This changes appupdate.py to get the filesystem size at runtime. This will
allow the code to be shared with LEGO_HUB_NO7 which has a similar flash
chip with a different size.
Signed-off-by: David Lechner <david@pybricks.com>
This changes all uses of pins to use the alias names of the pins. This
makes the code easier to understand and will also allow sharing more code
with LEGO_HUB_NO7.
Signed-off-by: David Lechner <david@pybricks.com>
Prerequisite for enabling Link Time Optimisation.
The _bl_state address is the same as _estack, but _estack is referred to as
a uint32_t elsewhere in the code. LTO doesn't like it when the same symbol
has two different types.
Signed-off-by: Angus Gratton <gus@projectgus.com>
The following changes are made:
- Use software SPI for external SPI flash access when building mboot.
- Enable the mboot filesystem-loading feature, with FAT FS support.
- Increase the frequency of the CPU when in mboot to 96MHz, to increase the
speed of SPI flash accesses and programming.
Signed-off-by: Damien George <damien@micropython.org>
This allows a board to modify initial_r0 if needed.
Also make default board behaviour functions always available, named as
mboot_get_reset_mode_default and mboot_state_change_default.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds a board definition for NUCLEO_G0B1RE. This board has the
REPL on UART2 which is connected to the on-board ST-link USB-UART.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
These files that are reformatted only now fall under the list of files to
apply uncrustify/black formatting to.
Signed-off-by: Damien George <damien@micropython.org>
- Add board-level configuration option to set the SMPS supply mode.
- Wait for valid voltage levels after configuring the SMPS mode.
- Wait for external supply ready flag if SMPS supplies external circuitry.
This is enabled at MICROPY_CONFIG_ROM_LEVEL_EXTRA_FEATURES, which is the
default for stm32. Not setting the value in mpconfigboard.h allows boards
to optionally configure it.
Signed-off-by: Damien George <damien@micropython.org>
The default stm32lib remains lib/stm32lib, but it can now be easily
overriden at build time by specifying STM32LIB_DIR, or STM32LIB_CMSIS_DIR
and STM32LIB_HAL_DIR.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE. This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
The current ST HAL does not support reading the extended CSD so cannot
correctly detect the capacity of high-capacity cards. As a workaround, the
capacity can be forced via the MICROPY_HW_MMCARD_LOG_BLOCK_NBR config
option.
Signed-off-by: Damien George <damien@micropython.org>
These were commented correctly by their colour, but in the wrong order with
respect to the PCB silkscreen.
Fixes issue #8054.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of board pins, so that pins which have only the CPU specified in
pins.csv can still be used with mp_hal_pin_config_alt_static().
Signed-off-by: Damien George <damien@micropython.org>
This is to make the builds for all nucleo/discovery boards uniform, so they
can be treated the same by the auto build scripts.
The CI script is updated to explicitly enable mboot and packing, to test
these features.
Signed-off-by: Damien George <damien@micropython.org>
Quail (https://www.mikroe.com/quail, PID: MIKROE-1793) is based on an
STM32F427VI CPU, featuring 2048 kB of Flash memory and 192 kB of RAM. An
on-board Cypress S25FL164K adds 8 MB of SPI Flash.
Quail has 4 mikroBUS(TM) sockets for Mikroe click(TM) board connectivity,
along with 24 screw terminals for connecting additional electronics and two
USB ports (one for programming, the other for external mass storage).
4 UARTs, 2 SPIs and 1 I2C bus are available for communication.
Signed-off-by: Lorenzo Cappelletti <lorenzo.cappelletti@gmail.com>
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.
Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The H743 has equal sized pages of 128k, which means the filesystem doesn't
need to be near the beginning. This commit moves the filesystem to the
very end of flash, and extends it to 512k (4 pages).
Signed-off-by: Damien George <damien@micropython.org>
This change adds the OLIMEX H407 support to the STM32 port. The H407
(https://www.olimex.com/Products/ARM/ST/STM32-H407/) is simliar to the
already existing E407
(https://www.olimex.com/Products/ARM/ST/STM32-E407) but does not support
Ethernet and has a full-size USB-A port instead of a Mini-USB socket.
Both boards use the STM32F407ZGT6 CPU.
This port is basically a copy of the E407 but with changed pinmux:
* Removed Ethernet pin definition
* Removed UART1 (pins are used for other functions)
* Removed UART3 flow control pins (pins are used for other functions)
* Removed SD-Card detect pin (since it is not connected on the H407)
A REPL on UART3 is connected to the U3BOOT-header, a 3-pin header with RX,
TX and GND that is intended for the serial terminal.
Tested:
* Micro-SD Card is detected when inserted on RESET
* REPL on UART3 works
* Serial port on the mini USB socket
Signed-off-by: Chris Fiege <cfi@pengutronix.de>
This change allows a CPU pin to be hidden from the user by prefixing it
with a "-" in the pins.csv file for a board. It will still be available in
C code, just not exposed to Python.
Signed-off-by: Damien George <damien@micropython.org>
This commit is based upon prior work of @dpgeorge and @koendv.
MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)
Support has been added for the STM32H7B3I_DK board.
Signed-off-by: Jan Staal <info@janstaal.com>
This commit creates a new stm32 board for the NUCLEO_H743ZI2, which is the
current version of this from ST. This is a modified copy of the
NUCLEO_H743ZI board, and the ZI2 board differs in a few minor ways:
- LED2 has moved from PB7 to PE1 and is now yellow rather than blue
- the USB power enable has moved from PG6 to PG10
- the USER button is now pulled down
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
The ADC_FIRST_GPIO_CHANNEL and ADC_LAST_GPIO_CHANNEL macros are no longer
needed. Instead the pin_adcX table (X = 1, 2, 3) is now generated to be
the exact size needed for a given MCU, and MP_ARRAY_SIZE(pin_adcX) is used
to determine the upper bound.
This commit also allows CPU pins to be excluded from ADC configuration if
they are hidden by prefixing their name with a "-".
Signed-off-by: Damien George <damien@micropython.org>
With GCC 11 there is now a warning about array bounds of OTP-mac, due to
the OTP being a literal address.
Signed-off-by: Damien George <damien@micropython.org>
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.
Signed-off-by: Alexander Ziubin aziubin@googlemail.com
Support for C++ was added in 97960dc7de but
that commit didn't include the C++ exception handling table in the binary
firmware image. This commit fixes that.
Signed-off-by: Damien George <damien@micropython.org>
