (which has
been enabled on the unix port in the previous commit).
It's hard to provide precise performance numbers, but tests have been run
on a wide variety of architectures (x86-64, ARM Cortex, Aarch64, RISC-V,
xtensa) and they all generally agree on the qualitative improvements seen
by the combination of MICROPY_OPT_LOAD_ATTR_FAST_PATH and
MICROPY_OPT_MAP_LOOKUP_CACHE.
For example, on a "quiet" Linux x64 environment (i3-5010U @ 2.10GHz) the
change from CACHE_MAP_LOOKUP_IN_BYTECODE, to LOAD_ATTR_FAST_PATH combined
with MAP_LOOKUP_CACHE is:
diff of scores (higher is better)
N=2000 M=2000 bccache -> attrmapcache diff diff% (error%)
bm_chaos.py 13742.56 -> 13905.67 : +163.11 = +1.187% (+/-3.75%)
bm_fannkuch.py 60.13 -> 61.34 : +1.21 = +2.012% (+/-2.11%)
bm_fft.py 113083.20 -> 114793.68 : +1710.48 = +1.513% (+/-1.57%)
bm_float.py 256552.80 -> 243908.29 : -12644.51 = -4.929% (+/-1.90%)
bm_hexiom.py 521.93 -> 625.41 : +103.48 = +19.826% (+/-0.40%)
bm_nqueens.py 197544.25 -> 217713.12 : +20168.87 = +10.210% (+/-3.01%)
bm_pidigits.py 8072.98 -> 8198.75 : +125.77 = +1.558% (+/-3.22%)
misc_aes.py 17283.45 -> 16480.52 : -802.93 = -4.646% (+/-0.82%)
misc_mandel.py 99083.99 -> 128939.84 : +29855.85 = +30.132% (+/-5.88%)
misc_pystone.py 83860.10 -> 82592.56 : -1267.54 = -1.511% (+/-2.27%)
misc_raytrace.py 21490.40 -> 22227.23 : +736.83 = +3.429% (+/-1.88%)
This shows that the new optimisations are at least as good as the existing
inline-bytecode-caching, and are sometimes much better (because the new
ones apply caching to a wider variety of map lookups).
The new optimisations can also benefit code generated by the native
emitter, because they apply to the runtime rather than the generated code.
The improvement for the native emitter when LOAD_ATTR_FAST_PATH and
MAP_LOOKUP_CACHE are enabled is (same Linux environment as above):
diff of scores (higher is better)
N=2000 M=2000 native -> nat-attrmapcache diff diff% (error%)
bm_chaos.py 14130.62 -> 15464.68 : +1334.06 = +9.441% (+/-7.11%)
bm_fannkuch.py 74.96 -> 76.16 : +1.20 = +1.601% (+/-1.80%)
bm_fft.py 166682.99 -> 168221.86 : +1538.87 = +0.923% (+/-4.20%)
bm_float.py 233415.23 -> 265524.90 : +32109.67 = +13.756% (+/-2.57%)
bm_hexiom.py 628.59 -> 734.17 : +105.58 = +16.796% (+/-1.39%)
bm_nqueens.py 225418.44 -> 232926.45 : +7508.01 = +3.331% (+/-3.10%)
bm_pidigits.py 6322.00 -> 6379.52 : +57.52 = +0.910% (+/-5.62%)
misc_aes.py 20670.10 -> 27223.18 : +6553.08 = +31.703% (+/-1.56%)
misc_mandel.py 138221.11 -> 152014.01 : +13792.90 = +9.979% (+/-2.46%)
misc_pystone.py 85032.14 -> 105681.44 : +20649.30 = +24.284% (+/-2.25%)
misc_raytrace.py 19800.01 -> 23350.73 : +3550.72 = +17.933% (+/-2.79%)
In summary, compared to MICROPY_OPT_CACHE_MAP_LOOKUP_IN_BYTECODE, the new
MICROPY_OPT_LOAD_ATTR_FAST_PATH and MICROPY_OPT_MAP_LOOKUP_CACHE options:
- are simpler;
- take less code size;
- are faster (generally);
- work with code generated by the native emitter;
- can be used on embedded targets with a small and constant RAM overhead;
- allow the same .mpy bytecode to run on all targets.
See #7680 for further discussion. And see also #7653 for a discussion
about simplifying mpy-cross options.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
When the LOAD_ATTR opcode is executed there are quite a few different cases
that have to be handled, but the common case is accessing a member on an
instance type. Typically, built-in types provide methods which is why this
is common.
Fortunately, for this specific case, if the member is found in the member
map then there's no further processing.
This optimisation does a relatively cheap check (type is instance) and then
forwards directly to the member map lookup, falling back to the regular
path if necessary.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Fixes the following (the line numbers match commit 0e87459e2b):
../../extmod/crypto-algorithms/sha256.c:49:19: runtime error: left shif...
