Commit Graph

11 Commits

Author SHA1 Message Date
Mike Causer 47b778332a all: Replace busses with buses.
"buses" is the widely accepted plural form of "bus".
2021-05-20 23:22:03 +10:00
roland van straten 26a78edb49 stm32/boards/NUCLEO_F767ZI: Update pins, peripherals and total flash.
- Removed remarks on DFU/OCD in mpconfigboard.h because deploy-stlink works
  fine too.
- Added more UARTs, I2C, corrected SPI, CAN, etc; verified against CubeMX.
- Adapted pins.csv to remove errors, add omissions, etc. according to
  NUCLEO-144 User Manual.
- Changed linker file stm32f767.ld to reflect correct size of the Flash.
- Tested with LAN and SD card.
2019-12-19 11:43:19 +11:00
roland van straten 8af139e8a4 stm32/boards/NUCLEO_F767ZI: Add pins and config for using an SD card.
The Nucleo board does not have an SD card slot but does have the requisite
pins next to each other and labelled, so provide the configuration for
convenience.
2019-12-19 11:28:47 +11:00
Damien George e61862d063 stm32/boards: Update to use new build config for lwip component. 2019-03-04 23:34:03 +11:00
Damien George 8daec24168 stm32/boards/NUCLEO_F767ZI: Enable lwIP and Ethernet peripheral. 2019-02-26 23:32:19 +11:00
Damien George 75a35448e1 stm32/boards/NUCLEO_F767ZI: Fix up comments about HCLK computation. 2019-02-26 22:44:27 +11:00
rolandvs 958fa74521 stm32/boards: Ensure USB OTG power is off for NUCLEO_F767ZI.
And update the GPIO init for NUCLEO_H743ZI to consistently use the mphal
functions.
2018-05-30 09:51:19 +10:00
Damien George a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George 34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George 02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00
Damien George 01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00