8c7877298a
31 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Dan Halbert
|
367e13c69f | change CIRCUITPY change markers to CIRCUITPY-CHANGE | ||
|
Dan Halbert
|
c0a4abc03c | Fix merge bugs; remove shared/tinyusb/* | ||
|
Dan Halbert
|
f2ebe6839c | Initial MicroPython v1.21.0 merge; not compiled yet | ||
Scott Shawcroft
|
5a19971efd
|
Fix pre-commit | ||
|
Dan Halbert
|
1c388ab315 | finish converting to MP_REGISTER_ROOT_POINTER() | ||
|
Dan Halbert
|
2c0fa0f7dc | initial merge from v1.20.0; just satisifying conflicts | ||
|
Dan Halbert
|
d582407b06 | pre-commit fixes | ||
|
Dan Halbert
|
2ff8667e75 |
wip; remove long-lived functionality; remove PR#2614
Trinket M0 compile has no compilation errors, but has link errors to fix. |
||
|
Dan Halbert
|
465d1c673e | wip | ||
|
Dan Halbert
|
0d4bc8c163 | initial v1.19.1 merge; not compiled yet | ||
Damien George
|
b1229efbd1 |
all: Fix spelling mistakes based on codespell check.
Signed-off-by: Damien George <damien@micropython.org> |
||
David Grayson
|
c046b23ea2 |
shared/runtime/pyexec: Don't allow Ctrl+C to interrupt frozen boot code.
Helps prevent the filesystem from getting formatted by mistake, among other things. For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many times will eventually wipe the filesystem (without warning or notice). Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote) and UI's (eg Mu, Thonny) to get the board into a known state. If the board is not responding for a short time then it's not possible to know if it's just a slow start up (eg in _boot.py), or an infinite loop in the main application. The former should not be interrupted, but the latter should. The only way to distinguish these two cases would be to wait "long enough", and if there's nothing on the serial after "long enough" then assume it's running the application and Ctrl+C should break out of it. But defining "long enough" is impossible for all the different boards and their possible behaviour. The solution in this commit is to make it so that frozen start-up code cannot be interrupted by Ctrl+C. That code then effectively acts like normal C start-up code, which also cannot be interrupted. Note: on the stm32 port this was never seen as an issue because all start-up code is in C. But now other ports start to put more things in _boot.py and so this problem crops up. Signed-off-by: David Grayson <davidegrayson@gmail.com> |
||
hathach
|
fecc1bdedb
|
fix typos (partial) detected by codepell | ||
|
Damien George
|
b3c8ab37ec |
py/gc: Make gc_dump_info/gc_dump_alloc_table take a printer as argument.
So that callers can redirect the output if needed. Signed-off-by: Damien George <damien@micropython.org> |
||
|
Damien George
|
1978b838b7 |
shared/runtime: Use mp_printf consistently, instead of printf.
Signed-off-by: Damien George <damien@micropython.org> |
||
|
Dan Halbert
|
60f43b1703 | allow preserving pin state during deep sleep | ||
|
Scott Shawcroft
|
86f4014f83
|
Add exception filename to title bar
Add the exception filename after the line number and change the line number so it is in that file. It used to always be code.py. Fixes #6702 |
||
David Lechner
|
68f46342aa |
shared/runtime/pyexec: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register repl_line instead of using a conditional inside of mp_state_vm_t. Signed-off-by: David Lechner <david@pybricks.com> |
||
|
Damien George
|
402df833fe |
py/modsys: Introduce sys.implementation._machine constant.
This contains a string useful for identifying the underlying machine. This string is kept consistent with the second part of the REPL banner via the new config option MICROPY_BANNER_MACHINE. This makes os.uname() more or less redundant, as all the information in os.uname() is now available in the sys module. Signed-off-by: Damien George <damien@micropython.org> |
||
|
Damien George
|
40047823bc |
py/modsys: Append MicroPython git version and build date to sys.version.
This commit adds the git hash and build date to sys.version. This is
allowed according to CPython docs, and is what PyPy does. The docs state:
A string containing the version number of the Python interpreter plus
additional information on the build number and compiler used.
Eg on CPython:
Python 3.10.4 (main, Mar 23 2022, 23:05:40) [GCC 11.2.0] on linux
Type "help", "copyright", "credits" or "license" for more information.
>>> import sys
>>> sys.version
'3.10.4 (main, Mar 23 2022, 23:05:40) [GCC 11.2.0]'
and PyPy:
Python 2.7.12 (5.6.0+dfsg-4, Nov 20 2016, 10:43:30)
[PyPy 5.6.0 with GCC 6.2.0 20161109] on linux2
Type "help", "copyright", "credits" or "license" for more information.