../../extmod/moduasyncio.c:106:35: runtime error: member access within ...
../../py/binary.c:210:13: runtime error: left shift of negative value -...
../../py/mpz.c:744:16: runtime error: negation of -9223372036854775808 ...
../../py/objint.c:109:22: runtime error: left shift of 1 by 31 places c...
../../py/objint_mpz.c:374:9: runtime error: left shift of 4611686018427...
../../py/objint_mpz.c:374:9: runtime error: left shift of negative valu...
../../py/parsenum.c:106:14: runtime error: left shift of 46116860184273...
../../py/runtime.c:395:33: runtime error: left shift of negative value ...
../../py/showbc.c:177:28: runtime error: left shift of negative value -...
../../py/vm.c:321:36: runtime error: left shift of negative value -1```
Testing was done on an amd64 Debian Buster system using gcc-8.3 and these
settings:
CFLAGS += -g3 -Og -fsanitize=undefined
LDFLAGS += -fsanitize=undefined
The introduced TASK_PAIRHEAP macro's conditional (x ? &x->i : NULL)
assembles (under amd64 gcc 8.3 -Os) to the same as &x->i, since i is the
initial field of the struct. However, for the purposes of undefined
behavior analysis the conditional is needed.
Signed-off-by: Jeff Epler <jepler@gmail.com>
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
mp_printf should be used to print the prefix because it's also used in
mp_bytecode_print2 (otherwise, depending on the system, different output
streams may be used).
Also print the current thread state when threading is enabled to easily see
which thread executes what opcode.
Signed-off-by: Damien George <damien@micropython.org>
Because the atomic section starts after checking whether the scheduler
state is pending, it's possible it can become a different state by the time
the atomic section starts.
This is especially likely on ports where MICROPY_BEGIN_ATOMIC_SECTION is
implemented with a mutex (i.e. it might block), but the race exists
regardless, i.e. if a context switch occurs between those two lines.
This string is recognised by uncrustify, to disable formatting in the
region marked by these comments. This is necessary in the qstrdef*.h files
to prevent modification of the strings within the Q(...). In other places
it is used to prevent excessive reformatting that would make the code less
readable.
Prior to this commit, when unwinding through an active finally the stack
was not being correctly popped/folded, which resulting in the VM crashing
for complicated unwinding of nested finallys.
This should be fixed with this commit, and more tests for return/break/
continue within a finally have been added to exercise this.
This patch compresses the second part of the bytecode prelude which
contains the source file name, function name, source-line-number mapping
and cell closure information. This part of the prelude now begins with a
single varible length unsigned integer which encodes 2 numbers, being the
byte-size of the following 2 sections in the header: the "source info
section" and the "closure section". After decoding this variable unsigned
integer it's possible to skip over one or both of these sections very
easily.
This scheme saves about 2 bytes for most functions compared to the original
format: one in the case that there are no closure cells, and one because
padding was eliminated.
The start of the bytecode prelude contains 6 numbers telling the amount of
stack needed for the Python values and exceptions, and the signature of the
function. Prior to this patch these numbers were all encoded one after the
other (2x variable unsigned integers, then 4x bytes), but using so many
bytes is unnecessary.
An entropy analysis of around 150,000 bytecode functions from the CPython
standard library showed that the optimal Shannon coding would need about
7.1 bits on average to encode these 6 numbers, compared to the existing 48
bits.
This patch attempts to get close to this optimal value by packing the 6
numbers into a single, varible-length unsigned integer via bit-wise
interleaving. The interleaving scheme is chosen to minimise the average
number of bytes needed, and at the same time keep the scheme simple enough
so it can be implemented without too much overhead in code size or speed.
The scheme requires about 10.5 bits on average to store the 6 numbers.
As a result most functions which originally took 6 bytes to encode these 6
numbers now need only 1 byte (in 80% of cases).
From the beginning of this project the RAISE_VARARGS opcode was named and
implemented following CPython, where it has an argument (to the opcode)
counting how many args the raise takes:
raise # 0 args (re-raise previous exception)
raise exc # 1 arg
raise exc from exc2 # 2 args (chained raise)
In the bytecode this operation therefore takes 2 bytes, one for
RAISE_VARARGS and one for the number of args.
This patch splits this opcode into 3, where each is now a single byte.
This reduces bytecode size by 1 byte for each use of raise. Every byte
counts! It also has the benefit of reducing code size (on all ports except
nanbox).
This commit adds support for sys.settrace, allowing to install Python
handlers to trace execution of Python code. The interface follows CPython
as closely as possible. The feature is disabled by default and can be
enabled via MICROPY_PY_SYS_SETTRACE.
