To enable parsing constants more efficiently, mp_parse should be allowed
to raise an exception, and mp_compile can already raise a MemoryError.
So these functions need to be protected by an nlr push/pop block.
This patch adds that feature in all places. This allows to simplify how
mp_parse and mp_compile are called: they now raise an exception if they
have an error and so explicit checking is not needed anymore.
There was a stray factor of 2 (VBAT_DIV) that looks like it was copied incorrectly from the read_core_vbat() function.
The factor exists in read_core_vbat() because VBAT is measured through a 2:1 voltage divider.
read_core_vref now returns values around 1.21V (assuming that external reference voltage is 3.3V) which is in line with the datasheet values.
See comment at http://forum.micropython.org/viewtopic.php?f=6&t=533&p=2991#p2991
This cleans up vstr so that it's a pure "variable buffer", and the user
can decide whether they need to add a terminating null byte. In most
places where vstr is used, the vstr did not need to be null terminated
and so this patch saves code size, a tiny bit of RAM, and makes vstr
usage more efficient. When null termination is needed it must be
done explicitly using vstr_null_terminate.
It uses RAM and on pyboard we are generally tight on RAM, so disable
this optimisation for general builds. If users need the speed then
they can build their own version. Maybe in the future we can have
different versions of pyboard firmware built with different tradeoffs.
accept might raise an exception, in which case the new socket is not
fully created. It has a finaliser so will run close() method when GC'd.
Before this patch close would try to close an invalid socket. Now
fixed.
setsockopt took address of stack value which became out of scope. Now
fixed.
With this patch str/bytes construction is streamlined. Always use a
vstr to build a str/bytes object. If the size is known beforehand then
use vstr_init_len to allocate only required memory. Otherwise use
vstr_init and the vstr will grow as needed. Then use
mp_obj_new_str_from_vstr to create a str/bytes object using the vstr
memory.
Saves code ROM: 68 bytes on stmhal, 108 bytes on bare-arm, and 336 bytes
on unix x64.
pyexec_friendly_repl_process_char() and friends, useful for ports which
integrate into existing cooperative multitasking system.
Unlike readline() refactor before, this was implemented in less formal,
trial&error process, minor functionality regressions are still known
(like soft&hard reset support). So, original loop-based pyexec_friendly_repl()
is left intact, specific implementation selectable by config setting.
This config option is for the USB OTG pin, pin A10. This is used on
some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it
shouldn't be used for OTG ID (actually PA10 is multiplexed on this
board, but defaults to LED(2)).
Partially addresses issue #1059.
Compiler optimises lookup of module.CONST when enabled (an existing
feature). Disabled by default; enabled for unix, windows, stmhal.
Costs about 100 bytes ROM on stmhal.
This allows to enable mem-info functions in micropython module, even if
MICROPY_MEM_STATS is not enabled. In this case, you get mem_info and
qstr_info but not mem_{total,current,peak}.
Since all currently supported boards use pin A9 for this function, the
value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used,
just the fact that it is defined.
Addresses issue #1048.
This is a simple optimisation inspired by JITing technology: we cache in
the bytecode (using 1 byte) the offset of the last successful lookup in
a map. This allows us next time round to check in that location in the
hash table (mp_map_t) for the desired entry, and if it's there use that
entry straight away. Otherwise fallback to a normal map lookup.
Works for LOAD_NAME, LOAD_GLOBAL, LOAD_ATTR and STORE_ATTR opcodes.
On a few tests it gives >90% cache hit and greatly improves speed of
code.
Disabled by default. Enabled for unix and stmhal ports.
This patch consolidates all global variables in py/ core into one place,
in a global structure. Root pointers are all located together to make
GC tracing easier and more efficient.
acoshf, asinhf, atanhf were added from musl. mathsincos.c was
split up into its original, separate files (from newlibe-nano-2).
tan was added.
All of the important missing float functions are now implemented,
and pyboard now passes tests/float/math_fun.py (finally!).
This patch adds a configuration option (MICROPY_CAN_OVERRIDE_BUILTINS)
which, when enabled, allows to override all names within the builtins
module. A builtins override dict is created the first time the user
assigns to a name in the builtins model, and then that dict is searched
first on subsequent lookups. Note that this implementation doesn't
allow deleting of names.
This patch also does some refactoring of builtins code, creating the
modbuiltins.c file.
Addresses issue #959.
The function is modeled after traceback.print_exception(), but unbloated,
and put into existing module to save overhead on adding another module.
Compliant traceback.print_exception() is intended to be implemented in
micropython-lib in terms of sys.print_exception().
