This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
The nrf52840-mdk-usb-dongle and pca10050 comes with a pre-flashed
bootloader (OpenBootloader).
This commit updates the boards "mpconfigboard.mk" to use DFU as
default flashing method and set the corresponding BOOTLOADER
settings such that nrf52840_open_bootloader_1.2.x.ld linker
script is used.
The default DFU flashing method can be disabled by issuing "DFU=0"
when invoking make. This will lead to "segger" being used as default
flashing tool. When using "DFU=0", the linker scripts will not
compensate for any MBR and Bootloader region being present, and might
overwrite them if they were present.
The commit also removes the custom linker script specific to
nrf52840-mdk-usb-dongle as it now points to a generic.
Updated nrf52840-mdk-usb-dongle's README.md to be more clear on
how to deploy the built firmware.
The port README.md has also been updated. In the list of target
boards a new column has been added to indicate which bootloader
is present on the target board. And for consistency, changed all
examples in the README.md to use "deploy" instead of "flash".
Adding variables that can be set from other linker scripts:
- _bootloader_head_size:
Bootloader flash offset in front of the application.
- _bootloader_tail_size:
Bootloader offset from the tail of the flash.
In case the bootloader is located at the end.
- _bootloader_head_ram_size:
Bootloader RAM usage in front of the application.
Updated calculations of application flash and RAM.
Despite the [silk on the dock board](https://wiki.makerdiary.com/nrf52840-m2-devkit/resources/nrf52840_m2_devkit_hw_diagram_v1_0.pdf), the SDA/SCL pins weren't defined. Though, they were already defined in `mpconfigboard.h`.
Same for RX/TX. It looks like it declared `TXD` and `RXD`, so I didn't want to remove those, but I think it makes sense to have the "standard" pin names, but I moved ithem to illustrate they were all referencing the same pins.
I mimicked the whitespace I saw in the metro_nrf52840_express port.
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
We're moving towards a co-processor model and a Wiznet library is
already available.
New native APIs will replace these for chips with networking like the
ESP32S2 but they won't be these.
new file: ports/nrf/boards/raytac_mdbt50q-db-40/bootloader/6.0.0/pca10056_bootloader_6.0.0_s140.zip
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.h
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.mk
new file: ports/nrf/boards/raytac_mdbt50q-db-40/pins.c
Testing performed: That a card is successfully mounted on Pygamer with
the built in SD card slot
This module is enabled for most FULL_BUILD boards, but is disabled for
samd21 ("M0"), litex, and pca10100 for various reasons.
This enables WDT support for Simmel. Other platforms cannot yet use
WDT because it overflows their flash storage.
Enable CIRCUITPY_WDT support for the nrf target.
Signed-off-by: Sean Cross <sean@xobs.io>
With the WDT changes, building Circuit Python results in the following error:
/opt/gcc-arm-none-eabi-9-2019-q4-major/bin/../lib/gcc/arm-none-eabi/9.2.1/../../../../arm-none-eabi/bin/ld: section .ARM.exidx LMA [00000000000621c8,00000000000621cf] overlaps section .data LMA [00000000000621c8,0000000000062383]
This is because unwinding data is getting generated, but has nowhere to go.
Re-enable this data in the linker script so it is saved.
Signed-off-by: Sean Cross <sean@xobs.io>
This section immediately follows the .bss section, and is designed to
contain uninitialized variables that should persist across reboots.
The section is placed directly after .bss, under the theory that the
size of Circuit Python's .bss + .data is bigger than the bootloader's
.bss + .data, so there is less likely to be a conflict.
Signed-off-by: Sean Cross <sean@xobs.io>
Commit 6cea369b89 updated the TinyUSB
submodule to a version based on nrfx v2.0.0. This commit updates the nrf
port to work with the latest TinyUSB and nrfx v2.0.0.
Simmel had USB HID disabled in order to save space. However, the board
configuration did not set USB_DEVICES, causing it to inherit the default
device bouquet of MSC,CDC,MIDI,HID. This in turn caused HID to be included
in the USB Configuration Descriptor.
For some reason, this was not a problem in an earlier version of tinyusb or
circuitpython. However, in the most recent version this has rightfully
caused asserts to appear during configuration.
Re-enable USB_HID for now, as it doesn't add too much in terms of space.
We may disable it again later on if we become pressed for space.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds preliminary support for the nRF52833, which is a variant of
the nRF52840 with half the RAM, half the flash, and fewer peripherals.
