This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
Use this function instead of several individual configuration functions
to configure such things as Baud rate, transfer size, stop bits,
parity...
This function also resets both the RX and TX Hardware Fifo
reset functions are called to setup the hardware.
This lets the BLE stack run through the wait period after a VM run
when it may be waiting for more writes due to an auto-reload.
User BLE functionality will have their events stopped. Scanning and
advertising is also stopped.
The ``reset`` and ``read`` pins should be optional, but the espressif
code had several places where it assumed they are not, and a bug that
caused a crash on ``release_displays`` if they were made optional.
The bug was caused by the fields for storing pin numbers being set
to ``NO_PIN``, which has value of -1, while the fields have type
``uint8_t``. That set the actual value to 255, and a subsequent
comparison to ``NO_PIN`` returned false.
This allows board code to override the default pull up reset state.
It is useful for pins that are already externally connected, pulled
or otherwise used by the board.
Fixes#5931
This makes it easier to blanket never reset flash and USB pins. It
also allows us to set a custom state after reset. The first case
is for the double tap reset that needs to be pulled low.
Fixes#5893
This tweaks the RMT timing to better match the 1/3 and 2/3 of 800khz
guideline for timing. It also ensures a delay of 300 microseconds
with the line low before reset.
Pin reset is now changed to the IDF default which pulls the pin up
rather than CircuitPython's old behavior of floating the pin.
Fixes#5679
All 3 micros we care about (S2, S3, C3) state in the documentation
that DMA channel can be specified as SPI_DMA_CH_AUTO.
Specifying a specific DMA channel explicitly doesn't _ever_ work on
ESP32-S3, so no SPI bus could be used.
Testing performed: On the ESP32-S3-DevKitC, used neopixel_spi to
turn the onboard neopixel red, green, and blue
- update esp-idf to v4.4
- add esp32s3 support
- add analogio on esp32c3
- disable rgbmatrix on all espressif soc
Co-authored-by: Scott Shawcroft <scott@adafruit.com>
Co-authored-by: Seon Rozenblum <seon@unexpectedmaker.com>
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
By having a pair of buffers, the capture hardware can fill one buffer while
Python code (including displayio, etc) operates on the other buffer. This
increases the responsiveness of camera-using code.
On the Kaluga it makes the following improvements:
* 320x240 viewfinder at 30fps instead of 15fps using directio
* 240x240 animated gif capture at 10fps instead of 7.5fps
As discussed at length on Discord, the "usual end user" code will look like
this:
camera = ...
with camera.continuous_capture(buffer1, buffer2) as capture:
for frame in capture:
# Do something with frame
However, rather than presenting a context manager, the core code consists of
three new functions to start & stop continuous capture, and to get the next
frame. The reason is twofold. First, it's simply easier to implement the
context manager object in pure Python. Second, for more advanced usage, the
context manager may be too limiting, and it's easier to iterate on the right
design in Python code. In particular, I noticed that adapting the
JPEG-capturing programs to use continuous capture mode needed a change in
program structure.
The camera app was structured as
```python
while True:
if shutter button was just pressed:
capture a jpeg frame
else:
update the viewfinder
```
However, "capture a jpeg frame" needs to (A) switch the camera settings and (B)
capture into a different, larger buffer then (C) return to the earlier
settings. This can't be done during continuous capture mode. So just
restructuring it as follows isn't going to work:
```python
with camera.continuous_capture(buffer1, buffer2) as capture:
for frame in capture:
if shutter button was just pressed:
capture a jpeg frame, without disturbing continuous capture mode
else:
update the viewfinder
```
The continuous mode is only implemented in the espressif port; others
will throw an exception if the associated methods are invoked. It's not
impossible to implement there, just not a priority, since these micros don't
have enough RAM for two framebuffer copies at any resonable sizes.
The capture code, including single-shot capture, now take mp_obj_t in the
common-hal layer, instead of a buffer & length. This was done for the
continuous capture mode because it has to identify & return to the user the
proper Python object representing the original buffer. In the Espressif port,
it was convenient to implement single capture in terms of a multi-capture,
which is why I changed the singleshot routine's signature too.
