The ring buffer previously used a single unsigned byte field to save the
length, meaning that it would overflow for large characteristic value
responses.
With this commit it now use a 16-bit length instead and has code to
explicitly truncate at UINT16_MAX (although this should be impossible to
achieve in practice).
This commit makes sure that all discovery complete and read/write status
events set the status to zero on success.
The status value will be implementation-dependent on non-success cases.
On btstack there's no status associated with the read result, it comes
through as a separate event. This allows you to detect read failures or
timeouts.
There doesn't appear to be any use for only triggering on specific events,
so it's just easier to number them sequentially. This makes them smaller
values so they take up only 1 byte in the ringbuf, only 1 byte for the
opcode in the bytecode, and makes room for more events.
Also add a couple of new event types that need to be implemented (to avoid
re-numbering later).
And rename _COMPLETE and _STATUS to _DONE for consistency.
In the future the "trigger" keyword argument can be reinstated by requiring
the user to compute the bitmask, eg:
ble.irq(handler, 1 << _IRQ_SCAN_RESULT | 1 << _IRQ_SCAN_DONE)
Before this change, any NimBLE error that does not appear in the
ble_hs_err_to_errno_table maps to return code 0, meaning success. If we
miss adding an error code to the table we end up returning success in case
of failure.
Instead, handle the zero case explicitly and default to MP_EIO. This
allows removing the now-redundant MP_EIO entries from the mapping.
This commit allows the user to set/get the GAP device name used by service
0x1800, characteristic 0x2a00. The usage is:
BLE.config(gap_name="myname")
print(BLE.config("gap_name"))
As part of this change the compile-time setting
MICROPY_PY_BLUETOOTH_DEFAULT_NAME is renamed to
MICROPY_PY_BLUETOOTH_DEFAULT_GAP_NAME to emphasise its link to GAP and this
new "gap_name" config value. And the default value of this for the NimBLE
bindings is changed from "PYBD" to "MPY NIMBLE" to be more generic.
Ujson should only worry about whitespace before JSON. This becomes apparent when you are using MP stream protocol to read directly from input buffers.
When you attempt to read(1) on a UART (and possibly other protocols) you have to wait for either the byte or the timeout.
Fixes:
- Waiting for a timeout after you have completed reading a correct and complete JSON off the input.
- Raising an OSError after reading a correct and complete JSON off the input.
- Eating more data than semantically owned off the input buffer.
- Blocking to start parsing JSON until the entire JSON body has been loaded into a potentially large, contiguous Python object.
Code you would write before:
```
line = board_busio_uart_port.read_line()
json_dict = json.loads(line)
```
or reaching for fixed buffers and swapping them around in Python.
Code that did not work before that does now:
```
json_dict = json.load(board_busio_uart_port)
```
- This removes the need for intermediate copies of data when reading JSON from micropython stream protocol inputs.
- It also increases total application speed by parsing JSON concurrently with receiving on boards that read from UART via DMA.
- It simplifies code that users write while improving their apps.
If the new name start with '/', cur_dir is not prepened any more, so that
the current working directory is respected. And extend the test cases for
rename to cover this functionality.
This change scans for '.', '..' and multiple '/' and normalizes the new
path name. If the resulting path does not exist, an error is raised.
Non-existing interim path elements are ignored if they are removed during
normalization.
This fixes the bug, that stat(filename) would not consider the current
working directory. So if e.g. the cwd is "lib", then stat("main.py") would
return the info for "/main.py" instead of "/lib/main.py".
For ports that have a system malloc which is not garbage collected (eg
unix, esp32), the stream object for the DB must be retained separately to
prevent it from being reclaimed by the MicroPython GC (because the
berkeley-db library uses malloc to allocate the DB structure which stores
the only reference to the stream).
Although in some cases the user code will explicitly retain a reference to
the underlying stream because it needs to call close() on it, this is not
always the case, eg in cases where the DB is intended to live forever.
Fixes issue #5940.
But only when bluetooth is enabled, i.e. if building the dev or coverage
variants, and we have libusb available.
Update travis to match, i.e. specify the variant when doing
`make submodules`.
This commit adds full support to the unix port for Bluetooth using the
common extmod/modbluetooth Python bindings. This uses the libusb HCI
transport, which supports many common USB BT adaptors.
This change is made for two reasons:
1. A 3rd-party library (eg berkeley-db-1.xx, axtls) may use the system
provided errno for certain errors, and yet MicroPython stream objects
that it calls will be using the internal mp_stream_errno. So if the
library returns an error it is not known whether the corresponding errno
code is stored in the system errno or mp_stream_errno. Using the system
errno in all cases (eg in the mp_stream_posix_XXX wrappers) fixes this
ambiguity.
2. For systems that have threading the system-provided errno should always
be used because the errno value is thread-local.
For systems that do not have an errno, the new lib/embed/__errno.c file is
provided.
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
Initially some of these were found building the unix coverage variant on
MacOS because that build uses clang and has -Wdouble-promotion enabled, and
clang performs more vigorous promotion checks than gcc. Additionally the
codebase has been compiled with clang and msvc (the latter with warning
level 3), and with MICROPY_FLOAT_IMPL_FLOAT to find the rest of the
conversions.
Fixes are implemented either as explicit casts, or by using the correct
type, or by using one of the utility functions to handle floating point
casting; these have been moved from nativeglue.c to the public API.
Now that error string compression is supported it's more important to have
consistent error string formatting (eg all lowercase English words,
consistent contractions). This commit cleans up some of the strings to
make them more consistent.
This commit adds Loop.new_event_loop() which is used to reset the singleton
event loop. This functionality is put here instead of in Loop.close() to
make it possible to write code that is compatible with CPython.
The latest version of BTstack has a bug fixed so that it correctly
configures scan parameters if they are set right after activating the
stack. This means that BLE.gap_scan() will correctly set the scanning to
passive and so SCAN_RSP events are not passed through, so we don't need to
explicitly filter them in our bindings.
This commit makes all functions and function wrappers in modubinascii.c
STATIC and conditional on the MICROPY_PY_UBINASCII setting, which will
exclude the file from qstr/ compressed-string searching when ubinascii is
not enabled. The now-unused modubinascii.h header file is also removed.
The cc3200 port is updated accordingly to use this module in its entirety
instead of providing its own top-level definition of ubinascii.