>>>> import sys
>>>> sys.version
'2.7.12 (5.6.0+dfsg-4, Nov 20 2016, 10:43:30)\n[PyPy 5.6.0 with GCC ...
With this commit on MicroPython we now have:
MicroPython v1.18-371-g9d08eb024 on 2022-04-28; linux [GCC 11.2.0] v...
Use Ctrl-D to exit, Ctrl-E for paste mode
>>> import sys
>>> sys.version
'3.4.0; MicroPython v1.18-371-g9d08eb024 on 2022-04-28'
Note that the start of the banner is the same as the end of sys.version.
This helps to keep code size under control because the string can be reused
by the compiler.
Signed-off-by: Damien George <damien@micropython.org>
|
||
|
Scott Shawcroft
|
dcc3ec171e
|
Merge remote-tracking branch 'adafruit/7.2.x' into merge_7.2.2 | ||
|
Damien George
|
ac2293161e |
py/modsys: Add optional mutable attributes sys.ps1/ps2 and use them.
This allows customising the REPL prompt strings. Signed-off-by: Damien George <damien@micropython.org> |
||
|
Dan Halbert
|
9b2e22a6df |
Make autoreload checking more robust
- Add reset for autoreload. De-request ticks. - Separate state a little more in autoreload.c - Rename some routines. - Remove redundant settings of CIRCUITPY_AUTORELOAD_DELAY_MS. |
||
|
Damien George
|
f2040bfc7e |
py: Rework bytecode and .mpy file format to be mostly static data.
Background: .mpy files are precompiled .py files, built using mpy-cross,
that contain compiled bytecode functions (and can also contain machine
code). The benefit of using an .mpy file over a .py file is that they are
faster to import and take less memory when importing. They are also
smaller on disk.
But the real benefit of .mpy files comes when they are frozen into the
firmware. This is done by loading the .mpy file during compilation of the
firmware and turning it into a set of big C data structures (the job of
mpy-tool.py), which are then compiled and downloaded into the ROM of a
device. These C data structures can be executed in-place, ie directly from
ROM. This makes importing even faster because there is very little to do,
and also means such frozen modules take up much less RAM (because their
bytecode stays in ROM).
The downside of frozen code is that it requires recompiling and reflashing
the entire firmware. This can be a big barrier to entry, slows down
development time, and makes it harder to do OTA updates of frozen code
(because the whole firmware must be updated).
This commit attempts to solve this problem by providing a solution that
sits between loading .mpy files into RAM and freezing them into the
firmware. The .mpy file format has been reworked so that it consists of
data and bytecode which is mostly static and ready to run in-place. If
these new .mpy files are located in flash/ROM which is memory addressable,
the .mpy file can be executed (mostly) in-place.
With this approach there is still a small amount of unpacking and linking
of the .mpy file that needs to be done when it's imported, but it's still
much better than loading an .mpy from disk into RAM (although not as good
as freezing .mpy files into the firmware).
The main trick to make static .mpy files is to adjust the bytecode so any
qstrs that it references now go through a lookup table to convert from
local qstr number in the module to global qstr number in the firmware.
That means the bytecode does not need linking/rewriting of qstrs when it's
loaded. Instead only a small qstr table needs to be built (and put in RAM)
at import time. This means the bytecode itself is static/constant and can
be used directly if it's in addressable memory. Also the qstr string data
in the .mpy file, and some constant object data, can be used directly.
Note that the qstr table is global to the module (ie not per function).
In more detail, in the VM what used to be (schematically):
qst = DECODE_QSTR_VALUE;
is now (schematically):
idx = DECODE_QSTR_INDEX;
qst = qstr_table[idx];
That allows the bytecode to be fixed at compile time and not need
relinking/rewriting of the qstr values. Only qstr_table needs to be linked
when the .mpy is loaded.
Incidentally, this helps to reduce the size of bytecode because what used
to be 2-byte qstr values in the bytecode are now (mostly) 1-byte indices.
If the module uses the same qstr more than two times then the bytecode is
smaller than before.