This change required refactoring mp_obj_print_exception() to take pfenv_t
interface arguments.
Addresses #751.
Remove include of stm32f4xx_hal.h, replace by include of MICROPY_HAL_H
where needed, and make it compile without float support. This makes
these 3 modules much more generic and usable by other ports.
mp_obj_int_get_truncated is used as a "fast path" int accessor that
doesn't check for overflow and returns the int truncated to the machine
word size, ie mp_int_t.
Use mp_obj_int_get_truncated to fix struct.pack when packing maximum word
sized values.
Addresses issues #779 and #998.
mp_lexer_t type is exposed, mp_token_t type is removed, and simple lexer
functions (like checking current token kind) are now inlined.
This saves 784 bytes ROM on 32-bit unix, 348 bytes on stmhal, and 460
bytes on bare-arm. It also saves a tiny bit of RAM since mp_lexer_t
is a bit smaller. Also will run a bit more efficiently.
This patch overhauls the network driver interface. A generic NIC must
provide a set of C-level functions to implement low-level socket control
(eg socket, bind, connect, send, recv). Doing this, the network and
usocket modules can then use such a NIC to implement proper socket
control at the Python level.
This patch also updates the CC3K and WIZNET5K drivers to conform to the
new interface, and fixes some bugs in the drivers. They now work
reasonably well.
pyb.delay and pyb.udelay now use systick if IRQs are enabled, otherwise
they use a busy loop. Thus they work correctly when IRQs are disabled.
The busy loop is computed from the current CPU frequency, so works no
matter the CPU frequency.
The reason for having this delay is to reduce power consumption at the
REPL (HAL_Delay calls __WFI to idle the CPU). But stdin_rx_chr has a
__WFI in it anyway, so this delay call is not needed.
By removing this call, the readline input can consume characters much
more quickly (before was limited to 1000 chrs/s), and has much reduced
dependency on the specific port.
Also restrict higher frequencies to have a VCO_OUT frequency below
432MHz, as specified in the datasheet.
Docs improved to list allowed frequencies, and explain about USB
stability.
This is experimental support. API is subject to changes. RTS/CTS
available on UART(2) and UART(3) only. Use as:
uart = pyb.UART(2, 9600, flow=pyb.UART.RTS | pyb.UART.CTS)
This patch also enables non-blocking streams on stmhal port.
One can now make a USB-UART pass-through function:
def pass_through(usb, uart):
while True:
select.select([usb, uart], [], [])
if usb.any():
uart.write(usb.read(256))
if uart.any():
usb.write(uart.read(256))
pass_through(pyb.USB_VCP(), pyb.UART(1, 9600))
Improvements are:
2 ctrl-C's are now needed to truly kill running script on pyboard, so
make CDC interface allow multiple ctrl-C's through at once (ie sending
b'\x03\x03' to pyboard now counts as 2 ctrl-C's).
ctrl-C in friendly-repl can now stop multi-line input.
In raw-repl mode, use ctrl-D to indicate end of running script, and also
end of any error message. Thus, output of raw-repl is always at least 2
ctrl-D's and it's much easier to parse.
pyboard.py is now a bit faster, handles exceptions from pyboard better
(prints them and exits with exit code 1), prints out the pyboard output
while the script is running (instead of waiting till the end), and
allows to follow the output of a previous script when run with no
arguments.
This allows to implement KeyboardInterrupt on unix, and a much safer
ctrl-C in stmhal port. First ctrl-C is a soft one, with hope that VM
will notice it; second ctrl-C is a hard one that kills anything (for
both unix and stmhal).
One needs to check for a pending exception in the VM only for jump
opcodes. Others can't produce an infinite loop (infinite recursion is
caught by stack check).
TIM2_CH1_ETR is really bundling 2 functions to the same pin:
TIM2_CH1 (where its used as a channel)
TIM2_ETR (where iss used as an external trigger).
I fixed most of these a while back, but it looks like I missed this one.
Also make cc3k.send and cc3k.recv independent functions (not wrapped by
stream write/read). Also make wiznet5k.recv more memory efficient.
This might address issue #920.
UART object now uses a stream-like interface: read, readall, readline,
readinto, readchar, write, writechar.
Timeouts are configured when the UART object is initialised, using
timeout and timeout_char keyword args.
The object includes optional read buffering, using interrupts. You can set
the buffer size dynamically using read_buf_len keyword arg. A size of 0
disables buffering.
This makes open() and _io.FileIO() more CPython compliant.
The mode kwarg is fully iplemented.