This was originally like this because the cc3200 port has its own ubinascii
module which referenced these methods. The plan appeared to be that the
API might diverge (e.g. hardware crc), but this should be done similar to
I2C/SPI via a port-specific handler, rather than the port having its own
definition of the module. Having a centralised module definition also
enforces consistency of the API among ports.
This commit adds support for global exception handling in uasyncio
according to the CPython error handling:
https://docs.python.org/3/library/asyncio-eventloop.html#error-handling-api
This allows a program to receive exceptions from detached tasks and log
them to an appropriate location, instead of them being printed to the REPL.
The implementation preallocates a context dictionary so in case of an
exception there shouldn't be any RAM allocation.
The approach here is compatible with CPython except that in CPython the
exception handler is called once the task that threw an uncaught exception
is freed, whereas in MicroPython the exception handler is called
immediately when the exception is thrown.
These were found by buiding the unix coverage variant on macOS (so clang
compiler). Mostly, these are fixing implicit cast of float/double to
mp_float_t which is one of those two and one mp_int_t to size_t fix for
good measure.
https://www.python.org/dev/peps/pep-0475/
This implements something similar to PEP 475 on the unix port, and for the
VfsPosix class.
There are a few differences from the CPython implementation:
- Since we call mp_handle_pending() between any ENITR's, additional
functions could be called if MICROPY_ENABLE_SCHEDULER is enabled, not
just signal handlers.
- CPython only handles signal on the main thread, so other threads will
raise InterruptedError instead of retrying. On MicroPython,
mp_handle_pending() will currently raise exceptions on any thread.
A new macro MP_HAL_RETRY_SYSCALL is introduced to reduce duplicated code
and ensure that all instances behave the same. This will also allow other
ports that use POSIX-like system calls (and use, eg, VfsPosix) to provide
their own implementation if needed.
Implements Task and TaskQueue classes in C, using a pairing-heap data
structure. Using this reduces RAM use of each Task, and improves overall
performance of the uasyncio scheduler.
This commit adds a completely new implementation of the uasyncio module.
The aim of this version (compared to the original one in micropython-lib)
is to be more compatible with CPython's asyncio module, so that one can
more easily write code that runs under both MicroPython and CPython (and
reuse CPython asyncio libraries, follow CPython asyncio tutorials, etc).
Async code is not easy to write and any knowledge users already have from
CPython asyncio should transfer to uasyncio without effort, and vice versa.
The implementation here attempts to provide good compatibility with
CPython's asyncio while still being "micro" enough to run where MicroPython
runs. This follows the general philosophy of MicroPython itself, to make it
feel like Python.
The main change is to use a Task object for each coroutine. This allows
more flexibility to queue tasks in various places, eg the main run loop,
tasks waiting on events, locks or other tasks. It no longer requires
pre-allocating a fixed queue size for the main run loop.
A pairing heap is used to queue Tasks.
It's currently implemented in pure Python, separated into components with
lazy importing for optional components. In the future parts of this
implementation can be moved to C to improve speed and reduce memory usage.
But the aim is to maintain a pure-Python version as a reference version.
Also support MP_STREAM_GET_FILENO ioctl. The stdio flush change was done
previously for the unix port in 3e0b46b9af.
These changes make this POSIX file implementation equivalent to the unix
file implementation.
Fixes UDP non-blocking recv so it returns EAGAIN instead of ETIMEDOUT.
Timeout waiting for incoming data is also improved by replacing 100ms delay
with poll_sockets(), as is done in other parts of this module.
Fixes issue #5759.
This commit changes the BLE _IRQ_SCAN_RESULT data from:
addr_type, addr, connectable, rssi, adv_data
to:
addr_type, addr, adv_type, rssi, adv_data
This allows _IRQ_SCAN_RESULT to handle all scan result types (not just
connectable and non-connectable passive scans), and to distinguish between
them using adv_type which is an integer taking values 0x00-0x04 per the BT
specification.
This is a breaking change to the API, albeit a very minor one: the existing
connectable value was a boolean and True now becomes 0x00, False becomes
0x02.
Documentation is updated and a test added.
Fixes#5738.
This commit ensures that the BLE stack is active before allowing operations
that may otherwise crash if it's not active. It also clarifies the state
better (adding the "stopping" state) and renames mp_bluetooth_is_enabled to
the more self-explanatory mp_bluetooth_is_active.
This makes a cleaner separation between the: driver, HCI UART and BT stack.
Also updated the naming to be more consistent (mp_bluetooth_hci_*).
Work done in collaboration with Jim Mussared aka @jimmo.
Move extmod/modbluetooth_nimble.* to extmod/nimble. And move common
Makefile lines to extmod/nimble/nimble.mk (which was previously only used
by stm32). This allows (upcoming) btstack to follow a similar structure.
Work done in collaboration with Jim Mussared aka @jimmo.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX. It also reduces code size by a
small amount on some ports.
Most types are in rodata/ROM, and mp_obj_base_t.type is a constant pointer,
so enforce this const-ness throughout the code base. If a type ever needs
to be modified (eg a user type) then a simple cast can be used.
The struct member "dest" should never be less than "destStart", so their
difference is never negative. Cast as such to make the comparison
explicitly unsigned, ensuring the compiler produces the correct comparison
instruction, and avoiding any compiler warnings.
Move webrepl support code from ports/esp8266/modules into extmod/webrepl
(to be alongside extmod/modwebrepl.c), and use frozen manifests to include
it in the build on esp8266 and esp32.
A small modification is made to webrepl.py to make it work on non-ESP
ports, i.e. don't call dupterm_notify if not available.
The size of the event ringbuf was previously fixed to compile-time config
value, but it's necessary to sometimes increase this for applications that
have large characteristic buffers to read, or many events at once.
With this commit the size can be set via BLE.config(rxbuf=512), for
example. This also resizes the internal event data buffer which sets the
maximum size of incoming data passed to the event handler.
Protocols are nice, but there is no way for C code to verify whether
a type's "protocol" structure actually implements some particular
protocol. As a result, you can pass an object that implements the
"vfs" protocol to one that expects the "stream" protocol, and the
opposite of awesomeness ensues.
This patch adds an OPTIONAL (but enabled by default) protocol identifier
as the first member of any protocol structure. This identifier is
simply a unique QSTR chosen by the protocol designer and used by each
protocol implementer. When checking for protocol support, instead of
just checking whether the object's type has a non-NULL protocol field,
use `mp_proto_get` which implements the protocol check when possible.
