The RT1176 has two cores, but the actual firmware supports only the CM7.
There are currently no good plans on how to use the CM4.
The actual MIMXRT1170_EVK board is on par with the existing MIMXRT boards,
with the following extensions:
- Use 64 MB RAM for the heap.
- Support both LAN interfaces as LAN(0) and LAN(1), with LAN(1)
being the 1GB interface.
The dual LAN port interface can eventually be adapted as well for the
RT1062 MCU.
This work was done in collaboration with @alphaFred.
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle. The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.
Extensions: support PWM for channel pairs. Channel pairs are declared by
supplying 2-element tuples for the pins. The two channels of a pair must
be the A/B channel of a FLEXPWM module. These form than a complementary
pair.
Additional supported keyword arguments:
- center=value Defines the center position of a pulse within the pulse
cycle. The align keyword is actually shortcut for center.
- sync=True|False: If set to True, the channels will be synchronized to a
submodule 0 channel, which has already to be enabled.
- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
channels are Center-Aligned or Edge-aligned. The channels must be either
complementary a channel pair or a group of synchronized channels. It may
as well be applied to a single channel, but withiout any benefit.
- invert= 0..3. Controls ouput inversion of the pins. Bit 0 controls the
first pin, bit 1 the second.
- deadtime=time_ns time of complementary channels for delaying the rising
slope.
- xor=0|1|2 xor causes the output of channel A and B to be xored. If
applied to a X channel, it shows the value oif A ^ B. If applied to an A
or B channel, both channel show the xored signal for xor=1. For xor=2,
the xored signal is split between channels A and B. See also the
Reference Manual, chapter about double pulses. The behavior of xor=2 can
also be achieved using the center method for locating a pulse within a
clock period.
The output is enabled for board pins only.
CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output. That applies only to FLEXPWM pins. The
use of QTMR pins which are not board pins will be rejected.
As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
Adds support for SDRAM via `SEMC` peripheral. SDRAM support can be
enabled in the mpconfigboard.mk file by setting `MICROPY_HW_SDRAM_AVAIL`
to `1` and poviding the size of the RAM via `MICROPY_HW_FLASH_SIZE`.
When SDRAM support is enabled the whole SDRAM is currently used used
for MicroPython heap.
Signed-off-by: Philipp Ebensberger
- Configures `PLL2->PFD0` with **198MHz** as base clock of
`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!
SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.
Signed-off-by: Philipp Ebensberger
- modified pin type from pin_obj_t to machine_pin_obj_t
- created machine_pin.c
- implemented basic version of make-pins.py to genertate pins.c/.h files
automatically; the only alternate function currently supported is GPIO
- added af.csv files for all supported MCUs
- replaced pins.c/pins.h files with pin.csv for all boards
- implemented on/off/high/low/value/init methods
- Implemented IN/OUT/OPEN_DRAIN modes
- modified LDFLAGS for DEBUG build to get usefull .elf file for debugging
Signed-off-by: Philipp Ebensberger
