Commit Graph

15 Commits

Author SHA1 Message Date
iabdalkader 7649f5fbd2 stm32/sdram: Make SDRAM test cache aware, and optional failure with msg.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
2021-07-22 16:47:49 +10:00
Damien George 61f91de361 stm32/sdram: Prevent array-bounds warnings with GCC 11.
Signed-off-by: Damien George <damien@micropython.org>
2021-06-10 22:48:54 +10:00
8bitgeek fc6ea28d00 stm32/sdram: Make MICROPY_HW_FMC_BA1,MICROPY_HW_FMC_A11 optional pins.
This supports SDRAM having only 2 internal banks (using BA0 only), and only
11 (A0-A10) bits of address, such as IS42S16100H (512K x 16bit x 2bank).
2021-04-14 11:06:32 +10:00
iabdalkader b603066bc2 stm32/sdram: Add SDRAM enter/leave self-refresh mode functions.
These functions enable SDRAM data retention in stop mode.  Example usage,
in mpconfigboard.h:

    #define MICROPY_BOARD_ENTER_STOP sdram_enter_low_power();
    #define MICROPY_BOARD_LEAVE_STOP sdram_leave_low_power();
2020-12-17 23:19:25 +11:00
Damien George 69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Andrew Leech ff9a61b5a8 stm32/sdram: Expose the result of sdram startup test in stm32_main.
This means boards can choose to only use it for gc heap if the test passes.
2020-02-04 18:18:41 +11:00
Andrew Leech 19ca025b45 stm32/sdram: Fix to use new mpu_config_start/mpu_config_end signature. 2019-10-22 22:02:06 +11:00
Damien George eca4115f66 stm32/sdram: Use MPU helper functions to configure MPU for SDRAM use. 2019-07-03 01:27:33 +10:00
Andrew Leech 1470184bdd stm32/sdram: Update MPU settings to block invalid region, change attrs.
Set the active MPU region to the actual size of SDRAM configured and
invalidate the rest of the memory-mapped region, to prevent errors due to
CPU speculation.  Also update the attributes of the SDRAM region as per ST
recommendations, and change region numbers to avoid conflicts elsewhere in
the codebase (see eth usage).
2019-05-24 15:55:00 +10:00
Andrew Leech 8ed4a28dae stm32/sdram: Increase GPIO speed for SDRAM interface to "very high".
Currently all usages of mp_hal_pin_config_alt_static() set the pin speed to
"high" (50Mhz).  The SDRAM interface typically runs much faster than this
so should be set to the maximum pin speed.

This commit adds mp_hal_pin_config_alt_static_speed() which allows setting
the pin speed along with the other alternate function details.
2019-02-20 16:54:32 +11:00
Damien George 9639e0d26f stm32/sdram: Add support for 32-bit wide data bus and 256MB in MPU cfg. 2018-09-20 11:29:37 +10:00
forester3 e562f99263 stm32/sdram: Allow additional config by a board, and tune MPU settings.
- Allow configuration by a board of autorefresh number and burst length.
- Increase MPU region size to 8MiB.
- Make SDRAM region cacheable and executable.
2018-08-14 16:00:14 +10:00
Andrew Leech 968fa47392 stm32/sdram: On F7 MCUs enable MPU on external SDRAM.
This prevents hard-faults on non-aligned accesses.

Reference: http://www.keil.com/support/docs/3777.htm
2018-07-23 23:15:18 +10:00
Andrew Leech a1db1506a2 stm32/sdram: Integrate SDRAM driver into rest of code.
If SDRAM is configured and enabled for a board then it is used for the
MicroPython GC heap.
2018-07-23 23:14:23 +10:00
Andrew Leech 7ae053abfd stm32/sdram: Add SDRAM driver from OpenMV project.
Taken from 7fbe54ad4e/src/omv/sdram.c

Code is is MIT licensed.
2018-07-23 23:13:24 +10:00