The existing protocols are now named:
protocol_framebuf
protocol_i2c
protocol_pin
protocol_stream
protocol_spi
protocol_vfs
(most of these are unused in CP and are just inherited from MP; vfs and
stream are definitely used though)
I did not find any crashing examples, but here's one to give a flavor of what
is improved, using `micropython_coverage`. Before the change,
the vfs "ioctl" protocol is invoked, and the result is not intelligible
as json (but it could have resulted in a hard fault, potentially):
>>> import uos, ujson
>>> u = uos.VfsPosix('/tmp')
>>> ujson.load(u)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ValueError: syntax error in JSON
After the change, the vfs object is correctly detected as not supporting
the stream protocol:
>>> ujson.load(p)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: stream operation not supported
This allows the user to explicitly select the behaviour of the write to the
remote peripheral. This is needed for peripherals that have
characteristics with WRITE_NO_RESPONSE set (instead of normal WRITE). The
function's signature is now:
BLE.gattc_write(conn_handle, value_handle, data, mode=0)
mode=0 means write without response, while mode=1 means write with
response. The latter was the original behaviour so this commit is a change
in behaviour of this method, and one should specify 1 as the 4th argument
to get back the old behaviour.
In the future there could be more modes supported, such as long writes.
The default protection for the BLE ringbuf is to use
MICROPY_BEGIN_ATOMIC_SECTION, which disables all interrupts. On stm32 it
only needs to disable the lowest priority IRQ, pendsv, because that's the
IRQ level at which the BLE stack is driven.
This removes the limit on data coming in from a BLE.gattc_read() request,
or a notify with payload (coming in to a central). In both cases the data
coming in to the BLE callback is now limited only by the available data in
the ringbuf, whereas before it was capped at (default hard coded) 20 bytes.
Instead of enqueue_irq() inspecting the ringbuf to decide whether to
schedule the IRQ callback (if ringbuf is empty), maintain a flag that knows
if the callback is on the schedule queue or not. This saves about 150
bytes of code (for stm32 builds), and simplifies all uses of enqueue_irq()
and schedule_ringbuf().
The address, adv payload and uuid fields of the event are pre-allocated by
modbluetooth, and reused in the IRQ handler. Simplify this and move all
storage into the `mp_obj_bluetooth_ble_t` instance.
This now allows users to hold on to a reference to these instances without
crashes, although they may be overwritten by future events. If they want
to hold onto the values longer term they need to copy them.
Remove existing scan result events from the ringbuf if the ringbuf is full
and we're trying to enqueue any other event. This is needed so that events
such as SCAN_COMPLETE are always put on the ringbuf.
This commit removes the Makefile-level MICROPY_FATFS config and moves the
MICROPY_VFS_FAT config to the Makefile level to replace it. It also moves
the include of the oofatfs source files in the build from each port to a
central place in extmod/extmod.mk.
For a port to enabled VFS FAT support it should now set MICROPY_VFS_FAT=1
at the level of the Makefile. This will include the relevant oofatfs files
in the build and set MICROPY_VFS_FAT=1 at the C (preprocessor) level.
POSIX poll should always return POLLERR and POLLHUP in revents, regardless
of whether they were requested in the input events flags.
See issues #4290 and #5172.
POSIX poll should always return POLLERR and POLLHUP in revents, regardless
of whether they were requested in the input events flags.
See issues #4290 and #5172.
- Adds an explicit way to set the size of a value's internal buffer,
replacing `ble.gatts_write(handle, bytes(size))` (although that
still works).
- Add an "append" mode for values, which means that remote writes
will append to the buffer.
This commit adds helper functions to call readblocks/writeblocks with a
fourth argument, the byte offset within a block.
Although the mp_vfs_blockdev_t struct has grown here by 2 machine words, in
all current uses of this struct within this repository it still fits within
the same number of GC blocks.
For consistency with "umachine". Now that weak links are enabled
by default for built-in modules, this should be a no-op, but allows
extension of the bluetooth module by user code.
Also move registration of ubluetooth to objmodule rather than
port-specific.
NimBLE doesn't actually copy this data, it requires it to stay live.
Only dereference when we register a new set of services.
Fixes#5226
This will allow incrementally adding services in the future, so
rename `reset` to `append` to make it clearer.
Internally change the representation of UUIDs to LE uint8* to simplify this.
This allows UUIDs to be easily used in BLE payloads (such as advertising).
Ref: #5186
This avoids a confusing ENOMEM raised from gap_advertise if there is
currently an active connection. This refers to the static connection
buffer pre-allocated by Nimble (nothing to do with MicroPython heap
memory).
This is to more accurately match the BLE spec, where intervals are
configured in units of channel hop time (625us). When it was
specified in ms, not all "valid" intervals were able to be
specified.
Now that we're also allowing configuration of scan interval, this
commit updates advertising to match.
This adds two additional optional kwargs to `gap_scan()`:
- `interval_us`: How long between scans.
- `window_us`: How long to scan for during a scan.
The default with NimBLE is a 11.25ms window with a 1.28s interval.
Changing these parameters is important for detecting low-frequency
advertisements (e.g. beacons).
Note: these params are in microseconds, not milliseconds in order
to allow the 625us granularity offered by the spec.
On other ports (e.g. ESP32) they provide a complete Nimble implementation
(i.e. we don't need to use the code in extmod/nimble). This change
extracts out the bits that we don't need to use in other ports:
- malloc/free/realloc for Nimble memory.
- pendsv poll handler
- depowering the cywbt
Also cleans up the root pointer management.
With this patch alignment is done relative to the start of the buffer that
is being unpacked, not the raw pointer value, as per CPython.
Fixes issue #3314.
As per the README.md of the upstream source at
https://github.com/B-Con/crypto-algorithms, this source code was released
into the public domain, so make that explicit in the copyright line in the
header.
Enabled via MICROPY_PY_URE_DEBUG, disabled by default (but enabled on unix
coverage build). This is a rarely used feature that costs a lot of code
(500-800 bytes flash). Debugging of regular expressions can be done
offline with other tools.
The helper function exec_user_callback executes within the context of an
lwIP C callback, and the user (Python) callback to be scheduled may want to
perform further TCP/IP actions, so the latter should be scheduled to run
outside the lwIP context (otherwise it's effectively a "hard IRQ" and such
callbacks have lots of restrictions).