Signed-off-by: Sean Cross <sean@xobs.io>
Now that error string compression is supported it's more important to have
consistent error string formatting (eg all lowercase English words,
consistent contractions). This commit cleans up some of the strings to
make them more consistent.
The "random" module no longer uses the hardware RNG (the extmod version of
this module has a pseudo-random number generator), so the config option
MICROPY_PY_RANDOM_HW_RNG is no longer meaningful. This commit replaces it
with MICROPY_HW_ENABLE_RNG, which controls whether the hardware RNG is
included in the build.
The backlight enable is active low on our board so the driver doesn't like it.
Toggling to GPIO manually for now.
As fixed the improper SPI bus pins definitions and it works!
Signed-off-by: Michael Welling <mwelling@ieee.org>
PacketBuffer facilitates packet oriented BLE protocols such as BLE
MIDI and the Apple Media Service.
This also adds PHY, MTU and connection event extension negotiation
to speed up data transfer when possible.
This allows the board to disable the onboard speaker until explicitly
enabled in user code.
Testing performed on a CPB:
* Touching the AUDIO pin with a fingertip no longer generates noise/buzz
* Generating a waveform with `simpleio.tone` produces no sound by default
* When the board.SPEAKER_ENABLE is configured as a digital output and
set True, `simpleio.tone` does produce sound
Note that while guides should include information about SPEAKER_ENABLE, it's
possible that some users who omitted it could view this as a breaking change.
They can fix it by simply adding code similar to
speaker_enable = digitalio.DigitalInOut(board.SPEAKER_ENABLE)
speaker_enable.direction = digitalio.Direction.OUTPUT
speaker_enable.value = True
before using the internal speaker.
Closes: #2258
This PR refines the _bleio API. It was originally motivated by
the addition of a new CircuitPython service that enables reading
and modifying files on the device. Moving the BLE lifecycle outside
of the VM motivated a number of changes to remove heap allocations
in some APIs.
It also motivated unifying connection initiation to the Adapter class
rather than the Central and Peripheral classes which have been removed.
Adapter now handles the GAP portion of BLE including advertising, which
has moved but is largely unchanged, and scanning, which has been enhanced
to return an iterator of filtered results.
Once a connection is created (either by us (aka Central) or a remote
device (aka Peripheral)) it is represented by a new Connection class.
This class knows the current connection state and can discover and
instantiate remote Services along with their Characteristics and
Descriptors.
Relates to #586
This patch add basic building blocks for nrf9P60.
It also includes a secure bootloader which forwards all
possible peripherals that are user selectable to become
non-secure. After configuring Flash, RAM and peripherals
the secure bootloader will jump to the non-secure domain
where MicroPython is placed.
The minimum size of a secure boot has to be a flash
block of 32Kb, hence why the linker scripts are
offsetting the main application this much.
The RAM offset is set to 128K, to allow for later
integration of Nordic Semiconductor's BSD socket
library which reserves the range 0x20010000 - 0x2001FFFF.
Add support for pca10059 with REPL over tinyusb USB CDC.
The board also includes a board specific module that will
recover UICR->REGOUT0 in case this has been erased.
This initial support does not preserve any existing bootloader
on the pca10090 in case this was present, and expects to use all
available flash on the device.
It was previously not taking into account that the list of pins was sparse,
so using the wrong index. The boards/X/pins.csv was generating the wrong
data for machine.Pin.board.
As part of this fix rename the variables to make it more clear what the
list contains (only board pins).
Change static LED functions to lowercase names, and trim down source code
lines for variants of MICROPY_HW_LED_COUNT. Also rename configuration for
MICROPY_HW_LEDx_LEVEL to MICROPY_HW_LEDx_PULLUP to align with global PULLUP
configuration.
- IBK-BLYST-NANO: Breakout board
- IDK-BLYST-NANO: DevKit board with builtin IDAP-M CMSIS-DAP Debug JTAG,
RGB led
- BLUEIO-TAG-EVIM: Sensor tag board (environmental sensor
(T, H, P, Air quality) + 9 axis motion sensor)
Also, the LED module has been updated to support individual base level
configuration of each LED. If set, this will be used instead of the
common configuration, MICROPY_HW_LED_PULLUP. The new configuration,
MICROPY_HW_LEDX_LEVEL, where X is the LED number can be used to set
the base level of the specific LED.
Removing linker script for nrf52840 s140 v6.0.0 as pca10056
target board now points to the new v6.1.1. Also, removing the
entry from the download_ble_stack.sh script.
Removing linker script for nrf52832 s132 v6.0.0 as all target
boards now points to the new v6.1.1. Also, removing the entry
from the download_ble_stack.sh script.
