Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself. This patch switches to use those
names in most places so it is easier to update the HAL in the future.
Prior to this patch the USBD driver did not handle the recipient correctly
for setup requests. It was not interpreting the req->wIndex field in the
right way: in some cases this field indicates the endpoint number but the
code was assuming it always indicated the interface number.
This patch fixes this. The only noticeable change is to the MSC
interface, which should now correctly respond to the USB_REQ_CLEAR_FEATURE
request and hence unmount properly from the host when requested.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
This file mirrors py/mpconfig.h but for board-level config options. It
provides a default configuration, to be overridden by a specific
mpconfigboard.h file, as well as setting up certain macros to automatically
configure a board.
The calls to rtc_init_start(), sdcard_init() and storage_init() are all
guarded by a check for first_soft_reset, so it's simpler to just put them
all before the soft-reset loop, without the check.
The call to machine_init() can also go before the soft-reset loop because
it is only needed to check the reset cause which can happen once at the
first boot. To allow this to work, the reset cause must be set to SOFT
upon a soft-reset, which is the role of the new function machine_deinit().
Upon boot the RTC early-init function should detect if LSE or LSI is
already selected/running and, if so, use it. When the LSI has previously
(in the previous reset cycle) been selected as the clock source the only
way to reliably tell is if the RTCSEL bits of the RCC_BDCR are set to the
correct LSI value. In particular the RCC_CSR bits for LSI control do not
indicate if the LSI is ready even if it is selected.
This patch removes the check on the RCC_CSR bits for the LSI being on and
ready and only uses the check on the RCC_BDCR to see if the LSI should be
used straightaway. This was tested on a PYBLITEv1.0 and with the patch the
LSI persists correctly as the RTC source as long as the backup domain
remains powered.
Previously, if LSE is selected but fails and the RTC falls back to LSI,
then the rtc_info flags would incorrectly state that LSE is used. This
patch fixes that by setting the bit in rtc_info only after the clock is
ready.
There is an underlying hardware SPI driver (built on top of the STM HAL)
and then on top of this sits the legacy pyb.SPI class as well as the
machine.SPI class. This patch improves the separation between these
layers, in particular decoupling machine.SPI from pyb.SPI.
The SPI sub-system is independent from the uPy state (eg the heap) and so
can safely persist across a soft reset. And this is actually necessary for
drivers that rely on SPI and that also need to persist across soft reset
(eg external SPI flash memory).
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode. To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY. High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.
This patch has been tested on an STM32F733.
By defining MICROPY_HW_USB_MAIN_DEV a given board can select to use either
USB_PHY_FS_ID or USB_PHY_HS_ID as the main USBD peripheral, on which the
REPL will appear. If not defined this will be automatically configured.
There's no need to have these as separate functions, they just take up
unnecessary code space and combining them allows to factor common code, and
also allows to support arbitrary string descriptor indices.
The routine waits for the DMA to finish, which is signalled from a DMA IRQ
handler. Using WFI makes the CPU sleep while waiting for the IRQ to arrive
which decreases power consumption. To make it work correctly the check for
the change in state must be atomic and so IRQs must be disabled during the
check. The key feature of the Cortex MCU that makes this possible is that
WFI will exit when an IRQ arrives even if IRQs are disabled.
Build and test 32bit and 64bit versions of the windows port using gcc
from mingw-w64. Note a bunch of tests which rely on floating point
math/printing have been disabled for now since they fail.
The number of registers used should be 10, not 12, to match the assembly
code in nlrx64.c. With this change the 64bit mingw builds don't need to
use the setjmp implementation, and this fixes miscellaneous crashes and
assertion failures as reported in #1751 for instance.
To avoid mistakes in the future where something gcc-related for Windows
only gets fixed for one particular compiler/environment combination,
make use of a MICROPY_NLR_OS_WINDOWS macro.
To make sure everything nlr-related is now ok when built with gcc this
has been verified with:
- unix port built with gcc on Cygwin (i686-pc-cygwin-gcc and
x86_64-pc-cygwin-gcc, version 6.4.0)
- windows port built with mingw-w64's gcc from Cygwin
(i686-w64-mingw32-gcc and x86_64-w64-mingw32-gcc, version 6.4.0)
and MSYS2 (like the ones on Cygwin but version 7.2.0)
Add some features which are already enabled in the unix port and
default to using the Python stack for scoped allocations: this can be
more performant in cases the heap is heavily used because for example
the memory needed for storing *args and **kwargs doesn't require
scanning the heap to find a free block.
For MSVC off_t is defined in sys/types.h but according to the comment
earlier in mpconfigport.h this cannot be included directly.
So just make off_t the same as mp_off_t.
This fixes the build for MSVC with MICROPY_STREAMS_POSIX_API
enabled because stream.h uses off_t.
These were copied from the stm32 port (then stmhal) at the very beginning
of this port, with the anticipation that the esp8266 port would have board
definition files with a list of valid pins and their names. But that has
not been implemented and likely won't be, so remove the corresponding lines
from the Makefile.