If tcp_write returns ERR_MEM then it's not a fatal error but instead means
the caller should retry the write later on (and this is what lwIP's netconn
API does).
This fixes problems where a TCP send would raise OSError(ENOMEM) in
situations where the TCP/IP stack is under heavy load. See eg issues #1897
and #1971.
Setting MICROPY_PY_USSL and MICROPY_SSL_MBEDTLS at the Makefile-level will
now build mbedTLS from source and include it in the build, with the ussl
module using this TLS library. Extra settings like MBEDTLS_CONFIG_FILE may
need to be provided by a given port.
If a port wants to use its own mbedTLS library then it should not set
MICROPY_SSL_MBEDTLS at the Makefile-level but rather set it at the C level,
and provide the library as part of the build in its own way (see eg esp32
port).
In d5f0c87bb9 this call to tcp_poll() was
added to put a timeout on closing TCP sockets. But after calling
tcp_close() the PCB may be freed and therefore invalid, so tcp_poll() can
not be used at that point. As a fix this commit calls tcp_poll() before
closing the TCP PCB. If the PCB is subsequently closed and freed by
tcp_close() or tcp_abort() then the PCB will not be on any active list and
the callback will not be executed, which is the desired behaviour (the
_lwip_tcp_close_poll() callback only needs to be called if the PCB remains
active for longer than the timeout).
Commit 2848a613ac introduced a bug where
lwip_socket_free_incoming() accessed pcb.tcp->state after the PCB was
closed. The state may have changed due to that close call, or the PCB may
be freed and therefore invalid. This commit fixes that by calling
lwip_socket_free_incoming() before the PCB is closed.
For example: i2c.writevto(addr, (buf1, buf2)). This allows to efficiently
(wrt memory) write data composed of separate buffers, such as a command
followed by a large amount of data.
It consists of:
1. "do_handhake" param (default True) to wrap_socket(). If it's False,
handshake won't be performed by wrap_socket(), as it would be done in
blocking way normally. Instead, SSL socket can be set to non-blocking mode,
and handshake would be performed before the first read/write request (by
just returning EAGAIN to these requests, while instead reading/writing/
processing handshake over the connection). Unfortunately, axTLS doesn't
really support non-blocking handshake correctly. So, while framework for
this is implemented on MicroPython's module side, in case of axTLS, it
won't work reliably.
2. Implementation of .setblocking() method. It must be called on SSL socket
for blocking vs non-blocking operation to be handled correctly (for
example, it's not enough to wrap non-blocking socket with wrap_socket()
call - resulting SSL socket won't be itself non-blocking). Note that
.setblocking() propagates call to the underlying socket object, as
expected.
For this, add wrap_socket(do_handshake=False) param. CPython doesn't have
such a param at a module's global function, and at SSLContext.wrap_socket()
it has do_handshake_on_connect param, but that uselessly long.
Beyond that, make write() handle not just MBEDTLS_ERR_SSL_WANT_WRITE, but
also MBEDTLS_ERR_SSL_WANT_READ, as during handshake, write call may be
actually preempted by need to read next handshake message from peer.
Likewise, for read(). And even after the initial negotiation, situations
like that may happen e.g. with renegotiation. Both
MBEDTLS_ERR_SSL_WANT_READ and MBEDTLS_ERR_SSL_WANT_WRITE are however mapped
to the same None return code. The idea is that if the same read()/write()
method is called repeatedly, the progress will be made step by step anyway.
The caveat is if user wants to add the underlying socket to uselect.poll().
To be reliable, in this case, the socket should be polled for both POLL_IN
and POLL_OUT, as we don't know the actual expected direction. But that's
actually problematic. Consider for example that write() ends with
MBEDTLS_ERR_SSL_WANT_READ, but gets converted to None. We put the
underlying socket on pull using POLL_IN|POLL_OUT but that probably returns
immediately with POLL_OUT, as underlyings socket is writable. We call the
same ussl write() again, which again results in MBEDTLS_ERR_SSL_WANT_READ,
etc. We thus go into busy-loop.
So, the handling in this patch is temporary and needs fixing. But exact way
to fix it is not clear. One way is to provide explicit function for
handshake (CPython has do_handshake()), and let *that* return distinct
codes like WANT_READ/WANT_WRITE. But as mentioned above, past the initial
handshake, such situation may happen again with at least renegotiation. So
apparently, the only robust solution is to return "out of bound" special
sentinels like WANT_READ/WANT_WRITE from read()/write() directly. CPython
throws exceptions for these, but those are expensive to adopt that way for
efficiency-conscious implementation like MicroPython.
In CPython the random module is seeded differently on each import, and so
this new macro option MICROPY_PY_URANDOM_SEED_INIT_FUNC allows to implement
such a behaviour.
Since commit da938a83b5 the tcp_arg() that is
set for the new connection is the new connection itself, and the parent
listening socket is found in the pcb->connected entry.
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
Some users of this module may require the LwIP stack to run at an elevated
priority, to protect against concurrency issues with processing done by the
underlying network interface. Since LwIP doesn't provide such protection
it must be done here (the other option is to run LwIP in a separate thread,
and use thread protection mechanisms, but that is a more heavyweight
solution).
The bug polling for readability was: if alloc==0 and tcp.item==NULL then
the code would incorrectly check tcp.array[iget] which is an invalid
dereference when alloc==0. This patch refactors the code to use a helper
function lwip_socket_incoming_array() to return the correct pointer for the
incomming connection array.
Fixes issue #4511.
This feature is controlled at compile time by MICROPY_PY_URE_SUB, disabled
by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
This feature is controlled at compile time by
MICROPY_PY_URE_MATCH_SPAN_START_END, disabled by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
This feature is controlled at compile time by MICROPY_PY_URE_MATCH_GROUPS,
disabled by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
As mentioned in #4450, `websocket` was experimental with a single intended
user, `webrepl`. Therefore, we'll make this change without a weak
link `websocket` -> `uwebsocket`.
Previously crypto-algorithms impl was included even if MICROPY_SSL_MBEDTLS
was in effect, thus we relied on the compiler/linker to cut out the unused
functions.
Python defines warnings as belonging to categories, where category is a
warning type (descending from exception type). This is useful, as e.g.
allows to disable warnings selectively and provide user-defined warning
types. So, implement this in MicroPython, except that categories are
represented just with strings. However, enough hooks are left to implement
categories differently per-port (e.g. as types), without need to patch each
and every usage.
