testing performed:
* successfully store and retrieve a 500kB file on the flash
* square wave output on each pin appears on o'scope
* board.SPI(), board.SERIAL(), board.I2C() all construct
Introduces a way to place CircuitPython code and data into
tightly coupled memory (TCM) which is accessible by the CPU in a
single cycle. It also frees up room in the corresponding cache for
intermittent data. Loading from external flash is slow!
The data cache is also now enabled.
Adds support for the iMX RT 1021 chip. Adds three new boards:
* iMX RT 1020 EVK
* iMX RT 1060 EVK
* Teensy 4.0
Related to #2492, #2472 and #2477. Fixes#2475.
It's extremely dubious that we have these handles that we think
are to GC'd memory at a time when the gc pool may not be initialized.
Hopefully, they WERE valid GC memory and are undisturbed by the teardown
of the interpreter that can lead to this state.
In this case, don't try to m_free them, the memory will become free when
the GC heap is reinitialized.
Closes: #2338 (together with previous commit)
By treating each unicode code-point as a single entity for huffman
compression, the overall compression rate can be somewhat improved
without changing the algorithm. On the decompression side, when
compressed values above 127 are encountered, they need to be
converted from a 16-bit Unicode code point into a UTF-8 byte
sequence.
Doing this returns approximately 1.5kB of flash storage with the
zh_Latn_pinyin translation. (292 -> 1768 bytes remaining in my build
of trinket_m0)
Other "more ASCII" translations benefit less, and in fact
zh_Latn_pinyin is no longer the most constrained translation!
(de_DE 1156 -> 1384 bytes free in flash, I didn't check others
before pushing for CI)
English is slightly pessimized, 2840 -> 2788 bytes, probably mostly
because the "values" array was changed from uint8_t to uint16_t,
which is strictly not required for an all-ASCII translation. This
could probably be avoided in this case, but as English is not the
most constrained translation it doesn't really matter.
Testing performed: built for feather nRF52840 express and trinket m0
in English and zh_Latn_pinyin; ran and verified the localized
messages such as
Àn xià rènhé jiàn jìnrù REPL. Shǐyòng CTRL-D chóngxīn jiāzài.
and
Press any key to enter the REPL. Use CTRL-D to reload.
were properly displayed.
This improves performance of running python code by 34%, based
on the "pystone" benchmark on metro m4 express at 5000 passes
(1127.65 -> 1521.6 passes/second).
In addition, by instrumenting the tick function and monitoring on an
oscilloscope, the time actually spent in run_background_tasks() on
the metro m4 decreases from average 43% to 0.5%. (however, there's
some additional overhead that is moved around and not accounted for
in that "0.5%" figure, each time supervisor_run_background_tasks_if_tick
is called but no tick has occurred)
On the CPB, it increases pystone from 633 to 769, a smaller percentage
increase of 21%. I did not measure the time actually spent in
run_background_tasks() on CPB.
Testing performed: on metro m4 and cpb, run pystone adapted from python3.4
(change time.time to time.monotonic for sub-second resolution)
Besides running a 5000 pass test, I also ran a 50-pass test while
scoping how long an output pin was set. Average: 34.59ms or 1445/s on m4,
67.61ms or 739/s on cbp, both matching the other pystone result reasonably
well.
import pystone
import board
import digitalio
import time
d = digitalio.DigitalInOut(board.D13)
d.direction = digitalio.Direction.OUTPUT
while True:
d.value = 0
time.sleep(.01)
d.value = 1
pystone.main(50)
This code is shared by most parts, except where not all the #ifdefs
inside the tick function were present in all ports. This mostly would
have broken gamepad tick support on non-samd ports.
The "ms32" and "ms64" variants of the tick functions are introduced
because there is no 64-bit atomic read. Disabling interrupts avoids
a low probability bug where milliseconds could be off by ~49.5 days
once every ~49.5 days (2^32 ms).
Avoiding disabling interrupts when only the low 32 bits are needed is a minor
optimization.
Testing performed: on metro m4 express, USB still works and
time.monotonic_ns() still counts up
In cases where more than one board is connected to a single computer it can become pretty hard to figure out which board you're actually talking to. For example, if you have several MIDI-compatible boards they all show up as "CircuitPython MIDI". This change allows boards to replace the "CircuitPython" part of their USB descriptors with more specific text, for example, "CircuitPython Feather" or just "Feather". This will let folks more easily tell boards apart.
The new option is named `USB_INTERFACE_NAME` and is available in `mkconfigboard.mk`. For example:
```
USB_INTERFACE_NAME = "Feather"
```
This PR refines the _bleio API. It was originally motivated by
the addition of a new CircuitPython service that enables reading
and modifying files on the device. Moving the BLE lifecycle outside
of the VM motivated a number of changes to remove heap allocations
in some APIs.
It also motivated unifying connection initiation to the Adapter class
rather than the Central and Peripheral classes which have been removed.
Adapter now handles the GAP portion of BLE including advertising, which
has moved but is largely unchanged, and scanning, which has been enhanced
to return an iterator of filtered results.
Once a connection is created (either by us (aka Central) or a remote
device (aka Peripheral)) it is represented by a new Connection class.
This class knows the current connection state and can discover and
instantiate remote Services along with their Characteristics and
Descriptors.
Relates to #586
The GitHub Actions build for this PR is failing for reasons that make no sense. Make a tiny commit change to see if it will refresh things and work again.