The following changes are measured for this commit compared to the
previous (the baseline):
- average 7%-9% reduction in size of .mpy files
- frozen code size is reduced by about 5%-7%
- importing .py files uses about 5% less RAM in total
- importing .mpy files uses about 4% less RAM in total
- importing .py and .mpy files takes about the same time as before
The qstr indirection in the bytecode has only a small impact on VM
performance. For stm32 on PYBv1.0 the performance change of this commit
is:
diff of scores (higher is better)
N=100 M=100 baseline -> this-commit diff diff% (error%)
bm_chaos.py 371.07 -> 357.39 : -13.68 = -3.687% (+/-0.02%)
bm_fannkuch.py 78.72 -> 77.49 : -1.23 = -1.563% (+/-0.01%)
bm_fft.py 2591.73 -> 2539.28 : -52.45 = -2.024% (+/-0.00%)
bm_float.py 6034.93 -> 5908.30 : -126.63 = -2.098% (+/-0.01%)
bm_hexiom.py 48.96 -> 47.93 : -1.03 = -2.104% (+/-0.00%)
bm_nqueens.py 4510.63 -> 4459.94 : -50.69 = -1.124% (+/-0.00%)
bm_pidigits.py 650.28 -> 644.96 : -5.32 = -0.818% (+/-0.23%)
core_import_mpy_multi.py 564.77 -> 581.49 : +16.72 = +2.960% (+/-0.01%)
core_import_mpy_single.py 68.67 -> 67.16 : -1.51 = -2.199% (+/-0.01%)
core_qstr.py 64.16 -> 64.12 : -0.04 = -0.062% (+/-0.00%)
core_yield_from.py 362.58 -> 354.50 : -8.08 = -2.228% (+/-0.00%)
misc_aes.py 429.69 -> 405.59 : -24.10 = -5.609% (+/-0.01%)
misc_mandel.py 3485.13 -> 3416.51 : -68.62 = -1.969% (+/-0.00%)
misc_pystone.py 2496.53 -> 2405.56 : -90.97 = -3.644% (+/-0.01%)
misc_raytrace.py 381.47 -> 374.01 : -7.46 = -1.956% (+/-0.01%)
viper_call0.py 576.73 -> 572.49 : -4.24 = -0.735% (+/-0.04%)
viper_call1a.py 550.37 -> 546.21 : -4.16 = -0.756% (+/-0.09%)
viper_call1b.py 438.23 -> 435.68 : -2.55 = -0.582% (+/-0.06%)
viper_call1c.py 442.84 -> 440.04 : -2.80 = -0.632% (+/-0.08%)
viper_call2a.py 536.31 -> 532.35 : -3.96 = -0.738% (+/-0.06%)
viper_call2b.py 382.34 -> 377.07 : -5.27 = -1.378% (+/-0.03%)
And for unix on x64:
diff of scores (higher is better)
N=2000 M=2000 baseline -> this-commit diff diff% (error%)
bm_chaos.py 13594.20 -> 13073.84 : -520.36 = -3.828% (+/-5.44%)
bm_fannkuch.py 60.63 -> 59.58 : -1.05 = -1.732% (+/-3.01%)
bm_fft.py 112009.15 -> 111603.32 : -405.83 = -0.362% (+/-4.03%)
bm_float.py 246202.55 -> 247923.81 : +1721.26 = +0.699% (+/-2.79%)
bm_hexiom.py 615.65 -> 617.21 : +1.56 = +0.253% (+/-1.64%)
bm_nqueens.py 215807.95 -> 215600.96 : -206.99 = -0.096% (+/-3.52%)
bm_pidigits.py 8246.74 -> 8422.82 : +176.08 = +2.135% (+/-3.64%)
misc_aes.py 16133.00 -> 16452.74 : +319.74 = +1.982% (+/-1.50%)
misc_mandel.py 128146.69 -> 130796.43 : +2649.74 = +2.068% (+/-3.18%)
misc_pystone.py 83811.49 -> 83124.85 : -686.64 = -0.819% (+/-1.03%)
misc_raytrace.py 21688.02 -> 21385.10 : -302.92 = -1.397% (+/-3.20%)
The code size change is (firmware with a lot of frozen code benefits the
most):
bare-arm: +396 +0.697%
minimal x86: +1595 +0.979% [incl +32(data)]
unix x64: +2408 +0.470% [incl +800(data)]
unix nanbox: +1396 +0.309% [incl -96(data)]
stm32: -1256 -0.318% PYBV10
cc3200: +288 +0.157%
esp8266: -260 -0.037% GENERIC
esp32: -216 -0.014% GENERIC[incl -1072(data)]
nrf: +116 +0.067% pca10040
rp2: -664 -0.135% PICO
samd: +844 +0.607% ADAFRUIT_ITSYBITSY_M4_EXPRESS
As part of this change the .mpy file format version is bumped to version 6.
And mpy-tool.py has been improved to provide a good visualisation of the
contents of .mpy files.
In summary: this commit changes the bytecode to use qstr indirection, and
reworks the .mpy file format to be simpler and allow .mpy files to be
executed in-place. Performance is not impacted too much. Eventually it
will be possible to store such .mpy files in a linear, read-only, memory-
mappable filesystem so they can be executed from flash/ROM. This will
essentially be able to replace frozen code for most applications.