This header is deprecated as of mbedtls 2.8.0, as shipped with Ubuntu
18.04. Leads to #warning which is promoted to error with uPy compile
options.
Note that the current version of mbedtls is 2.14 at the time of writing.
It's more robust to have the version defined statically in a header file,
rather than dynamically generating it via git using a git tag. In case
git doesn't exist, or a different source control tool is used, it's
important to still have the uPy version number available.
SHORT, INT, LONG, LONGLONG, and unsigned (U*) variants are being defined.
This is done at compile using GCC-style predefined macros like
__SIZEOF_INT__. If the compiler doesn't have such defines, no such types
will be defined.
The recent implementation of the listen backlog meant that the logic to
test for readability of such a socket changed, and this commit updates the
logic to work again.
Array to hold waiting connections is in-place if backlog=1, else is a
dynamically allocated array. Incoming connections are processed FIFO
style to maintain fairness.
sizeof() can work in two ways: a) calculate size of already instantiated
structure ("sizeof variable") - in this case we already no layout; b) size
of structure decsription ("sizeof type"). In the latter case, LAYOUT_NATIVE
was assumed, but there should possibility to calculate size for other
layouts too. So, with this patch, there're now 2 forms:
uctypes.sizeof(struct)
uctypes.sizeof(struct_desc, layout)
This value is unused. It was an artifact of early draft design, but
bitfields were optimized to use scalar one-word encoding, to allow
compact encoding of typical multiple bitfields in MCU control
registers.
Since mbedtls 2.7.0 new digest functions were introduced with a "_ret"
suffix to allow the functions to return an error message (eg, if the
underlying hardware acceleration failed). These new functions must be used
instead of the old ones to prevent deprecation warnings, or link errors for
missing functions, depending on the mbedtls configuration.
This removes the need for a separate axtls build stage, and builds all
axtls object files along with other code. This simplifies and cleans up
the build process, automatically builds axtls when needed, and puts the
axtls object files in the correct $(BUILD) location.
The MicroPython axtls configuration file is provided in
extmod/axtls-include/config.h
Commit 95e70cd0ea 'time: Use 1970 epoch' changed epoch for the time
module, but not for other users. This patch does the same for the only
other core timeutils user: extmod/vfs_fat.c:fat_vfs_stat().
Other timeutils users: cc3200, esp8266 and stm32, are not changed.
Ports that don't use long ints, will still get wrong time values from
os.stat().
This saves code space in builds which use link-time optimization.
The optimization drops the untranslated strings and replaces them
with a compressed_string_t struct. It can then be decompressed to
a c string.
Builds without LTO work as well but include both untranslated
strings and compressed strings.
This work could be expanded to include QSTRs and loaded strings if
a compress method is added to C. Its tracked in #531.
The underlying socket can handling polling, and any other transparent ioctl
requests. Note that CPython handles the case of polling an ssl object by
polling the file descriptor of the underlying socket file, and that
behaviour is emulated here.
Otherwise they may be called on a socket that no longer exists.
For example, if the GC calls the finaliser on the socket and then reuses
its heap memory, the "callback" entry of the old socket may contain invalid
data. If lwIP then calls the TCP callback the code may try to call the
user callback object which is now invalid. The lwIP callbacks must be
deregistered during the closing of the socket, before all the pcb pointers
are set to NULL.
This feature is controlled at compile time by MICROPY_PY_URE_SUB, disabled
by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
This feature is controlled at compile time by
MICROPY_PY_URE_MATCH_SPAN_START_END, disabled by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
This feature is controlled at compile time by MICROPY_PY_URE_MATCH_GROUPS,
disabled by default.
Thanks to @dmazzella for the original patch for this feature; see #3770.
This will allow implementations other than axTLS.
This commit includes additions of checks and clarifications of exceptions
related to user input.
To make the interface cleaner, I've disallowed switching from encrypt to
decrypt in the same object, as this is not always possible with other
crypto libraries (not all libraries have AES_convert_key like axTLS).
Allow including crypto consts based on compilation settings. Disabled by
default to reduce code size; if one wants extra code readability, can
enable them.
The API follows guidelines of https://www.python.org/dev/peps/pep-0272/,
but is optimized for code size, with the idea that full PEP 0272
compatibility can be added with a simple Python wrapper mode.
The naming of the module follows (u)hashlib pattern.
At the bare minimum, this module is expected to provide:
* AES128, ECB (i.e. "null") mode, encrypt only
Implementation in this commit is based on axTLS routines, and implements
following:
* AES 128 and 256
* ECB and CBC modes
* encrypt and decrypt
With this patch objects are only checked that they have the stream protocol
at the start of their use as a stream, and afterwards the efficient
mp_get_stream() helper is used to extract the stream protocol C methods.
This patch changes dupterm to call the native C stream methods on the
connected stream objects, instead of calling the Python readinto/write
methods. This is much more efficient for native stream objects like UART
and webrepl and doesn't require allocating a special dupterm array.
This change is a minor breaking change from the user's perspective because
dupterm no longer accepts pure user stream objects to duplicate on. But
with the recent addition of uio.IOBase it is possible to still create such
classes just by inheriting from uio.IOBase, for example:
import uio, uos
class MyStream(uio.IOBase):
def write(self, buf):
# existing write implementation
def readinto(self, buf):
# existing readinto implementation
uos.dupterm(MyStream())
Via the config value MICROPY_PY_UHASHLIB_SHA256. Default to enabled to
keep backwards compatibility.
Also add default value for the sha1 class, to at least document its
existence.
For consistency with other modules, and to help avoid clashes with the
actual underlying functions that do the hashing (eg
crypto-algorithms/sha256.c:sha256_update).
Following other C-level protocols, this VFS protocol is added to help
abstract away implementation details of the underlying VFS in an efficient
way. As a starting point, the import_stat function is put into this
protocol so that the VFS sub-system does not need to know about every VFS
implementation in order to do an efficient stat for importing files.
In the future it might be worth adding other functions to this protocol.
This VFS component allows to mount a host POSIX filesystem within the uPy
VFS sub-system. All traditional POSIX file access then goes through the
VFS, allowing to sandbox a uPy process to a certain sub-dir of the host
system, as well as mount other filesystem types alongside the host
filesystem.
If mbedtls_ctr_drbg_seed() is available in the mbedtls bulid then so should
be mbedtls_entropy_func(). Then it's up to the port to configure a valid
entropy source, eg via MBEDTLS_ENTROPY_HARDWARE_ALT.