With this patch exceptions that are re-raised have improved tracebacks
(less confusing, match CPython), and it makes re-raise slightly more
efficient (in time and RAM) because they no longer need to add a traceback.
Also general VM performance is not measurably affected.
Partially fixes issue #2928.
With this patch exception tracebacks that go through a finally are improved
(less confusing, match CPython), and it makes finally's slightly more
efficient (in time and RAM) because they no longer need to add a traceback.
Partially fixes issue #2928.
It's really an opcode that's not implemented, so use "opcode" instead of
"byte code". And remove the redundant "not implemented" text because that
is already implied by the exception type. There's no need to have a long
error message for an exception that is almost never encountered. Saves
about 20 bytes of code size on most ports.
POP_BLOCK and POP_EXCEPT are now the same, and are always followed by a
JUMP. So this optimisation reduces code size, and RAM usage of bytecode by
two bytes for each try-except handler.
This patch fixes a bug in the VM when breaking within a try-finally. The
bug has to do with executing a break within the finally block of a
try-finally statement. For example:
def f():
for x in (1,):
print('a', x)
try:
raise Exception
finally:
print(1)
break
print('b', x)
f()
Currently in uPy the above code will print:
a 1
1
1
segmentation fault (core dumped) micropython
Not only is there a seg fault, but the "1" in the finally block is printed
twice. This is because when the VM executes a finally block it doesn't
really know if that block was executed due to a fall-through of the try (no
exception raised), or because an exception is active. In particular, for
nested finallys the VM has no idea which of the nested ones have active
exceptions and which are just fall-throughs. So when a break (or continue)
is executed it tries to unwind all of the finallys, when in fact only some
may be active.
It's questionable whether break (or return or continue) should be allowed
within a finally block, because they implicitly swallow any active
exception, but nevertheless it's allowed by CPython (although almost never
used in the standard library). And uPy should at least not crash in such a
case.
The solution here relies on the fact that exception and finally handlers
always appear in the bytecode after the try body.
Note: there was a similar bug with a return in a finally block, but that
was previously fixed in b735208403
These macros could in principle be (inline) functions so it makes sense to
have them lower case, to match the other C API functions.
The remaining macros that are upper case are:
- MP_OBJ_TO_PTR, MP_OBJ_FROM_PTR
- MP_OBJ_NEW_SMALL_INT, MP_OBJ_SMALL_INT_VALUE
- MP_OBJ_NEW_QSTR, MP_OBJ_QSTR_VALUE
- MP_OBJ_FUN_MAKE_SIG
- MP_DECLARE_CONST_xxx
- MP_DEFINE_CONST_xxx
These must remain macros because they are used when defining const data (at
least, MP_OBJ_NEW_SMALL_INT is so it makes sense to have
MP_OBJ_SMALL_INT_VALUE also a macro).
For those macros that have been made lower case, compatibility macros are
provided for the old names so that users do not need to change their code
immediately.
Python defines warnings as belonging to categories, where category is a
warning type (descending from exception type). This is useful, as e.g.
allows to disable warnings selectively and provide user-defined warning
types. So, implement this in MicroPython, except that categories are
represented just with strings. However, enough hooks are left to implement
categories differently per-port (e.g. as types), without need to patch each
and every usage.
Instead of at end of state, n_state - 1. It was originally (way back in
v1.0) put at the end of the state because the VM didn't have a pointer to
the start. But now that the VM takes a mp_code_state_t pointer it does
have a pointer to the start of the state so can put the exception object
there.
This commit saves about 30 bytes of code on all architectures, and, more
importantly, reduces C-stack usage by a couple of words (8 bytes on Thumb2
and 16 bytes on x86-64) for every (non-generator) call of a bytecode
function because fun_bc_call no longer needs to remember the n_state
variable.
mp_make_raise_obj must be used to convert a possible exception type to an
instance object, otherwise the VM may raise a non-exception object.
An existing test is adjusted to test this case, with the original test
already moved to generator_throw.py.
Back in 8047340d75 basic support was added in
the VM to handle return statements within a finally block. But it didn't
cover all cases, in particular when some finally's were active and others
inactive when the "return" was executed.
This patch adds further support for return-within-finally by correctly
managing the currently_in_except_block flag, and should fix all cases. The
main point is that finally handlers remain on the exception stack even if
they are active (currently being executed), and the unwind return code
should only execute those finally's which are inactive.
New tests are added for the cases which now pass.
Before this patch, when using the switch statement for dispatch in the VM
(not computed goto) a pending exception check was done after each opcode.
This is not necessary and this patch makes the pending exception check only
happen when explicitly requested by certain opcodes, like jump. This
improves performance of the VM by about 2.5% when using the switch.
Damien George
David Lechner
Jim Mussared
Jeff Epler
David Lechner
Damien George
Milan Rossa
Paul Sokolovsky