The index of machine_hw_spi_obj and machine_hw_spi_default_pins arrays is
assigned to 0 for ARG_id==HSPI_HOST and 1 for another SPI. On ESP32S2 and
S3 HSPI_HOST=2 so the first set (idx=0) of default pins is used for
SPI(id=2) aka HSPI/SPI3 and the second set (idx=1) for SPI(id=1) aka
FSPI/SPI2. This makes a misleading mess in MICROPY_HW_SPIxxxx definitions
and it is also in contradiction to the comments around the definitions.
Change the test of ARG_id to fix the order of machine_hw_spi_default_pins.
This change might require adjusting MICROPY_HW_SPIxxxx definitions in
mpconfigboard.h of S2/S3 based boards.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
- Move the qspi_xxxx_flash_config.c files to hal.
It turned out that they are less board than flash type specific.
- Change to a common flexspi_flash_config.h header file.
Thanks for the hint, Damien. The DEBUG build got very large recently.
The major difference is, that inline function are now inlined and
not included as a function. That's good and maybe bad. The good thing is,
that the code speed si now close to the final code. It could be worse
in single step debugging. I'll see.
Setting this option caused a new warning and a formatting error
to pop up at different places. Fixed as well.
The ID is read in a single function and used for:
- machine.unique_id()
- Ethernet MAC addresses.
- ...
That facilitates use of other MCU using a different access method for
the ID (e.g. i.MX RT1176).
Just another choice for the PHY interface.
Added: Keyword option phy_clock=LAN.IN or LAN.OUT
to define the source of the 50MHZ clock for the PHY
interface. The RMII clock is not enabled if it
is generated by a PYH board. Constants:
LAN.IN The clock is provided by the PHY board.
LAN.OUT The clock is provided by the MCU board.
The default is LAN.OUT or the value set in mpconfigboard.h, which
is currently set to IN only for the SEEED ARCH MIX board. Usage etc:
lan = LAN(phy_type=LAN.PHY_DP83848, phy_clock=LAN.IN)
The initial problem with a wrong ICMP checksum was caused by
the test code setting a checksum and the HW taking that probably as
the start value and ending up with 0xffff. With a checksum field of 0
set by the test code the HW creates the proper checksum.
Useful for boards without a PHY interface, where that has to be
attached. Like the Seed ARCH MIX board or Vision SOM. Phy drivers
supported so far are:
- KSZ8081
- DP83825
- LAN8720
More to come. Usage e.g.:
lan = LAN(phy_type=LAN.PHY_LAN8720, phy_addr=1)
The default values are those set in mpconfigboard.h.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
The pico-sdk 1.3.0 update in 97a7cc243b
introduced a change that broke RP2 Bluetooth UART, and possibly UART in
general, which stops working right after UART is initialized. The commit
raspberrypi/pico-sdk@2622e9b enables the UART receive timeout (RTIM) IRQ,
which is asserted when the receive FIFO is not empty, and no more
characters are received for a period of time.
This commit makes sure the RTIM IRQ is handled and cleared in
uart_service_interrupt.
The current ST HAL does not support reading the extended CSD so cannot
correctly detect the capacity of high-capacity cards. As a workaround, the
capacity can be forced via the MICROPY_HW_MMCARD_LOG_BLOCK_NBR config
option.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this new library version are:
- Update L4 HAL to v1.17.0.
- Add G4 HAL at v1.3.0.
- Add WL HAL at v1.1.0.
- Fix F4 UART and DMA data loss with RX hardware flow control.
- Optimise USB to pass config struct by reference.
- Fix bug in F4 MMC HAL_MMC_Erase function.
- Fix bug setting MMC relative address in F4 and F7 HAL.
Signed-off-by: Damien George <damien@micropython.org>
Any board with a board.json file will be built. ESP32-based boards will be
built using the IDF at $IDF_PATH_V42, all other MCU variants (S2, S3, C3)
will be built using the IDF at $IDF_PATH_V44.
Signed-off-by: Damien George <damien@micropython.org>
These were commented correctly by their colour, but in the wrong order with
respect to the PCB silkscreen.
Fixes issue #8054.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For the coverage build this reduces the binary size to about 1/4 of its
size, and seems to help gcov/lcov coverage analysis so that it doesn't miss
lines.
Signed-off-by: Damien George <damien@micropython.org>
The methods duty_u16() and duty_ns() are implemented to match the existing
docs. The duty will remain the same when the frequency is changed.
Standard ESP32 as well as S2, S3 and C3 are supported.
Thanks to @kdschlosser for the fix for rounding in resolution calculation.
Documentation is updated and examples expanded for esp32, including the
quickref and tutorial. Additional notes are added to the machine.PWM docs
regarding limitations of hardware PWM.
Instead of board pins, so that pins which have only the CPU specified in
pins.csv can still be used with mp_hal_pin_config_alt_static().
Signed-off-by: Damien George <damien@micropython.org>
A board can now define the following linker symbols to configure its flash
storage layout:
_micropy_hw_internal_flash_storage_start
_micropy_hw_internal_flash_storage_end
_micropy_hw_internal_flash_storage_ram_cache_start
_micropy_hw_internal_flash_storage_ram_cache_end
And optionally have a second flash segment by configuring
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE_SEGMENT2 to 1 and defining:
_micropy_hw_internal_flash_storage2_start
_micropy_hw_internal_flash_storage2_end
Signed-off-by: Damien George <damien@micropython.org>
The third and fourth parameters in display.rect() and display.fill_rect()
are not x,y coordinates, but are instead width,height values. Update the
comment after the example to show the correct x,y coordinates of the bottom
right corner of each rectangle, respectively.
