This follows the pattern of other peripherals (I2C, SPI) to specify the
pins using pin objects instead of a pair of GPIO port and pin number. It
makes it easier to customise the UART pins for a particular board.
USB CDC no longer needs TIM3 (which was originally used for LED(4) PWM)
and so TIM3 has been freed for general purpose use by the user. Hence
LED(4) lost its PWM capabilities.
This patch reinstates the PWM capabilities using a semi-generic piece
of code which allows to configure a timer and PWM channel to use for any
LED. But the PWM capability is only configured if the LED is set to an
intensity between 1 and 254 (ie only when needed). In that case the
relevant timer is configured for PWM. It's up to the user to make sure
the timers are not used if PWM is active.
This patch also makes sure that PWM LEDs are turned off using standard
GPIO when calling led.off() or led.intensity(0), instead of just setting
the PWM counter to zero.
Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx
to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI
and NSS. This makes it the same as how I2C is configured.
This is refactoring to enable support for the two USB PHYs available on
some STM32F4 processors to be used at the same time. The F405/7 & F429
have two USB PHYs, others such as the F411 only have one PHY.
This has been tested separately on a pyb10 (USB_FS PHY) and F429DISC
(USB_HS PHY) to be able to invoke a REPL/USB. I have modified a PYBV10
to support two PHYs.
The long term objective is to support a 2nd USB PHY to be brought up as a
USB HOST, and possibly a single USB PHY to be OTG.
If RTC is already running at boot then it's left alone. Otherwise, RTC is
started at boot but startup function returns straight away. RTC startup
is then finished the first time it is used. Fallback to LSI if LSE fails
to start in a certain time.
Also included:
MICROPY_HW_CLK_LAST_FREQ
hold pyb.freq() parameters in RTC backup reg
MICROPY_HW_RTC_USE_US
option to present datetime sub-seconds in microseconds
MICROPY_HW_RTC_USE_CALOUT
option to enable RTC calibration output
CLK_LAST_FREQ and RTC_USE_CALOUT are enabled for PYBv1.0.
Each board now needs an mpconfigboard.mk file which defines AF_FILE and
LD_FILE.
Also moved stm32f405.ld to boards/ directory to keep things organised.
This config option is for the USB OTG pin, pin A10. This is used on
some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it
shouldn't be used for OTG ID (actually PA10 is multiplexed on this
board, but defaults to LED(2)).
Partially addresses issue #1059.
Since all currently supported boards use pin A9 for this function, the
value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used,
just the fact that it is defined.
Addresses issue #1048.
Pulled in and modified work done by mux/iabdalkader on cc3k driver, from
iabdalkader-cc3k-update branch. That branch was terribly messy and had
too many conflicts to merge neatly.
This patch updates ST's HAL to the latest version, V1.3.0, dated 19 June
2014. Files were copied verbatim from the ST package. Only change was
to suppress compiler warning of unused variables in 4 places.
A lot of the changes from ST are cosmetic: comments and white space.
Some small code changes here and there, and addition of F411 header.
Main code change is how SysTick interrupt is set: it now has a
configuration variable to set the priority, so we no longer need to work
around this (originall in system_stm32f4xx.c).
This renames MICROPY_HW_HAS_WLAN to MICROPY_HW_ENABLE_CC3K (since it's a
driver, not a board feature) and wraps all CC3000 code in this #if.
It's disabled for all boards.
It's not enabled by default because it doesn't fully work. It can
connect to an AP, get an IP address and do a host-lookup, but not yet do
send or recv on a socket.
All board config macros now begin with MICROPY_HW_.
Renamed PYBv10 to PYBV10, since macros should be all uppercase.
Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD
detect pin can be easily configured.
