These ports don't need anything from extmod so don't include those files
at all in the build. This speeds up the build by about 10% when building
with a single core.
Currently only the first 2 args are used, but this patch should at least
make getaddrinfo() signature-compatible with CPython and other bare-metal
ports that use the lwip bindings.
Prior to this patch, storage.c was a combination of code that handled
either internal flash or external SPI flash and exposed one of them as a
block device for the local storage. It was also exposed to the USB MSC.
This patch splits out the flash and SPI code to separate files, which each
provide a general block-device interface (at the C level). Then storage.c
just picks one of them to use as the local storage medium. The aim of this
factoring is to allow to add new block devices in the future and allow for
easier configurability.
This patch allows to completely compile-out support for USB, and no-USB is
now the default. If a board wants to enable USB it should define:
#define MICROPY_HW_ENABLE_USB (1)
And then one or more of the following to select the USB PHY:
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_HS (1)
#define MICROPY_HW_USB_HS_IN_FS (1)
Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself. This patch switches to use those
names in most places so it is easier to update the HAL in the future.
Prior to this patch the USBD driver did not handle the recipient correctly
for setup requests. It was not interpreting the req->wIndex field in the
right way: in some cases this field indicates the endpoint number but the
code was assuming it always indicated the interface number.
This patch fixes this. The only noticeable change is to the MSC
interface, which should now correctly respond to the USB_REQ_CLEAR_FEATURE
request and hence unmount properly from the host when requested.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
This file mirrors py/mpconfig.h but for board-level config options. It
provides a default configuration, to be overridden by a specific
mpconfigboard.h file, as well as setting up certain macros to automatically
configure a board.
The calls to rtc_init_start(), sdcard_init() and storage_init() are all
guarded by a check for first_soft_reset, so it's simpler to just put them
all before the soft-reset loop, without the check.
The call to machine_init() can also go before the soft-reset loop because
it is only needed to check the reset cause which can happen once at the
first boot. To allow this to work, the reset cause must be set to SOFT
upon a soft-reset, which is the role of the new function machine_deinit().
Upon boot the RTC early-init function should detect if LSE or LSI is
already selected/running and, if so, use it. When the LSI has previously
(in the previous reset cycle) been selected as the clock source the only
way to reliably tell is if the RTCSEL bits of the RCC_BDCR are set to the
correct LSI value. In particular the RCC_CSR bits for LSI control do not
indicate if the LSI is ready even if it is selected.
This patch removes the check on the RCC_CSR bits for the LSI being on and
ready and only uses the check on the RCC_BDCR to see if the LSI should be
used straightaway. This was tested on a PYBLITEv1.0 and with the patch the
LSI persists correctly as the RTC source as long as the backup domain
remains powered.
Previously, if LSE is selected but fails and the RTC falls back to LSI,
then the rtc_info flags would incorrectly state that LSE is used. This
patch fixes that by setting the bit in rtc_info only after the clock is
ready.
There is an underlying hardware SPI driver (built on top of the STM HAL)
and then on top of this sits the legacy pyb.SPI class as well as the
machine.SPI class. This patch improves the separation between these
layers, in particular decoupling machine.SPI from pyb.SPI.
The SPI sub-system is independent from the uPy state (eg the heap) and so
can safely persist across a soft reset. And this is actually necessary for
drivers that rely on SPI and that also need to persist across soft reset
(eg external SPI flash memory).
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode. To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY. High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.
This patch has been tested on an STM32F733.
By defining MICROPY_HW_USB_MAIN_DEV a given board can select to use either
USB_PHY_FS_ID or USB_PHY_HS_ID as the main USBD peripheral, on which the
REPL will appear. If not defined this will be automatically configured.