Signed-off-by: Damien George <damien@micropython.org>
|
||
Jeff Epler
|
01cabb0324 |
Merge tag 'v1.18'
Boosted performance, board.json metadata, more mimxrt, rp2, samd features
This release of MicroPython sees a boost to the overall performance of the
VM and runtime. This is achieved by the addition of an optional cache to
speed up general hash table lookups, as well as a fast path in the VM for
the LOAD_ATTR opcode on instance types. The new configuration options are
MICROPY_OPT_MAP_LOOKUP_CACHE and MICROPY_OPT_LOAD_ATTR_FAST_PATH. As part
of this improvement the MICROPY_OPT_CACHE_MAP_LOOKUP_IN_BYTECODE option has
been removed, which provided a similar map caching mechanism but with the
cache stored in the bytecode, which made it not useful on bare metal ports.
The new mechanism is measured to be at least as good as the old one,
applies to more map lookups, has a constant RAM overhead, and applies to
native code as well as bytecode.
These performance options are enabled on the esp32, mimxrt, rp2, stm32 and
unix ports. For esp32 and mimxrt some code is also moved to RAM to further
boost performance. On stm32, performance increases by about 20% for
benchmarks that are heavy on name lookups, like misc_pystone.py and
misc_raytrace.py. On esp32 performance can increase by 2-3x, and on mimxrt
it is up to 6x.
All boards in all ports now have a board.json metadata file, which is used
to automatically build firmware and generate a webpage for that board
(among other possibilities). Auto-build scripts have been added for this
purpose and they build all esp32, mimxrt, rp2, samd and stm32 boards. The
generated output is available at https://micropython.org/download.
Support for FROZEN_DIR and FROZEN_MPY_DIR has been deprecated for some time
and was finally removed in this release. Instead of these, FROZEN_MANIFEST
can be used. The io.resource_stream() function is also removed, replaced
by the pure Python version in micropython-lib.
The search order for importing frozen Python modules is now controlled by
the ".frozen" entry in sys.path. This string is added by default in the
second position in sys.path. User code should adjust sys.path depending on
the desired behaviour. Putting ".frozen" first in sys.path will speed up
importing frozen modules.
A bug in multiple precision integers with bitwise of -0 was fixed in commit
|
||
iabdalkader
|
644f4dcc94 |
shared/runtime/pyexec: Cleanup EXEC_FLAG flag constants.
- Cleanup pyexec flags definitions so it's clear they are different. - Use mp_uint_t for exec_flags because it should be unsigned. |
||
Jim Mussared
|
e0bf4611c3 |
py: Only search frozen modules when '.frozen' is found in sys.path.
This changes makemanifest.py & mpy-tool.py to merge string and mpy names into the same list (now mp_frozen_names). The various paths for loading a frozen module (mp_find_frozen_module) and checking existence of a frozen module (mp_frozen_stat) use a common function that searches this list. In addition, the frozen lookup will now only take place if the path starts with ".frozen", which needs to be added to sys.path. This fixes issues #1804, #2322, #3509, #6419. Signed-off-by: Jim Mussared <jim.mussared@gmail.com> |
||
Timon
|
a1052d5f73
|
Initial broadcom port for Raspberry Pi
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4 and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes outside of the ports directory for it. There are a couple other cleanups that were incidental: * Use const mcu_pin_obj_t instead of omitting the const. The structs themselves are const because they are in ROM. * Use PTR <-> OBJ conversions in more places. They were found when mp_obj_t was set to an integer type rather than pointer. * Optimize submodule checkout because the Pi submodules are heavy and unnecessary for the vast majority of builds. Fixes #4314 |
||
Jeff Epler
|
8d8f83bc05 |
Merge tag 'v1.17' into merge-1.17
F-strings, new machine.I2S class, ESP32-C3 support and LEGO_HUB_NO6 board
This release of MicroPython adds support for f-strings (PEP-498), with a
few limitations compared to normal Python. F-strings are essentially
syntactic sugar for "".format() and make formatting strings a lot more
convenient. Other improvements to the core runtime include pretty printing
OSError when it has two arguments (an errno code and a string), scheduling
of KeyboardInterrupt on the main thread, and support for a single argument
to the optimised form of StopIteration.
In the machine module a new I2S class has been added, with support for
esp32 and stm32 ports. This provides a consistent API for transmit and
receive of audio data in blocking, non-blocking and asyncio-based
operation. Also, the json module has support for the "separators" argument
in the dump and dumps functions, and framebuf now includes a way to blit
between frame buffers of different formats using a palette. A new,
portable machine.bitstream function is also added which can output a stream
of bits with configurable timing, and is used as the basis for driving
WS2812 LEDs in a common way across ports.
There has been some restructuring of the repository directory layout, with
all third-party code now in the lib/ directory. And a new top-level
directory shared/ has been added with first-party code that was previously
in lib/ moved there.
The docs have seen further improvement with enhancements and additions to
the rp2 parts, as well as a new quick reference for the zephyr port.