Otherwise the "sock" member may have an undefined value if wrap_socket
fails with an exception and exits early, and then if the finaliser runs it
will try to close an invalid stream object.
Fixes issue #3828.
This matches CPython behaviour on Linux: a socket that is new and not
listening or connected is considered "hung up".
Thanks to @rkojedzinszky for the initial patch, PR #3457.
Textualy, the files in lib/uzlib/src were identical to the ones committed
in extmod/uzlib so there should be no behavioral change possible as a
result of this commit.
.. this maybe should be subject to MICROPY_CPYTHON_COMPAT, except that
is not defined in the main circuitpython ports so it would be a change
that makes no difference.
The order of function calls in an arithmetic expression is undefined and so
they must be written out as sequential statements.
Thanks to @dv-extrarius for reporting this issue, see issue #3690.
.. this maybe should be subject to MICROPY_CPYTHON_COMPAT, except that
is not defined in the main circuitpython ports so it would be a change
that makes no difference.
The 2nd and 3rd args of the ternary operator are treated like they are in
the same expression and must have similar types. void is not compatible
with int so that's why the compiler is complaining.
This patch moves the implementation of stream closure from a dedicated
method to the ioctl of the stream protocol, for each type that implements
closing. The benefits of this are:
1. Rounds out the stream ioctl function, which already includes flush,
seek and poll (among other things).
2. Makes calling mp_stream_close() on an object slightly more efficient
because it now no longer needs to lookup the close method and call it,
rather it just delegates straight to the ioctl function (if it exists).
3. Reduces code size and allows future types that implement the stream
protocol to be smaller because they don't need a dedicated close method.
Code size reduction is around 200 bytes smaller for x86 archs and around
30 bytes smaller for the bare-metal archs.
These allow accessing the filesystem label. For instance,
in boot.py, you can set the label on the built-in storage with:
storage.remount('/', False)
storage.getmount('/').label = "NEWLABEL"
storage.remount('/', True)
Users with multiple CIRCUITPY boards may find it desirable to
choose a different label for each board they own.
CPython doesn't allow SEEK_CUR with non-zero offset for files in text mode,
and uPy inherited this behaviour for both text and binary files. It makes
sense to provide full support for SEEK_CUR of binary-mode files in uPy, and
to do this in a minimal way means also allowing to use SEEK_CUR with
non-zero offsets on text-mode files. That seems to be a fair compromise.
This patch takes the software SPI implementation from extmod/machine_spi.c
and moves it to a dedicated file in drivers/bus/softspi.c. This allows the
SPI driver to be used independently of the uPy runtime, making it a more
general component.
This patch eliminates heap allocation in the VFS FAT disk IO layer, when
calling the underlying readblocks/writeblocks methods. The bytearray
object that is passed to these methods is now allocated on the C stack
rather than the heap (it's only 4 words big).
This means that these methods should not retain a pointer to the buffer
object that is passed in, but this was already a restriction because the
original heap-allocated bytearray had its buffer passed by reference.
This patch just moves the definition of the wrapper object fat_vfs_open_obj
to the location of the definition of its function, which matches how it's
done in most other places in the code base.
The fat_vfs_ilistdir2() function was only used by fat_vfs_ilistdir_func()
so moving the former into the same file as the latter allows it to be
placed directly into the latter function, thus saving code size.
CPython doesn't allow SEEK_CUR with non-zero offset for files in text mode,
and uPy inherited this behaviour for both text and binary files. It makes
sense to provide full support for SEEK_CUR of binary-mode files in uPy, and
to do this in a minimal way means also allowing to use SEEK_CUR with
non-zero offsets on text-mode files. That seems to be a fair compromise.
Dramatically improves TCP sending throughput because without an explicit
call to tcp_output() the data is only sent to the lower layers via the
lwIP slow timer which (by default) ticks every 500ms.
Before this patch MP_BINARY_OP_IN had two meanings: coming from bytecode it
meant that the args needed to be swapped, but coming from within the
runtime meant that the args were already in the correct order. This lead
to some confusion in the code and comments stating how args were reversed.
It also lead to 2 bugs: 1) containment for a subclass of a native type
didn't work; 2) the expression "{True} in True" would illegally succeed and
return True. In both of these cases it was because the args to
MP_BINARY_OP_IN ended up being reversed twice.
To fix these things this patch introduces MP_BINARY_OP_CONTAINS which
corresponds exactly to the __contains__ special method, and this is the
operator that built-in types should implement. MP_BINARY_OP_IN is now only
emitted by the compiler and is converted to MP_BINARY_OP_CONTAINS by
swapping the arguments.
It's possible to use the methods (eg ilistdir) of a VFS FatFS object
without it being mounted in the VFS itself. This previously worked but
only because FatFS was "mounting" the filesystem automatically when any
function (eg f_opendir) was called. But it didn't work for ports that used
synchronisation objects (_FS_REENTRANT) because they are only initialised
via a call to f_mount. So, call f_mount explicitly when creating a new
FatFS object so that everything is set up correctly. Then also provide a
finaliser to do the f_umount call, but only if synchronisation objects are
enabled (since otherwise the f_umount call does nothing).
This patch simplifies the str creation API to favour the common case of
creating a str object that is not forced to be interned. To force
interning of a new str the new mp_obj_new_str_via_qstr function is added,
and should only be used if warranted.
Apart from simplifying the mp_obj_new_str function (and making it have the
same signature as mp_obj_new_bytes), this patch also reduces code size by a
bit (-16 bytes for bare-arm and roughly -40 bytes on the bare-metal archs).
The SHA1 hashing functionality is provided via the "axtls" library's
implementation, and hence is unavailable when the "axtls" library is not being
used. This change provides the same SHA1 hashing functionality when using the
"mbedtls" library by using its implementation instead.
Introduction of ports subdirectory where all ports are moved to
The main change in this release is the introduction of a "ports/"
subdirectory at the top-level of the repository, and all of the ports are
moved here. In the process the "stmhal" port is renamed to "stm32" to
better reflect the MCU that it targets. In addition, the STM32 CMSIS and
HAL sources are moved to a new submodule called "stm32lib".
The bytecode has changed in this release, compared to the previous release,
and as a consequence the .mpy version number has increased to version 3.
This means that scripts compiled with the previous mpy-cross must be
recompiled to work with this new version.
