This reverts commit 6a3a742a6c.
The above commit has number of faults starting from the motivation down
to the actual implementation.
1. Faulty implementation.
The original code contained functions like:
NORETURN void nlr_jump(void *val) {
nlr_buf_t **top_ptr = &MP_STATE_THREAD(nlr_top);
nlr_buf_t *top = *top_ptr;
...
__asm volatile (
"mov %0, %%edx \n" // %edx points to nlr_buf
"mov 28(%%edx), %%esi \n" // load saved %esi
"mov 24(%%edx), %%edi \n" // load saved %edi
"mov 20(%%edx), %%ebx \n" // load saved %ebx
"mov 16(%%edx), %%esp \n" // load saved %esp
"mov 12(%%edx), %%ebp \n" // load saved %ebp
"mov 8(%%edx), %%eax \n" // load saved %eip
"mov %%eax, (%%esp) \n" // store saved %eip to stack
"xor %%eax, %%eax \n" // clear return register
"inc %%al \n" // increase to make 1, non-local return
"ret \n" // return
: // output operands
: "r"(top) // input operands
: // clobbered registers
);
}
Which clearly stated that C-level variable should be a parameter of the
assembly, whcih then moved it into correct register.
Whereas now it's:
NORETURN void nlr_jump_tail(nlr_buf_t *top) {
(void)top;
__asm volatile (
"mov 28(%edx), %esi \n" // load saved %esi
"mov 24(%edx), %edi \n" // load saved %edi
"mov 20(%edx), %ebx \n" // load saved %ebx
"mov 16(%edx), %esp \n" // load saved %esp
"mov 12(%edx), %ebp \n" // load saved %ebp
"mov 8(%edx), %eax \n" // load saved %eip
"mov %eax, (%esp) \n" // store saved %eip to stack
"xor %eax, %eax \n" // clear return register
"inc %al \n" // increase to make 1, non-local return
"ret \n" // return
);
for (;;); // needed to silence compiler warning
}
Which just tries to perform operations on a completely random register (edx
in this case). The outcome is the expected: saving the pure random luck of
the compiler putting the right value in the random register above, there's
a crash.
2. Non-critical assessment.
The original commit message says "There is a small overhead introduced
(typically 1 machine instruction)". That machine instruction is a call
if a compiler doesn't perform tail optimization (happens regularly), and
it's 1 instruction only with the broken code shown above, fixing it
requires adding more. With inefficiencies already presented in the NLR
code, the overhead becomes "considerable" (several times more than 1%),
not "small".
The commit message also says "This eliminates duplicated code.". An
obvious way to eliminate duplication would be to factor out common code
to macros, not introduce overhead and breakage like above.
3. Faulty motivation.
All this started with a report of warnings/errors happening for a niche
compiler. It could have been solved in one the direct ways: a) fixing it
just for affected compiler(s); b) rewriting it in proper assembly (like
it was before BTW); c) by not doing anything at all, MICROPY_NLR_SETJMP
exists exactly to address minor-impact cases like thar (where a) or b) are
not applicable). Instead, a backwards "solution" was put forward, leading
to all the issues above.
The best action thus appears to be revert and rework, not trying to work
around what went haywire in the first place.
These were copied from the stm32 port (then stmhal) at the very beginning
of this port, with the anticipation that the esp8266 port would have board
definition files with a list of valid pins and their names. But that has
not been implemented and likely won't be, so remove the corresponding lines
from the Makefile.
This patch adds in internal config value MICROPY_HW_ENABLE_HW_I2C that is
automatically configured, and enabled only if one or more hardware I2C
ports are defined in the mpconfigboard.h file. If none are defined then
the pyb.I2C class is excluded from the build, along with all supporting
code. The machine.I2C class will still be available for software I2C.
Disabling all hardware I2C on an F4 board saves around 10,000 bytes of code
and 200 bytes of RAM.
Each NLR implementation (Thumb, x86, x64, xtensa, setjmp) duplicates a lot
of the NLR code, specifically that dealing with pushing and popping the NLR
pointer to maintain the linked-list of NLR buffers. This patch factors all
of that code out of the specific implementations into generic functions in
nlr.c. This eliminates duplicated code.
The factoring also allows to make the machine-specific NLR code pure
assembler code, thus allowing nlrthumb.c to use naked function attributes
in the correct way (naked functions can only have basic inline assembler
code in them).
There is a small overhead introduced (typically 1 machine instruction)
because now the generic nlr_jump() must call nlr_jump_tail() rather than
them being one combined function.
set_equal is called only from set_binary_op, and this guarantees that the
second arg to set_equal is always a set or frozenset. So there is no need
to do a further check.
Previously, testing of stackless build happened (manually) in
travis-stackless branch. However, stackless offers important
featureset, so it's worth to test it as a part of the main
CI. Strict stackless is used because it's the "real" stackless
build, which avoids using C stack as much as possible (non-strict
just prefers heap over C stack, but may end up using the latter).
This implements .pend_throw(exc) method, which sets up an exception to be
triggered on the next call to generator's .__next__() or .send() method.
This is unlike .throw(), which immediately starts to execute the generator
to process the exception. This effectively adds Future-like capabilities
to generator protocol (exception will be raised in the future).
The need for such a method arised to implement uasyncio wait_for() function
efficiently (its behavior is clearly "Future" like, and normally would
require to introduce an expensive Future wrapper around all native
couroutines, like upstream asyncio does).
py/objgenerator: pend_throw: Return previous pended value.
This effectively allows to store an additional value (not necessary an
exception) in a coroutine while it's not being executed. uasyncio has
exactly this usecase: to mark a coro waiting in I/O queue (and thus
not executed in the normal scheduling queue), for the purpose of
implementing wait_for() function (cancellation of such waiting coro
by a timeout).
tinytest is written with the idea that tests won't write to stdout, so it
prints test name witjout newline, then executes test, then writes status.
But MicroPython tests write to stdout, so the test output becomes a mess.
So, instead print it like:
# starting basics/andor.py
... test output ...
basics/andor.py: OK
If TEST is defined, file it refers to will be used as the testsuite
source (should be generated with tools/tinytest-codegen.py).
"make-bin-testsuite" script is introduce to build such a binary.
The whole idea of --list-tests is that we prepare a list of tests to run
later, and currently don't have a connection to target board. Similarly
for --write-exp - only "python3" binary would be required for this operation,
not "micropython".
Some compilers can treat enum types as signed, in which case 3 bits is not
enough to encode all mp_raw_code_kind_t values. So change the type to
mp_uint_t.