The encoding kwarg is allowed but not implemented; mainly to allow
the tests to specify encoding for CPython, see #874
When loading the ELF binary to the board with a debugger, the debugger
needs to know at which point to start executing the code. Currently the
entry point defaults to the start of the .text section.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
This fixed an issue with a certain SD card sometimes not initialising
first time round. See issue #822 for related, and thanks to
@iabdalkader for the idea.
Also, usocket.readinto(). Known issue is that .readinto() should be available
only for binary files, but micropython uses single method table for both
binary and text files.
os, time, select modules are now prefixed with u, but are still
available (via weak links) as their original names.
ure and ujson now available as re and json via weak links.
This patch enables output on the complimentary channels (TIMx_CHyN).
For timers 1 and 8, deadtime can also be inserted when the channels
transition. For the pyboard, TIM8_CH1/CH1N and TIM8_CH2/CH2N can
take advantage of this.
Found these by compiling stmhal with mp_uint_t of type uint32_t instead
of unsigned int. This actually makes a difference to the code, but just
a curiosity.
Timers now have the following new features:
- can init freq using floating point; eg tim.init(freq=0.1)
- tim.source_freq() added to get freq of timer clock source
- tim.freq() added to get/set freq
- print(tim) now prints freq
Eg pyb.freq(120000000) sets the CPU to 120MHz. The frequency can be set
at any point in the code, and can be changed as many times as you like.
Note that any active timers will need to be reconfigured after a freq
change.
Valid range is 24MHz to 168MHz (but not all freqs are supported). The
code maintains a 48MHz clock for the USB at all times and it's possible
to change the frequency at a USB REPL and keep the REPL alive (well,
most of the time it stays, sometimes it resets the USB for some reason).
Note that USB does not work with pyb.freq of 24MHz.
Remove reference to pyb.gc; add reference to pyb.millis.
There are lots of functions not listed when you run help(), but it would
be too much to list them all, so we list only some basic, useful ones.
Addresses issue #846.
As per issue #876, the network module is used to configure NICs
(hardware modules) and configure routing. The usocket module is
supposed to implement the normal Python socket module and selects the
underlying NIC using routing logic.
Right now the routing logic is brain dead: first-initialised,
first-used. And the routing table is just a list of registered NICs.
cc3k and wiznet5k work, but not at the same time due to C name clashes
(to be fixed).
Note that the usocket module has alias socket, so that one can import
socket and it works as normal. But you can also override socket with
your own module, using usocket at the backend.
In CPython IOError (and EnvironmentError) is deprecated and aliased to
OSError. All modules that used to raise IOError now raise OSError (or a
derived exception).
In Micro Python we never used IOError (except 1 place, incorrectly) and
so don't need to keep it.
See http://legacy.python.org/dev/peps/pep-3151/ for background.
Teensy doesn't need to worry about overflows since all of
its timers are only 16-bit.
For PWM, the pulse width needs to be able to vary from 0..period+1
(pulse-width == period+1 corresponds to 100% PWM)
I couldn't test the 0xffffffff cases since we can't currently get a
period that big in python. With a prescaler of 0, that corresponds
to a freq of 0.039 (i.e. cycle every 25.56 seconds), and we can't
set that using freq or period.
I also tested both stmhal and teensy with floats disabled, which
required a few other code changes to compile.
Pulled in and modified work done by mux/iabdalkader on cc3k driver, from
iabdalkader-cc3k-update branch. That branch was terribly messy and had
too many conflicts to merge neatly.
Fix stmhal and teensy print routines to report actual prescaler an period.
Fix teensy build to use soft-float
Add USE_ARDUINO_TOOLCHAIN option to teensy build
mp_parse_node_free now frees the memory associated with non-interned
strings. And the parser calls mp_parse_node_free when discarding a
non-used node (such as a doc string).
Also, the compiler now frees the parse tree explicitly just before it
exits (as opposed to relying on the caller to do this).
Addresses issue #708 as best we can.
Stack is full descending and must be 8-byte aligned. It must start off
pointing to just above the last byte of RAM.
Previously, stack started pointed to last byte of RAM (eg 0x2001ffff)
and so was not 8-byte aligned. This caused a bug in combination with
alloca.
This patch also updates some debug printing code.
Addresses issue #872 (among many other undiscovered issues).
This allows to set the pulse width (for PWM mode) as a ratio relative to
the period of the timer. Eg, 0.5 is a 50% duty cycle. You can set the
ratio in the channel init, or using channel.pulse_width_ratio; the
latter can also read the pulse width as a ratio.
