Commit 8a917ad2529ea3df5f47e2be5b4edf362d2d03f6 added the gpio_reset_pin()
call to make sure that pins that were used as ADC inputs could subsequently
be used as digital IO. But calling gpio_reset_pin() will enable the
pull-up on the pin and so pull it high for a brief period. Instead use
rtc_gpio_deinit() which will just reconfigure the pin as a digital IO and
do nothing else.
Fixes issue #7079 (see also #5771).
Signed-off-by: Damien George <damien@micropython.org>
This is handy for remote characteristics because it allows for
the PacketBuffer binding code to have the correct max size. This
PR also adds checks so we don't write outside the outgoing buffer.
For an unconnected TCP socket, poll should return WR|HUP and read should
raise ENOTCONN. This is implemented by this commit and now the following
tests pass on esp32: extmod/usocket_tcp_basic.py,
net_hosted/connect_poll.py.
Signed-off-by: Damien George <damien@micropython.org>
This change allows running the tests in tests/basics/ without any failures
(but some tests are still skipped).
Signed-off-by: Damien George <damien@micropython.org>
This fixes `error: variable 'subpkg_tried' might be clobbered by 'longjmp'
or 'vfork' [-Werror=clobbered]` when compiling on ppc64le and aarch64 (and
possibly other architectures/toolchains).
This function includes the UART prescaler in the calculation (if it has
one, eg on H7 and WB MCUs).
Signed-off-by: Damien George <damien@micropython.org>
The STM32WB has a problem when address resolution is enabled: under certain
conditions the MCU can get into a state where it draws an additional 10mA
or so and eventually ends up with a broken BLE RX path in the silicon. A
simple way to reproduce this is to enable address resolution (which is the
default for NimBLE) and start the device advertising. If there is enough
BLE activity in the vicinity then the device will at some point enter the
bad state and, if left long enough, will have permanent BLE RX damage.
STMicroelectronics are aware of this issue. The only known workaround at
this stage is to not enable address resolution, which is implemented by
this commit.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, if C2 was busy (eg lots of BLE activity) then it may
not have had time to respond to the notification on the IPCC_CH_MM channel
by the time additional memory was available to put on that buffer. In such
a case C1 would modify the free buffer list while C2 was potentially
accessing it, and this would eventually lead to lost memory buffers (or a
corrupt linked list). If all buffers become lost then ACL packets
(asynchronous events) can no longer be delivered from C2 to C1.
This commit fixes this issue by waiting for C2 to indicate that it has
finished using the free buffer list.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
This change allows to build firmware for different rp2-based boards,
following how it is done in other ports like stm32 and esp32. So far only
the original Pico and Adafruit Feather RP2040 are added. Board names
should match (sans case) those in pico-sdk/src/boards/include/boards/.
Usage: Pico firmware can be build either using make as previously (it is
the default board) or by `make BOARD=PICO`. Feather is built by `make
BOARD=ADAFRUIT_FEATHER_RP2040`. Only the board name and flash drive size
is set, pin definition is taken from the appropriate pico-sdk board
definition. Firmware is saved in the directory build-BOARD_NAME.
Instantiation and init now support the rxbuf and txbuf keywords for setting
the buffer size. The default size is 256 bytes. The minimum and maximum
sizes are 32 and 32766 respectively.
uart.write() still includes checks for timeout, even if it is very unlikely
to happen due to a) lack of flow control support and b) the minimal timeout
values being longer than the time it needs to send a byte.
StateMachine.restart: Restarts the state machine
StateMachine.rx_fifo: Return the number of RX FIFO items, 0 if empty
StateMachine.tx_fifo: Return the number of TX FIFO items, 0 if empty
restart() seems to be the most useful one, as it resets the state machine
to the initial state without the need to re-initialise/re-create. It also
makes PIO code easier, because then stalling as an error state can be
unlocked.
rx_fifo() is also useful, for MP code to check for data and timeout if no
data arrived. Complex logic is easier handled in Python code than in PIO
code.
tx_fifo() can be useful to check states where data is not processed, and is
mostly for symmetry.
The implementation samples rosc.randombits at a frequency lower than the
oscillator frequency. This gives better random values. In addition, for
an 8-bit value 8 samples are taken and fed through a 8-bit CRC,
distributing the sampling over the byte. The resulting sampling rate is
about 120k/sec.
The RNG does not include testing of error conditions, like the ROSC being
in sync with the sampling or completely failing. Making the interim value
static causes it to perform a little bit better in short sync or drop-out
situations.
The output of uos.urandom() performs well with the NIST800-22 test suite.
In my trial it passed all tests of the sts 2.1.2 test suite. I also ran a
test of the random data with the Common Criteria test suite AIS 31, and it
passed all tests too.
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.
Signed-off-by: Alexander Ziubin aziubin@googlemail.com
