Commit Graph

25 Commits

Author SHA1 Message Date
Paul Sokolovsky 97a0846af9 stmhal/diskio: Introduce MICROPY_HW_HAS_FLASH setting.
To allow to reuse stmhal/diskio for ports which don't have flash but have
other storage devices.
2016-02-06 15:07:01 +02:00
Damien George a8a4b01af6 stmhal: Add PWM capability for LED(3) and LED(4) on pyboards.
USB CDC no longer needs TIM3 (which was originally used for LED(4) PWM)
and so TIM3 has been freed for general purpose use by the user.  Hence
LED(4) lost its PWM capabilities.

This patch reinstates the PWM capabilities using a semi-generic piece
of code which allows to configure a timer and PWM channel to use for any
LED.  But the PWM capability is only configured if the LED is set to an
intensity between 1 and 254 (ie only when needed).  In that case the
relevant timer is configured for PWM.  It's up to the user to make sure
the timers are not used if PWM is active.

This patch also makes sure that PWM LEDs are turned off using standard
GPIO when calling led.off() or led.intensity(0), instead of just setting
the PWM counter to zero.
2016-01-29 22:44:43 +00:00
Damien George f7c4f9a640 stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx.
Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx
to 0 or 1.  Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI
and NSS.  This makes it the same as how I2C is configured.
2015-12-12 15:02:02 +00:00
T S 86aa16bea6 stmhal: Implement delayed RTC initialization with LSI fallback.
If RTC is already running at boot then it's left alone.  Otherwise, RTC is
started at boot but startup function returns straight away.  RTC startup
is then finished the first time it is used.  Fallback to LSI if LSE fails
to start in a certain time.

Also included:
 MICROPY_HW_CLK_LAST_FREQ
        hold pyb.freq() parameters in RTC backup reg
 MICROPY_HW_RTC_USE_US
        option to present datetime sub-seconds in microseconds
 MICROPY_HW_RTC_USE_CALOUT
        option to enable RTC calibration output

CLK_LAST_FREQ and RTC_USE_CALOUT are enabled for PYBv1.0.
2015-11-23 23:23:07 +00:00
Damien George 6f70283909 stmhal: Make accel AVDD pin configurable via mpconfigboard.h. 2015-10-29 22:40:42 +00:00
Damien George 70446f46c2 stmhal: Allow to name SPI busses, and give them names for pyboard. 2015-05-27 17:21:42 +01:00
Damien George 0e6f5e08e1 stmhal: Allow to name I2C busses, and give them names for pyboard. 2015-05-27 17:16:26 +01:00
Damien George 1775b65e07 stmhal: Remove PYBVxx defines and use config vars for UART/CAN names.
Now all stmhal-based boards can name their peripherals (if they want) to
any string.
2015-05-27 16:51:04 +01:00
Eero af Heurlin 2378be4e93 stmhal: Allow to configure UART pins completely via mpconfigboard.h. 2015-05-03 13:48:26 +01:00
Damien George d15fe5a6b3 stmhal: Make I2C busses and their pins configurable in mpconfigboard.h. 2015-04-18 21:40:59 +01:00
Damien George 2e5704d101 stmhal: Make a HW config option for LED4 being controlled by PWM. 2015-04-18 21:40:58 +01:00
Damien George 8bdbc20e74 stmhal: Make HSE PLL parameters configurable per board. 2015-04-18 21:40:58 +01:00
Damien George 49fe6dc89a stmhal: Add config option to use LSE/LSI for RTC.
Most boards (except the pyboard) don't have a 32kHz crystal so they
should use the LSI for the RTC.
2015-03-16 22:54:44 +00:00
Dave Hylands d7f199465f stmhal: Add support for FEZ Cerb40 II board from ghielectronics.com. 2015-01-21 00:11:04 +00:00
Damien George 131185a2b8 stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards.
This config option is for the USB OTG pin, pin A10.  This is used on
some boards but not others.  Eg PYBv3 uses PA10 for LED(2), so it
shouldn't be used for OTG ID (actually PA10 is multiplexed on this
board, but defaults to LED(2)).

Partially addresses issue #1059.
2015-01-12 16:13:29 +00:00
Damien George 181bfb6db2 stmhal: Add MICROPY_HW_USB_VBUS_DETECT_PIN option, for boards without it
Since all currently supported boards use pin A9 for this function, the
value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used,
just the fact that it is defined.

Addresses issue #1048.
2015-01-07 23:54:57 +00:00
Damien George 6dba992182 stmhal: Add config option to disable/enable CAN driver. 2014-10-05 18:05:26 +01:00
Damien George b766e79510 stmhal: Initial implementation of cc3k module and driver.
Pulled in and modified work done by mux/iabdalkader on cc3k driver, from
iabdalkader-cc3k-update branch.  That branch was terribly messy and had
too many conflicts to merge neatly.
2014-09-26 00:57:26 +01:00
Damien George 0c64c634ca stmhal: Add sys.platform string to PYBv1.0 (it's "pyboard"). 2014-08-10 17:49:52 +01:00
mux a75e382a9b Change MCU name config micro 2014-06-27 00:35:53 +02:00
mux fe81eea967 Add MICROPY_HW_MICRO_NAME to boards config 2014-06-19 14:40:57 +02:00
Damien George ae8feac598 stmhal: Wrap CC3000 driver in MICROPY_HW_ENABLE_CC3K.
This renames MICROPY_HW_HAS_WLAN to MICROPY_HW_ENABLE_CC3K (since it's a
driver, not a board feature) and wraps all CC3000 code in this #if.
It's disabled for all boards.
2014-05-03 17:32:55 +01:00
Damien George 4ae52d454c stmhal: Reinstate CC3000 driver from old stm/ port.
It's not enabled by default because it doesn't fully work.  It can
connect to an AP, get an IP address and do a host-lookup, but not yet do
send or recv on a socket.
2014-04-30 20:47:50 +01:00
Damien George ff91156d34 stmhal: Improved configurability for I2C and SPI busses.
The HAL handles for the I2C/SPI objects are rather large, so we don't
want to unnecessarily include them.
2014-04-20 19:06:15 +01:00
Damien George 09d207785c stmhal: Unify naming of HW config; make SD detect configurable.
All board config macros now begin with MICROPY_HW_.

Renamed PYBv10 to PYBV10, since macros should be all uppercase.

Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD
detect pin can be easily configured.
2014-03-30 12:30:35 +01:00