The terms master/slave have been replaced with controller/peripheral,
mainly relating to I2C and SPI usage. And u-module references have been
replaced with just the module name without the u-prefix to help clear up
the intended usage of modules in MicroPython.
For the esp8266 and esp32 ports, hidden networks are now included in WLAN
scan results. On the esp32 the RMT class is enhanced with idle_level and
write_pulses modes. There is initial support for ESP32-C3 chips with
GENERIC_C3 and GENERIC_C3_USB boards.
The javascript port has had its Makefile and garbage collector
implementation reworked so it compiles and runs with latest the Emscripten
using asyncify.
The mimxrt port sees the addition of hardware I2C and SPI support, as well
as some additional methods to the machine module. There is also support
for Hyperflash chips.
The nrf port now has full VFS storage support, enables source-line on
traceback, and has .mpy features consistent with other ports.
For the rp2 port there is now more configurability for boards, and more
boards added.
The stm32 port has a new LEGO_HUB_NO6 board definition with detailed
information how to get this LEGO Hub running stock MicroPython. There is
also now support to change the CPU frequency on STM32WB MCUs. And USBD_xxx
descriptor options have been renamed to MICROPY_HW_USB_xxx.
Thanks to everyone who contributed to this release: Amir Gonnen, Andrew
Scheller, Bryan Tong Minh, Chris Wilson, Damien George, Daniel Mizyrycki,
David Lechner, David P, Fernando, finefoot, Frank Pilhofer, Glenn Ruben
Bakke, iabdalkader, Jeff Epler, Jim Mussared, Jonathan Hogg, Josh Klar,
Josh Lloyd, Julia Hathaway, Krzysztof Adamski, Matúš Olekšák, Michael
Weiss, Michel Bouwmans, Mike Causer, Mike Teachman, Ned Konz, NitiKaur,
oclyke, Patrick Van Oosterwijck, Peter Hinch, Peter Züger, Philipp
Ebensberger, robert-hh, Roberto Colistete Jr, Sashkoiv, Seon Rozenblum,
Tobias Thyrrestrup, Tom McDermott, Will Sowerbutts, Yonatan Goldschmidt.
What follows is a detailed list of changes, generated from the git commit
history, and organised into sections.
Main components
===============
all:
- fix signed shifts and NULL access errors from -fsanitize=undefined
- update to point to files in new shared/ directory
py core:
- mpstate: make exceptions thread-local
- mpstate: schedule KeyboardInterrupt on main thread
- mperrno: add MP_ECANCELED error code
- makeqstrdefs.py: don't include .h files explicitly in preprocessing
- mark unused arguments from bytecode decoding macros
- objexcept: pretty print OSError also when it has 2 arguments
- makeversionhdr: add --tags arg to git describe
- vm: simplify handling of MP_OBJ_STOP_ITERATION in yield-from opcode
- objexcept: make mp_obj_exception_get_value support subclassed excs
- support single argument to optimised MP_OBJ_STOP_ITERATION
- introduce and use mp_raise_type_arg helper
- modsys: optimise sys.exit for code size by using exception helpers
- objexcept: make mp_obj_new_exception_arg1 inline
- obj: fix formatting of comment for mp_obj_is_integer
- emitnative: reuse need_reg_all func in need_stack_settled
- emitnative: ensure stack settling is safe mid-branch
- runtime: fix bool unary op for subclasses of native types
- builtinimport: fix condition for including do_execute_raw_code()
- mkrules: automatically build mpy-cross if it doesn't exist
- implement partial PEP-498 (f-string) support
- lexer: clear fstring_args vstr on lexer free
- mkrules.mk: do submodule sync in "make submodules"
extmod:
- btstack: add missing call to mp_bluetooth_hci_uart_deinit
- btstack: check that BLE is active before performing operations
- uasyncio: get addr and bind server socket before creating task
- axtls-include: add axtls_os_port.h to customise axTLS
- update for move of crypto-algorithms, re1.5, uzlib to lib
- moduselect: conditionally compile select()
- nimble: fix leak in l2cap_send if send-while-stalled
- btstack/btstack.mk: use -Wno-implicit-fallthrough, not =0
- utime: always invoke mp_hal_delay_ms when >= to 0ms
- modbluetooth: clamp MTU values to 32->UINT16_MAX
- nimble: allow modbluetooth binding to hook "sent HCI packet"
- nimble: add "memory stalling" mechanism for l2cap_send
- uasyncio: in open_connection use address info in socket creation
- modujson: add support for dump/dumps separators keyword-argument
- modlwip: fix close and clean up of UDP and raw sockets
- modbluetooth: add send_update arg to gatts_write
- add machine.bitstream
- modframebuf: enable blit between different formats via a palette
lib:
- tinyusb: update to version 0.10.1
- pico-sdk: update to version 1.2.0