There have also been various enhancements and optimisations, such as:
check for valid UTF-8 when creating str objects, support for reverse
special binary operations like __radd__, full domain checking in the math
module, support for floor-division and modulo in the viper emitter,
and addition of stack overflow checking when executing a regex.
The stm32 port sees improved support for F7 MCUs, addition of a new board
B_L475E_IOT01A based on the STM32L475, and support for the Wiznet W5500
chipset along with improved socket behaviour.
A detailed list of changes follows.
py core:
- objstr: startswith, endswith: check arg to be a string
- nlrx86,x64: replace #define of defined() with portable macro usage
- objtype: handle NotImplemented return from binary special methods
- objtype: mp_obj_class_lookup: improve debug logging
- map: remove unused new/free functions
- make m_malloc_fail() have void return type, since it doesn't return
- modstruct: in struct.pack, stop converting if there are no args left
- modstruct: check and prevent buffer-read overflow in struct unpacking
- modstruct: check and prevent buffer-write overflow in struct packing
- nlrthumb: get working again on standard Thumb arch (ie not Thumb2)
- objfloat: fix binary ops with incompatible objects
- obj: fix comparison of float/complex NaN with itself
- objtype: implement fallback for instance inplace special methods
- objtuple: properly implement comparison with incompatible types
- objstr: add check for valid UTF-8 when making a str from bytes
- objlist: properly implement comparison with incompatible types
- runtime0.h: move relational ops to the beginning of mp_binary_op_t
- runtime0.h: move MP_BINARY_OP_DIVMOD to the end of mp_binary_op_t
- objtype: make sure mp_binary_op_method_name has full size again
- runtime0.h: put inplace arith ops in front of normal operations
- builtinhelp: simplify code slightly by extracting object type
- runtime: implement dispatch for "reverse op" special methods
- nlrx86: fix building for Android/x86
- builtinhelp: change signature of help text var from pointer to array
- runtime.h: change empty mp_warning macro so var-args are non empty
- modbuiltins: implement abs() by dispatching to MP_UNARY_OP_ABS
- {objfloat,objcomplex}: optimise MP_UNARY_OP_ABS by reusing variables
- mpconfig.h: add note that using computed gotos in VM is not C99
- objstr: strip: don't strip "\0" by default
- objexcept: prevent infinite recursion when allocating exceptions
- stream: remove unnecessary checks for NULL return from vstr_add_len
- vstr: raise a RuntimeError if fixed vstr buffer overflows
- vm: use lowercase letter at start of exception message
- persistentcode: define mp_raw_code_save_file() for any unix target
- add config option to print warnings/errors to stderr
- objfloat: support raising a negative number to a fractional power
- objset: simplify set and frozenset by separating their locals dicts
- objset: check that RHS of a binary op is a set/frozenset
- objset: include the failed key in a KeyError raised from set.remove
- objtype: change type of enum-to-qstr table to uint16_t to save space
- objstr: make empty bytes object have a null-terminating byte
- mpprint: only check for null string printing when NDEBUG not defined
- objtype: clean up unary- and binary-op enum-to-qstr mapping tables
- persistentcode: bump .mpy version number to version 3
- bc: update opcode_format_table to match the bytecode
- modmath: add full checks for math domain errors
- modmath: convert log2 macro into a function
- formatfloat: don't print the negative sign of a NaN value
- formatfloat: use standard isinf, isnan funcs instead of custom ones
- modbuiltins: use existing utf8_get_char helper in builtin ord func
- emitnative: implement floor-division and modulo for viper emitter
- objtype: use CPython compatible method name for sizeof
- objtype: fit qstrs for special methods in byte type
- objtype: define all special methods if requested
- objtype: introduce MICROPY_PY_ALL_INPLACE_SPECIAL_METHODS
extmod:
- modubinascii: only include uzlib/tinf.h when it's really needed
- modussl_mbedtls: allow to compile with MBEDTLS_DEBUG_C disabled
- machine_pinbase: put PinBase singleton in ROM
- re1.5: upgrade to v0.8.2, adds hook for stack overflow checking
- modure: add stack overflow checking when executing a regex
- uos_dupterm: update uos.dupterm() and helper funcs to have index
- uos_dupterm: swallow any errors from dupterm closing the stream
- vfs: replace VLA in proxy func with small, static sized array
- modussl: add finaliser support for ussl objects
- modussl_mbedtls: allow to compile with unix coverage build
lib:
- add new submodule, stm32lib containing STM32 CMSIS and HAL source
- embed/abort_: use mp_raise_msg helper function
- libm: fix tanhf so that it correctly handles +/- infinity args
- libm: remove implementation of log2f, use MP_NEED_LOG2 instead
- axtls: update, support for SSL_EAGAIN return code
- berkeley-db-1.xx: update, allow to override MINCACHE, DEFPSIZE
drivers:
- memory/spiflash: change from hard-coded soft SPI to generic SPI
- display/ssd1306.py: improve performance of graphics methods
- nrf24l01: make nRF24L01 test script more portable
- display/ssd1306: implement SSD1306_I2C poweron method
- display/ssd1306: make poweron() work the same with SSD1306_SPI
- wiznet5k: improve the performance of socket ops with threading
- wiznet5k: get low-level W5500 driver working
tools:
- upip: upgrade to 1.2.2
- pyboard: use repr() when quoting data in error messages
- pyboard: update docstring for additional device support
tests:
- object_new: better messages, check user __new__() method
- class_new: add checks for __init__ being called and other improvements
- class_new: add another testcase for __new__/__init__ interaction
- class_inplace_op: test for inplace op fallback to normal one
- run-bench-tests: update locations of executables, now in ports/
- class_reverse_op: test for reverse arith ops special methods
- run-tests: skip class_inplace_op for minimal profile
- run-tests: fix copy-paste mistake in var name
- cpydiff: add cases for locals() discrepancies
- extmod: add test for ure regexes leading to infinite recursion
- extmod: add test for '-' in character class in regex
- run-tests: close device under test using "finally"
- net_inet: update tls test to work with CPython and incl new site
unix port:
- rename modsocket.c to modusocket.c
- modusocket: remove #if MICROPY_SOCKET_EXTRA code blocks
- enable MICROPY_PY_REVERSE_SPECIAL_METHODS
stm32 port:
- modmachine: make machine.bootloader() work when MPU is enabled
