Eventually these responses could be filled in by a function to make their
contents dynamic, depending on the attached logical units. But for now
they are fixed, and this patch fixes the MODE SENSE(6) responses so it is
the correct length with the correct header.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
The new compile-time option is MICROPY_HW_USB_MAX_POWER_MA. Set this in
the board configuration file to the maximum current in mA that the board
will draw over USB. The default is 500mA.
The new compile-time option is MICROPY_HW_USB_SELF_POWERED. Set this
option to 1 in the board configuration file to indicate that the USB device
is self powered. This option is disabled by default (previous behaviour).
Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to
regularly check if buffered data needed to be sent out to the USB host.
This wasted resources (CPU, power) if no data needed to be sent.
This commit changes how the USB CDC transmits buffered data:
- When new data is first available to send the data is queued immediately
on the USB IN endpoint, ready to be sent as soon as possible.
- Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait.
- When the low-level USB driver has finished sending out the data queued
in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately
queues any outstanding data, waiting for the next IN frame.
The benefits on this new approach are:
- SOF IRQ does not need to run continuously so device has a better chance
to sleep for longer, and be more responsive to other IRQs.
- Because SOF IRQ is off, current consumption is reduced by a small amount,
roughly 200uA when USB is connected (measured on PYBv1.0).
- CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is
unchanged).
- When USB is connected, Python code that is executing is slightly faster
because SOF IRQ no longer interrupts continuously.
- On F733 with USB HS, CDC tx throughput is about the same as prior to this
commit.
- On F733 with USB HS, Python code is about 5% faster because of no SOF.
As part of this refactor, the serial port should no longer echo initial
characters when the serial port is first opened (this only used to happen
rarely on USB FS, but on USB HS is was more evident).
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC. It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it. The second one is
available for general use.
This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM. Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints. The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
This patch allows to completely compile-out support for USB, and no-USB is
now the default. If a board wants to enable USB it should define:
#define MICROPY_HW_ENABLE_USB (1)
And then one or more of the following to select the USB PHY:
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_HS (1)
#define MICROPY_HW_USB_HS_IN_FS (1)
Prior to this patch the USBD driver did not handle the recipient correctly
for setup requests. It was not interpreting the req->wIndex field in the
right way: in some cases this field indicates the endpoint number but the
code was assuming it always indicated the interface number.
This patch fixes this. The only noticeable change is to the MSC
interface, which should now correctly respond to the USB_REQ_CLEAR_FEATURE
request and hence unmount properly from the host when requested.
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode. To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY. High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.
This patch has been tested on an STM32F733.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