- utils/stdout_helpers: make mp_hal_stdout_tx_strn_cooked efficient
- axtls: switch to repo at micropython/axtls
- axtls: update to latest axtls 2.1.5 wih additional commits
- re1.5: move re1.5 code from extmod to lib
- uzlib: move uzlib code from extmod to lib
- crypto-algorithms: move crypto-algorithms code from extmod to lib
- update README's based on contents of these dirs
drivers:
- neopixel: add common machine.bitstream-based neopixel module
- neopixel: optimize fill() for speed
- neopixel: reduce code size of driver
- cyw43: fix cyw43_deinit so it can be called many times in a row
- cyw43: make wifi join fail if interface is not active
mpy-cross:
- disable stack check when building with Emscripten
Support components
==================
docs:
- library: document new esp32.RMT features and fix wait_done
- library: warn that ustruct doesn't handle spaces in format strings
- esp8266/tutorial: change flash mode from dio to dout
- replace master/slave with controller/peripheral in I2C and SPI
- rp2: enhance quickref and change image to Pico pinout
- rp2: update general section to give a brief technical overview
- library/utime.rst: clarify behaviour and precision of sleep ms/us
- library/uasyncio.rst: document stream readexactly() method
- library/machine.I2S.rst: fix use of sd pin in examples
- zephyr: add quick reference for the Zephyr port
- library/zephyr: add libraries specific to the Zephyr port
- templates: add unix and zephyr quickref links to top-index
- rename ufoo.rst to foo.rst
- replace ufoo with foo in all docs
- library/index.rst: clarify module naming and purpose
- library/builtins.rst: add module title
- library/network.rst: simplify socket import
- add docs for machine.bitstream and neopixel module
- library: fix usage of :term: for frozen module reference
- esp8266: use monospace for software tools
- reference: mention that slicing a memoryview causes allocation
examples: no changes specific to this component/port
tests:
- extmod: make uasyncio_heaplock test more deterministic
- cpydiff/modules_struct_whitespace_in_format: run black
- extmod/ujson: add tests for dump/dumps separators argument
- run-multitests.py: add broadcast and wait facility
- multi_bluetooth/ble_subscribe.py: add test for subscription
- extmod/vfs_fat_finaliser.py: ensure alloc at never-used GC blocks
- basics: split f-string debug printing to separate file with .exp
- pybnative: make while.py test run on boards without pyb.delay
tools:
- autobuild: add scripts to build release firmware
- remove obsolete build-stm-latest.sh script
- ci.sh: run apt-get update in ci_powerpc_setup
- makemanifest.py: allow passing flags to mpy-tool.py
- autobuild: add mimxrt port to build scripts for nightly builds
- pyboard.py: add cmd-line option to make soft reset configurable
- mpremote: swap order of PID and VID in connect-list output
- ci.sh: build unix dev variant as part of macOS CI
- ci.sh: build GENERIC_C3 board as part of esp32 CI
- autobuild: use separate IDF version to build newer esp32 SoCs
- autobuild: add FeatherS2 and TinyS2 to esp32 auto builds
- mpremote: add seek whence for mounted files
- mpremote: raise OSError on unsupported RemoteFile.seek
- autobuild: add the MIMXRT1050_EVKB board to the daily builds
- ci.sh: add mpy-cross build to nrf port
- codeformat.py: include ports/nrf/modules/nrf in code formatting
- gen-cpydiff.py: don't rename foo to ufoo in diff output
- autobuild: add auto build for Silicognition wESP32
- mpremote: fix connect-list in case VID/PID are None
- mpremote: add "devs" shortcut for "connect list"
- mpremote: remove support for pyb.USB_VCP in/out specialisation
- autobuild: don't use "-B" for make, it's already a fresh build
- pyboard.py: move --no-exclusive/--soft-reset out of mutex group
- pyboard.py: make --no-follow use same variable as --follow
- pyboard.py: add --exclusive to match --no-exclusive
- pyboard.py: make --no-soft-reset consistent with other args
- uncrustify: force 1 newline at end of file
- mpremote: bump version to 0.0.6
CI:
- workflows: add workflow to build and test javascript port
- workflows: switch from Coveralls to Codecov
- workflows: switch from lcov to gcov
- workflows: add workflow to build and test unix dev variant
The ports
=========
all ports:
- use common mp_hal_stdout_tx_strn_cooked instead of custom one
- update for move of crypto-algorithms, uzlib to lib
- rename USBD_VID/PID config macros to MICROPY_HW_USB_VID/PID
bare-arm port: no changes specific to this component/port
cc3200 port: no changes specific to this component/port