- modmachine: improve support for sleep/deepsleep on F7 MCUs
- compute PLL freq table during build instead of at run time
- modmachine: for F7 MCU, save power by reducing internal volt reg
- boards/pllvalues.py: make script work with both Python 2 and 3
- Makefile: use lib/stm32lib instead of local cmsis and hal files
- remove cmsis and hal files, they are now a submodule
- Makefile: automatically fetch stm32lib submodule if needed
- update to new STM Cube HAL library
- fix clock initialisation of L4 MCUs
- rename stmhal port directory to stm32
- remove unused usbd_msc.c file
- boards: change remaining stm32f4xx_hal_conf.h to unix line ending
- boards: change linker scripts to use "K" instead of hex byte size
- boards: fix I2C1 pin mapping on NUCLEO_F401RE/F411RE boards
- i2c: when scanning for I2C devices only do 1 probe per address
- modnwwiznet5k: release the GIL on blocking network operations
- boards: add new board B_L475E_IOT01A based on STM32L475
- make-stmconst.py: make sure mpz const data lives in ROM
- timer: make pyb.Timer() instances persistent
- mpconfigport.h: add configuration for max periphs on L4 series
- usbdev: make the USBD callback struct const so it can go in ROM
- usbdev: change static function variable to non-static
- usbdev: put all CDC state in a struct
- usbdev: put all HID state in a struct
- usbdev: simplify CDC tx/rx buffer passing
- usbdev: simplify HID tx/rx buffer passing
- usbdev/core: add state parameter to all callback functions
- usbdev: put all state for the USB device driver in a struct
- usbdev: simplify pointers to MSC state and block dev operations
- usbdev: merge all global USB device state into a single struct
- usbdev: make device descriptor callbacks take a state pointer
- usbdev: move all the USB device descriptor state into its struct
- timer: enable ARPE so that timer freq can be changed smoothly
- modnwwiznet5k: get the IP address of an established socket
- boards: fix typos in stm32f767_af.csv table
- usbd_cdc_interface: don't reset CDC output buf on initialisation
- modnwwiznet5k: implement WIZNET5K.isconnected() method
- modusocket: make getaddrinfo() work when passed an IP address
- modusocket: return OSError(-2) if getaddrinfo fails
- mpconfigport.h: add MICROPY_THREAD_YIELD() macro
- modnwwiznet5k: add support for W5500 Ethernet chip
- modnwwiznet5k: increase SPI bus speed to 42MHz
- modnwwiznet5k: implement stream ioctl for the Wiznet driver
- mphalport: improve efficiency of mp_hal_stdout_tx_strn_cooked
- make uos.dupterm() conform to specs by using extmod version
cc3200 port:
- enable micropython.kbd_intr() method
- use standard implementation of keyboard interrupt
esp8266 port:
- rename axtls_helpers.c to posix_helpers.c
- posix_helpers: set ENOMEM on memory alloc failure
- set DEFPSIZE=1024, MINCACHE=3 for "btree" module
- esp_mphal: send data in chunks to mp_uos_dupterm_tx_strn
- modnetwork: add "bssid" keyword arg to WLAN.connect() method
- modules/webrepl_setup: add info about allowed password length
zephyr port:
- Makefile: revamp "test" target after ports were moved to ports/
- use CONFIG_NET_APP_SETTINGS to setup initial network addresses
- switch to interrupt-driven pull-style console
pic16bit port:
- add definition of SEEK_SET to unistd.h
docs:
- pyboard/tutorial: add "timeout=0" to UART in pass-through example
- more xrefs to "MicroPython port" in glossary
- library/network: fix ref to "socket" module (should be "usocket")
- machine.Signal: improve style/grammar and add usage example
- library: add description of "index" parameter to uos.dupterm()
- library/micropython: fix typo in RST formatting
- library/framebuf.rst: generalise constructor to all colour formats
- btree: describe page caching policy of the underlying implementation
- esp8266/tutorial: update neopixel with example of using 4 bbp
- library/network: clarify usage of "bssid" arg in connect() method
- pyboard/quickref: add info for Switch, RTC, CAN, Accel classes
- pyboard/tutorial: update now that yellow LED also supports PWM
- esp8266/quickref: add quickref info for RTC class
- library: add missing cross-ref links for classes in pyb module
- library/network: update docs to state that W5500 is supported
- uselect: document one-shot polling mode
- usocket: elaborate descriptions
- usocket: document inet_ntop(), inet_pton()
- library/network: add dhcp_hostname parameter
- reference/isr_rules: minor typo correction
- ussl: fix module name refs and use "MicroPython port" term
- esp8266/general: add section on TLS limitations
- usocket: document that settimeout() isn't supported by all ports
- ure: add "|" (alternative) to the list of supported operators
- reference/isr_rules.rst: add tutorial on use of micropython.schedule()
travis:
- use --upgrade when pip is installing cpp-coveralls
- update build command now that stm32 Wiznet config has changed
examples:
- hwconfig_console: add .on()/.off() methods
all:
- convert mp_uint_t to mp_unary_op_t/mp_binary_op_t where appropriate
- convert remaining "mp_uint_t n_args" to "size_t n_args"
- make new ports/ sub-directory and move all ports there
- update Makefiles and others to build with new ports/ dir layout
- remove inclusion of internal py header files
- use NULL instead of "" when calling mp_raise exception helpers
README:
- update "Dependencies" section
- add explicit section on contributing
- add gcc and arm-none-eabi-newlib to list of required components
.gitattributes:
- remove obsolete entries for stmhal/hal, stmhal/cmsis
- add entries for files that will move to ports/ dir
If SSL_EAGAIN is returned (which is a feature of MicroPython's axTLS fork),
return EAGAIN.
Original axTLS returns SSL_OK both when there's no data to return to user
yet and when the underlying stream returns EAGAIN. That's not distinctive
enough, for example, original module code works well for blocking stream,
but will infinite-loop for non-blocking socket with EAGAIN. But if we fix
non-blocking case, blocking calls to .read() will return few None's initially
(while axTLS progresses thru handshake).
Using SSL_EAGAIN allows to fix non-blocking case without regressing the
blocking one.
Note that this only handles case of non-blocking reads of application data.
Initial handshake and writes still don't support non-blocking mode and must
be done in the blocking way.
* Introduce a python script to generate the USB descriptor instead of
a bunch of C macros. In the future, we can use this dynamically in
CircuitPython.
* Add support for detecting read-only mass storage mounts.
Fixes#377
