Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The existing non-Docker instructions are basically impossible to follow
because the esp-open-sdk does not compile. Update these instructions to
use the exact toolchain that our CI uses.
Also split the Docker from non-Docker instructions, to avoid confusion
about which commands need to be prefixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It has been about 8 years since support for this chip was added. Reasons
to remove it are:
- It is no longer easy to obtain this part.
- There are now many other options for WiFi.
- It's not a good use of developer time to maintain it.
Signed-off-by: Damien George <damien@micropython.org>
Not safe to use mp_hal_delay_ms before boot if threading is enabled,
because threading will not have been initialised, and
MICROPY_EVENT_POLL_HOOK assumes threading is initialised.
HAL_Delay doesn't call MICROPY_EVENT_POLL_HOOK, but is still
power-efficient like mp_hal_delay_ms (unlike mp_hal_delay_us).
Fixes#7816.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than having the autobuild know about the particular variants, have
the mpconfigboard.mk describe them and make autobuild discover them
automatically.
Adds a "query-variants" target to stm32/Makefile to allow the set of
possible variants to be queried.
Removes pybv3 from the autobuild as this isn't use by the downloads page.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If mboot is built with support for packing (signing/encryption) it needs up
to 32KiB. So for simplicity increase the mboot region to 32KiB
unconditionally for WB55 boards (custom WB55 board configurations can still
provide their own linker scripts to override this).
It used to be 10 bit times, which is too short. The break state must be
longer than a regular character time, at least 13 bit times. This is now
implemented by reducing the baudrate while sending the "0". The break time
will now vary with data length and parity setting, but will at least be 15
bit times.
Tested with a GENERIC_SPIRAM, GENERIC_C3 and UM_TINYS2 board.
Set the channel with esp_wifi_set_channel(), which adds support for setting
the channel of the STA interface
Get the channel with esp_wifi_get_channel() which returns the actual wifi
channel of the radio, rather than the configured channel.
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.
This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).
The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled. So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether. That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).
Signed-off-by: Damien George <damien@micropython.org>
It seems sometimes gcc with LTO will generate otherwise valid assembly
listings that cause 'as' to error out when generating DWARF debug info; see
https://sourceware.org/bugzilla/show_bug.cgi?id=29494
Therefore, don't enable -g by default if LTO is on.
Enabling LTO=1 DEBUG=1 is still possible but may result in random errors
at link time due to 'as' (the error in this case is "Error: unaligned
opcodes detected in executable segment", and the only other easy workaround
is CFLAGS+=-fno-jump-tables which may increase code size significantly).
Follows on from fdfe4eca74
These were added in Python 3.5.
Enabled via MICROPY_PY_BUILTINS_BYTES_HEX, and enabled by default for all
ports that currently have ubinascii.
Rework ubinascii to use the implementation of these methods.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
PR #9012 (b2e8240268) changed the output to
$(BUILD)/$(PROG) but the tests are still looking for $(PROG).
Also remove the now-unnecessary override of $(PROG) in the standard
variant.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The separate A and RM toolchains have been discontinued and replaced
by a single toolchain. This updates the links to the RM toolchain to
the new toolchain.
Signed-off-by: David Lechner <david@pybricks.com>
Figure out path to arm-none-eabi-size the same way it's done for the
other binaries, instead of assuming it to be in the user's $PATH.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Create a new linker section .unitialized_bss for bss that does not need
zero-initialising.
Move gc_heap to this section, which saves ~30ms from rising edge of RESET
to setting a pin HIGH in MicroPython.
Zero fill happens in Pico SDK crt0.S before ROSC is configured. It's very,
very slow.
Signed-off-by: Phil Howard <phil@gadgetoid.com>
stty can provide the current terminal settings, so that they can be
stored in a shell variable and restored after running the firmware. This
avoids the complete "blanking" of the terminal, and thus also removes the
need for the sleep call.
The run target now references the firmware file using the BUILD variable
instead of using the hard coded "build/" path.
The executable now lives in the build directory, and since the build
directory already contains the variant name there is no need to also add
it to the executable.
Signed-off-by: Damien George <damien@micropython.org>
Binaries built using the Make build system now no longer appear in the
working directory of the build, but rather in the build directory. Thus
some paths had to be adjusted.
In-the-field use of these FUS/WS firmware update scripts has exposed some
weak points, causing corrupted FUS/WS firmware to be flashed to the unit.
The problems are mostly caused with the ST GUI application, but sometimes
from un-recognised failures during bin file transfer to the WB55 prior to
running the rfcore_firmware.py script. Other failures were caused by
incorrect load addresses being used, again both from user error copying the
address from the HTML release notes to the GUI tool, but also from
similarly not updating the address correctly in rfcore_firmware.py
To guard against these errors and make it easier to prepare different
versions, this commit adds a few features to the rfcore firmware update
tools:
- When creating the bin file, automatically parse the release note in the
folder to get the correct address.
- Add a footer to the bin file containing the name, version, CRC, address
etc.
- Before flashing rfcore, check if the same version is already installed.
- Verify the CRC and obfuscation key before flashing bin.
- Log the name and version of file being flashed.
The ntptime module was previously only included in the ESP8266 port. This
commit factors that module out into the extmod directory, makes it support
different epochs, and includes it in the rp2 port.
This adds support for the LEGO Hub No. 7, aka LEGO Technic Small hub, aka
LEGO SPIKE Essential hub. This board is largely similar to Hub No. 6:
- Same MCU (STM32F413 - different packaging with fewer pins).
- Same Bluetooth chip (TI CC2564).
- Same IMU chip.
- Similar external flash chip - 4MiB instead of 32MiB.
- 2 I/O ports instead of 6.
- No display - only status and battery LEDs.
- Different LED driver chip.
- Only 1 button which is also the power button.
- No speaker.
Signed-off-by: David Lechner <david@pybricks.com>
This adds configurable macros to define the timer and channel used to
provide the Bluetooth 32768 MHz clock. This will allow code to be shared
with LEGO_HUB_NO7.
Signed-off-by: David Lechner <david@pybricks.com>
This changes spiflash.py to read the flash chip ID at runtime to select the
read/write/erase commands. This will allow the code to be shared with
LEGO_HUB_NO7 which doesn't use the 32-bit commands.
Also remove an unused constant while we are touching this.
Signed-off-by: David Lechner <david@pybricks.com>
This changes appupdate.py to get the filesystem size at runtime. This will
allow the code to be shared with LEGO_HUB_NO7 which has a similar flash
chip with a different size.
Signed-off-by: David Lechner <david@pybricks.com>
This changes all uses of pins to use the alias names of the pins. This
makes the code easier to understand and will also allow sharing more code
with LEGO_HUB_NO7.
Signed-off-by: David Lechner <david@pybricks.com>
Also use mkrules.mk's submodule target rather than duplicating the call to
`submodule sync`.
Until we can find a way to use idf.py/cmake to discover submodules we have
no way to discover optional or board-specific submodules so need to err on
the side of including everything.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Used to be special-cased for Pico, but now everything depends on
micropython-lib if it's using a frozen manifest.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