esp8266 port:
- add __len__ to NeoPixel driver to support iterating
- Makefile: add more libm files to build
- include hidden networks in WLAN.scan results
- replace esp.neopixel with machine.bitstream
- remove dead code for end_ticks in machine_bitstream
esp32 port:
- boards/sdkconfig.base: disable MEMPROT_FEATURE to alloc from IRAM
- add __len__ to NeoPixel driver to support iterating
- main: allow MICROPY_DIR to be overridden
- esp32_rmt: fix RMT looping in newer IDF versions
- esp32_rmt: enhance RMT with idle_level and write_pulses modes
- add new machine.I2S class for I2S protocol support
- machine_spi: calculate actual attained baudrate
- machine_hw_spi: use a 2 item SPI queue for long transfers
- machine_dac: add MICROPY_PY_MACHINE_DAC option, enable by default
- machine_i2s: add MICROPY_PY_MACHINE_I2S option, enable by default
- fix use of mp_int_t, size_t and uintptr_t
- add initial support for ESP32C3 SoCs
- boards/GENERIC_C3: add generic C3-based board
- modmachine: release the GIL in machine.idle()
- mphalport: always yield at least once in delay_ms
- machine_uart: add flow kw-arg to enable hardware flow control
- boards: add Silicognition wESP32 board configuration
- mpconfigport.h: enable reverse and inplace special methods
- include hidden networks in WLAN.scan results
- makeimg.py: get bootloader and partition offset from sdkconfig
- enable MICROPY_PY_FSTRINGS by default
- machine_hw_spi: release GIL during transfers
- machine_pin: make check for non-output pins respect chip variant
- replace esp.neopixel with machine.bitstream
- remove dead code for end_ticks in machine_bitstream
- boards: add GENERIC_C3_USB board with USB serial/JTAG support
javascript port:
- rework Makefile and GC so it works with latest Emscripten
- Makefile: suppress compiler errors from array bounds
- Makefile: change variable to EXPORTED_RUNTIME_METHODS
mimxrt port:
- move calc_weekday helper function to timeutils
- machine_spi: add the SPI class to the machine module
- moduos: seed the PRNG on boot using the TRNG
- boards: set vfs partition start to 1 MBbyte
- main: skip running main.py if boot.py failed
- main: extend the information returned by help()
- mimxrt_flash: remove commented-out code
- modmachine: add a few minor methods to the machine module
- machine_led: use mp_raise_msg_varg helper
- machine_i2c: add hardware-based machine.I2C to machine module
- add support for Hyperflash chips
- boards: add support for the MIMXRT1050_EVKB board
- machine_pin: implement ioctl for Pin
minimal port:
- Makefile: add support for building with user C modules
nrf port:
- modules: replace master/slave with controller/peripheral in SPI
- boards/common.ld: calculate unused flash region
- modules/nrf: add new nrf module with flash block device
- drivers: add support for using flash block device with SoftDevice
- mpconfigport.h: expose nrf module when MICROPY_PY_NRF is set
- README: update README.md to reflect internal file systems
- mpconfigport.h: tune FAT FS configuration
- Makefile: add _fs_size linker script override from make
- modules/uos: allow a board to configure MICROPY_VFS_FAT/LFS1/LFS2
- mpconfigport.h: enable MICROPY_PY_IO_FILEIO when an FS is enabled
- qstrdefsport.h: add entries for in-built FS mount points
- main: add auto mount and auto format hook for internal flash FS
- boards: enable needed features for FAT/LFS1/LFS2
- facilitate use of freeze manifest
- boards: set FROZEN_MANIFEST blank when SD present on nrf51 targets
- modules/scripts: add file system formatting script
- Makefile: set default manifest file for all targets
- mphalport: add dummy function for mp_hal_time_ns()
- boards: enable MICROPY_VFS_LFS2 for all target boards
- modules/uos: add ilistdir to uos module
- modules/nrf: add function to enable/disable DCDC
- enable source line on tracebacks
- set .mpy features consistent with documentation and other ports
pic16bit port: no changes specific to this component/port
powerpc port: no changes specific to this component/port
qemu-arm port: no changes specific to this component/port
rp2 port:
- use 0=Monday datetime convention in RTC
- machine_rtc: in RTC.datetime, compute weekday automatically
- CMakeLists.txt: suppress compiler errors for pico-sdk and tinyusb
- tusb_config.h: set CFG_TUD_CDC_EP_BUFSIZE to 256
- machine_uart: add hardware flow control support
- machine_uart: allow overriding default machine UART pins
- machine_i2c: allow boards to configure I2C pins using new macros
- machine_spi: allow boards to configure SPI pins using new macros
- machine_uart: fix poll ioctl to also check hardware FIFO
