For the 3 ports that already make use of this feature (stm32, nrf and
teensy) this doesn't make any difference, it just allows to disable it from
now on.
For other ports that use pyexec, this decreases code size because the debug
printing code is dead (it can't be enabled) but the compiler can't deduce
that, so code is still emitted.
Most stm32 boards can now be built in nan-boxing mode via:
$ make NANBOX=1
Note that if float is enabled then it will be forced to double-precision.
Also, native emitters will be disabled.
Move webrepl support code from ports/esp8266/modules into extmod/webrepl
(to be alongside extmod/modwebrepl.c), and use frozen manifests to include
it in the build on esp8266 and esp32.
A small modification is made to webrepl.py to make it work on non-ESP
ports, i.e. don't call dupterm_notify if not available.
- Corrected pin assignments and checked with CubeMX.
- Added additional I2C and UARTs.
- Added Ethernet interface definitions with lwIP and SSL support (but
Ethernet is currently unsupported on H7 MCUs so not fully enabled).
- Removed remarks on DFU/OCD in mpconfigboard.h because deploy-stlink works
fine too.
- Added more UARTs, I2C, corrected SPI, CAN, etc; verified against CubeMX.
- Adapted pins.csv to remove errors, add omissions, etc. according to
NUCLEO-144 User Manual.
- Changed linker file stm32f767.ld to reflect correct size of the Flash.
- Tested with LAN and SD card.
The Nucleo board does not have an SD card slot but does have the requisite
pins next to each other and labelled, so provide the configuration for
convenience.
Implements text, rodata and bss generalised relocations, as well as generic
qstr-object linking. This allows importing dynamic native modules on all
supported architectures in a unified way.
The default protection for the BLE ringbuf is to use
MICROPY_BEGIN_ATOMIC_SECTION, which disables all interrupts. On stm32 it
only needs to disable the lowest priority IRQ, pendsv, because that's the
IRQ level at which the BLE stack is driven.
qstrs in this file are always included in all builds, even if not used
anywhere. So remove those that are never needed, and make USB names
conditional on having USB enabled.
And return -MP_EIO if calling storage_read_block/storage_write_block fails.
This lines up with the return type and value (negative for error) of the
calls to MICROPY_HW_BDEV_READBLOCKS (and WRITEBLOCKS, and BDEV2 versions).
The pyb.Flash() class can now be used to construct objects which reference
sections of the flash storage, starting at a certain offset and going for a
certain length. Such objects also support the extended block protocol.
The signature for the constructor is: pyb.Flash(start=-1, len=-1).
This commit refactors and generalises the boot-mount routine on stm32 so
that it can mount filesystems of arbitrary type. That is, it no longer
assumes that the filesystem is FAT. It does this by using mp_vfs_mount()
which does auto-detection of the filesystem type.
Using mp_hal_delay_ms allows the scheduler to run, which might result in
another transmit operation happening, which would bypass the sleep (and
fail). Use mp_hal_delay_us instead.
The compile-time configuration value MICROPY_HW_RTC_USER_MEM_MAX can now be
used to define the amount of memory set aside for RTC.memory(). If this
value is configured to zero then the RTC.memory functionality is not
included in the build.
The IDF heap is more fragmented with IDF 4 and mbedtls cannot allocate
enough RAM with 16+16kiB for both in and out buffers, so reduce output
buffer size.
Fixes issue #5303.
This commit removes the Makefile-level MICROPY_FATFS config and moves the
MICROPY_VFS_FAT config to the Makefile level to replace it. It also moves
the include of the oofatfs source files in the build from each port to a
central place in extmod/extmod.mk.
For a port to enabled VFS FAT support it should now set MICROPY_VFS_FAT=1
at the level of the Makefile. This will include the relevant oofatfs files
in the build and set MICROPY_VFS_FAT=1 at the C (preprocessor) level.
This commit adds support for littlefs (v2) on all esp32 boards.
The original FAT filesystem still works and any board with a preexisting
FAT filesystem will still work as normal. It's possible to switch to
littlefs by reformatting the block device using:
import uos, flashbdev
uos.VfsLfs2.mkfs(flashbdev.bdev)
Then when the board reboots (soft or hard) the new littlefs filesystem will
be mounted. It's possible to switch back to a FAT filesystem by formatting
with uos.VfsFat.mkfs(flashbdev.bdev).
