With using UART FIFO, the timeout should be long enough that FIFO becomes
empty. Since previous data transfer may be ongoing, the timeout must be
timeout_char multiplied by FIFO size + 1.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
Since commit 3533924c36 the zlib module has
been replaced by the new deflate module. This commit updates the script
fwupdate.py to use the new deflate module.
Signed-off-by: Oliver Joos <oliver.joos@hispeed.ch>
The primary purpose of this commit is to make decompress default to
wbits=15 when the format is gzip (or auto format with gzip detected). The
idea is that someone decompressing a gzip stream should be able to use the
default `deflate.DeflateIO(f)` and it will "just work" for any input
stream, even though it uses a lot of memory.
This is done by making uzlib report gzip files as having wbits set to 15
in their header (where it previously only set the wbits out parameter for
zlib files), and then fixing up the logic in `deflateio_init_read`.
Updates the documentation to match.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Down to 50 baud (in reverence to Jean-Maurice-Émile Baudot). Implemented
for the MIMXRT10xx MCU's only. The MIMXRT1176 runs down to 300 baud.
Signed-off-by: robert-hh <robert@hammelrath.com>
The code did not check at deinit whether a UART was initialized. That did
not matter for all MCU's except MIMXRT1176, which crashes at the second
soft reset in a row.
But since it is a general problem to use UART methods of a UART which has
been deinitialized, checks were added to all applicable methods for a clear
response instead of e.g. a crash.
Deinitialize UART using software reset. It resets the UART but keeps it
accessible for software, avoiding an exception when UART registers are
accessed after a DeInit.
Signed-off-by: robert-hh <robert@hammelrath.com>
Following other ports, IRQ priorities and related functions are moved to
their own header, to simplify mpconfigport.h.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This commit allows other ports to reuse the CYW43 HCI driver, by replacing
all Bluetooth UART and control named pins with defines in config files and
using `mpbthci` abstract functions (i.e. `mp_bluetooth_hci_*`) instead of
the STM32 specific UART functions.
Note: the function `cywbt_wait_cts_low` does not need to switch the CTS
pin from alternate function to GPIO to read it. At least on stm32, mimxrt
it's possible to just read the pin input. For example, see the STM32F7
RM0410 section 6.3.11, and the `SION` for IMXRT. So this function can
also be available for other ports if the pin mode switching is removed.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This commit adds the necessary configuration and hooks to get the CYW43
driver working with the mimxrt port.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is a basic SDIO driver for the mimxrt port, that was added mainly to
support the CYW43 WiFi driver, and as such it only supports the commands
required by the CYW43 driver (but more commands can be added easily). The
driver performs non-blocking DMA transfers, and can detect and recover from
errors.
Note: because the mimxrt port is missing static alternate functions, named
pins and other pin related functions, currently the alternate functions for
USDHC 1 and 2 are hard-coded in the driver.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Add portable pin config macros to mphalport.h. And add a function to
configure pins with more pin options such as alt function, pull, speed,
drive, interrupt mode, etc.
Note: this new `machine_pin_config()` function can replace
`machine_pin_set_mode()`, but the latter is left as-is to avoid breaking
anything.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is not working/tested. The display requires an initialization sequence,
and its SPI bus is on the other side of an I2C GPIO expander making things
more difficult.
Otherwise if/when the finaliser runs for this newly created SSLSocket the
mbedtls state will be freed again.
Signed-off-by: Damien George <damien@micropython.org>
The rp2 port was enabling SSL and had finalizers enabled via the "extra
features" level, but missed explicitly enabling `MICROPY_PY_SSL_FINALISER`
(like esp32, stm32, and mimxrt did).
This commit makes `MICROPY_PY_SSL_FINALISER` default to enabled if
finalizers are enabled, and removes the explicit setting of this for
esp32, stm32, mimxrt (because they all use the "extra features" level).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The only reason that const had to be disabled was to make the test output
match CPython when const was involved. Instead, this commit fixes the test
to handle the lines where const is used.
Also:
- remove the special handling for MICROPY_PERSISTENT_CODE_SAVE in
unix/mpconfigport.h, and make this automatic.
- move the check for MICROPY_PERSISTENT_CODE_SAVE to where it's used (like
we do for other similar checks) and add a comment explaining it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This test was failing on CPython 3.11 as it now emits `0` as the line
number for the "call" event corresponding to import, where as in 3.6 it had
`1` as the line number.
We maintain the old behavior, but in order to make this test pass on both
CPython versions, the trace handler now converts the `0` to a `1`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Yuuki NAGAO
Bob Abeles
Oliver Joos
Jim Mussared
Jeff Epler
Melissa LeBlanc-Williams
robert-hh
iabdalkader
Tirtharaj Sinha
Scott Shawcroft
Damien George
Hosted Weblate
hexthat
Jonny Bergdahl
Wellington Terumi Uemura
Bill Sideris
Bobby Jap