- machine_uart: fix read when FIFO has chars but ringbuf doesn't
- tusb_port: allow boards to configure USB VID and PID
- boards/ADAFRUIT_FEATHER_RP2040: configure custom VID/PID
- boards/ADAFRUIT_FEATHER_RP2040: configure I2C/SPI default pins
- boards/SPARKFUN_PROMICRO: configure UART/I2C/SPI default pins
- boards/SPARKFUN_THINGPLUS: configure I2C/SPI default pins
- boards: add Adafruit ItsyBitsy RP2040
- boards: add Adafruit QT Py RP2040
- boards: add Pimoroni Pico LiPo 4MB
- boards: add Pimoroni Pico LiPo 16MB
- boards: add Pimoroni Tiny 2040
- CMakeLists.txt: allow a board's cmake to set the manifest path
- enable MICROPY_PY_FSTRINGS by default
- Makefile: add "submodules" target, to match other ports
- rp2_flash: disable IRQs while calling flash_erase/program
- CMakeLists.txt: add option to enable double tap reset to bootrom
- mpconfigport.h: allow boards to add root pointers
samd port:
- add support for building with user C modules
stm32 port:
- softtimer: add soft_timer_reinsert() helper function
- mpbthciport: change from systick to soft-timer for BT scheduling
- provide a custom BTstack runloop that integrates with soft timer
- usb: make irq's default trigger enable all events
- boardctrl: skip running main.py if boot.py had an error
- sdio: fix undefined reference to DMA stream on H7
- dma: add DMAMUX configuration for H7 to fix dma_nohal_init
- main: call mp_deinit() at end of main
- adc: allow using ADC12 and ADC3 for H7
- adc: define the ADC instance used for internal channels
- adc: simplify and generalise how pin_adcX table is defined
- add new machine.I2S class for I2S protocol support
- boards/NUCLEO_F446RE: fix I2C1 pin assignment to match datasheet
- replace master/slave with controller/peripheral in I2C and SPI
- systick: always POLL_HOOK when delaying for milliseconds
- sdram: make SDRAM test cache aware, and optional failure with msg
- boards/NUCLEO_F446RE: enable CAN bus support
- boards: add support for SparkFun STM32 MicroMod Processor board
- uart: fix LPUART1 baudrate set/get
- uart: support low baudrates on LPUART1
- boards/STM32F429DISC: set correct UART2 pins and add UART3/6
- boards/NUCLEO_F439ZI: add board definition for NUCLEO_F439ZI
- boards/LEGO_HUB_NO6: add board definition for LEGO_HUB_NO6
- Makefile: update to only pull in used Bluetooth library
- README.md: update supported MCUs, and submodule and mboot use
- usbd_desc: rename USBD_xxx descriptor opts to MICROPY_HW_USB_xxx
- usbd_cdc_interface: rename USBD_CDC_xx opts to MICROPY_HW_USB_xx
- powerctrl: support changing frequency on WB MCUs
- boards/NUCLEO_H743ZI2: add modified version of NUCLEO_H743ZI
- mbedtls: fix compile warning about uninitialized val
- enable MICROPY_PY_FSTRINGS by default
- add implementation of machine.bitstream
- Makefile: allow GIT_SUBMODULES and LIBS to be extended
- stm32_it: support TIM17 IRQs on WB MCUs
- disable computed goto on constrained boards
- storage: make extended-block-device more configurable
- boards/LEGO_HUB_NO6: change SPI flash storage to use hardware SPI
- boards/LEGO_HUB_NO6: skip first 1MiB of SPI flash for storage
- boards/LEGO_HUB_NO6: add make commands to backup/restore firmware
teensy port: no changes specific to this component/port
unix port:
- modffi: add option to lock GC in callback, and cfun access
- Makefile: add back LIB_SRC_C to list of object files
- variants: enable help and help("modules") on standard and dev
- Makefile: disable error compression on arm-linux-gnueabi-gcc
windows port:
- Makefile: add .exe extension to executables name
- appveyor: update to VS 2017 and use Python 3.8 for build/test
zephyr port:
- machine_spi: add support for hardware SPI
|
||
|
Damien George
|
136369d72f |
all: Update to point to files in new shared/ directory.
Signed-off-by: Damien George <damien@micropython.org> |
||
|
Damien George
|
4d546713ec |
shared: Introduce new top-level dir and move 1st party lib code there.
This commit moves all first-party code developed for this project from lib/
to shared/, so that lib/ now only contains third-party code.
The following directories are moved as-is from lib to shared:
lib/libc -> shared/libc
lib/memzip -> shared/memzip
lib/netutils -> shared/netutils
lib/timeutils -> shared/timeutils
lib/upytesthelper -> shared/upytesthelper
All files in lib/embed/ have been moved to shared/libc/.
lib/mp-readline has been moved to shared/readline.
lib/utils has been moved to shared/runtime, with the exception of
lib/utils/printf.c which has been moved to shared/libc/printf.c.
Signed-off-by: Damien George <damien@micropython.org>
|