On esp32, the build output consists of:
- micropython.elf
- micropython.map
- micropython.bin -- application only
- micropython.uf2 -- application only
- firmware.bin -- bootloader, partition table and application
Currently everything is available at the download page except
micropython.bin. This commit adds that file but with the extension changed
to .app-bin, to distinguish it from .bin (the full thing).
Signed-off-by: Damien George <damien@micropython.org>
Previous the build directory just used the board name, now make it use the
variant name too.
This shouldn't have any change because the existing directory should not
exist (all builds run by these scripts remove their build directory after
completion), but it makes debugging easier.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Having two separate manifests is confusing. It's simpler to have the daily
builds use the same configuration as the stable, release builds.
Signed-off-by: Damien George <damien@micropython.org>
Rather than having the autobuild know about the particular variants, have
the mpconfigboard.mk describe them and make autobuild discover them
automatically.
Adds a "query-variants" target to stm32/Makefile to allow the set of
possible variants to be queried.
Removes pybv3 from the autobuild as this isn't use by the downloads page.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Any board with a board.json file will be built. ESP32-based boards will be
built using the IDF at $IDF_PATH_V42, all other MCU variants (S2, S3, C3)
will be built using the IDF at $IDF_PATH_V44.
Signed-off-by: Damien George <damien@micropython.org>
Any board with a board.json file will be built. Additional variants for
certain pyboards will also be built by the explicit build-stm32-extra.sh
script. Both .dfu and .hex files will be made available.
Also build boards in a sorted order, and don't stop building if a single
board fails.
Signed-off-by: Damien George <damien@micropython.org>
- Moves definition of BOARD_FLASH_SIZE and other header files related to
flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.
With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.
Signed-off-by: Philipp Ebensberger
And using "-B" means mpy-cross is forcefully rebuilt, sometimes with
invalid CFLAGS_EXTRA options which makes the auto-build fail.
Signed-off-by: Damien George <damien@micropython.org>
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.
The Makefile had to be changed in order to build the .bin file as well.
