Also found a race condition between timer_disable and redraw, which
would happen if I debugger-paused inside common_hal_rgbmatrix_timer_disable
or put a delay or print inside it. That's what pausing inside reconstruct
fixes.
So that the "right timer" can be chosen, `timer_allocate` now gets the `self`
pointer. It's guaranteed at this point that the pin information is accurate,
so you can e.g., find a PWM unit related to the pins themselves.
This required touching each port to add the parameter even though it's
unused everywhere but raspberrypi.
The "word" referred to by BYTES_PER_WORD is actually the size of mp_obj_t
which is not always the same as the size of a pointer on the target
architecture. So rename this config value to better reflect what it
measures, and also prefix it with MP_.
For uses of BYTES_PER_WORD in setting the stack limit this has been
changed to sizeof(void *), because the stack usually grows with
machine-word sized values (eg an nlr_buf_t has many machine words in it).
Signed-off-by: Damien George <damien@micropython.org>
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Add "make submodules" to commands when building for the first time.
Otherwise, on a first time build, the submodules have not been checked out
and a lot of `fatal error: nrfx.h: No such file or directory` errors are
printed.
This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
The nrf52840-mdk-usb-dongle and pca10050 comes with a pre-flashed
bootloader (OpenBootloader).
This commit updates the boards "mpconfigboard.mk" to use DFU as
default flashing method and set the corresponding BOOTLOADER
settings such that nrf52840_open_bootloader_1.2.x.ld linker
script is used.
The default DFU flashing method can be disabled by issuing "DFU=0"
when invoking make. This will lead to "segger" being used as default
flashing tool. When using "DFU=0", the linker scripts will not
compensate for any MBR and Bootloader region being present, and might
overwrite them if they were present.
The commit also removes the custom linker script specific to
nrf52840-mdk-usb-dongle as it now points to a generic.
Updated nrf52840-mdk-usb-dongle's README.md to be more clear on
how to deploy the built firmware.
The port README.md has also been updated. In the list of target
boards a new column has been added to indicate which bootloader
is present on the target board. And for consistency, changed all
examples in the README.md to use "deploy" instead of "flash".
An additional Makefile parameter NRFUTIL_PORT can be set in order
to define the serial port to used for the DFU (Default: /dev/ttyACM0).
The "nrfutil" that is used as flasher towards OpenBootloader is
available for installation through Python "pip".
In case of SD=s140, SoftDevice ID 0xB6 is passed to nrfutil's package
generation which corresponds to SoftDevice s140 v6.1.1.
Add the option for "mpconfigboard.mk" to define whether the
board hosts a bootloader or not. The BOOTLOADER make variable
must be set to the name of the bootloader.
When the BOOTLOADER name is set it is also required to supply
the BOOTLOADER_VERSION_MAJOR and the BOOTLOADER_VERSION_MINOR
from the "mpconfigboards.mk". These will be used to resolve which
bootloader linker script that should be passed to the linker.
The BOOTLOADER section also supplies the C-compiler with
BOOTLOADER_<bootloader name>=<version major><version minor>
as a compiler define. This is for future use in case a bootloader
needs to do modification to the startup files or similar (like
setting the VTOR specific to a version of a bootloader).
Adding variables that can be set from other linker scripts:
- _bootloader_head_size:
Bootloader flash offset in front of the application.
- _bootloader_tail_size:
Bootloader offset from the tail of the flash.
In case the bootloader is located at the end.
- _bootloader_head_ram_size:
Bootloader RAM usage in front of the application.
Updated calculations of application flash and RAM.
This allows calls to `allocate_memory()` while the VM is running, it will then allocate from the GC heap (unless there is a suitable hole among the supervisor allocations), and when the VM exits and the GC heap is freed, the allocation will be moved to the bottom of the former GC heap and transformed into a proper supervisor allocation. Existing movable allocations will also be moved to defragment the supervisor heap and ensure that the next VM run gets as much memory as possible for the GC heap.
By itself this breaks terminalio because it violates the assumption that supervisor_display_move_memory() still has access to an undisturbed heap to copy the tilegrid from. It will work in many cases, but if you're unlucky you will get garbled terminal contents after exiting from the vm run that created the display. This will be fixed in the following commit, which is separate to simplify review.
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
I have a function where it should be impossible to reach the end, so I put in a safe-mode reset at the bottom:
```
int find_unused_slot(void) {
// precondition: you already verified that a slot was available
for (int i=0; i<NUM_SLOTS; i++) {
if( slot_free(i)) {
return i;
}
}
safe_mode_reset(MICROPY_FATAL_ERROR);
}
```
However, the compiler still gave a diagnostic, because safe_mode_reset was not declared NORETURN.
So I started by teaching the compiler that reset_into_safe_mode never returned. This leads at least one level deeper due to reset_cpu needing to be a NORETURN function. Each port is a little different in this area. I also marked reset_to_bootloader as NORETURN.
Additional notes:
* stm32's reset_to_bootloader was not implemented, but now does a bare reset. Most stm32s are not fitted with uf2 bootloaders anyway.
* ditto cxd56
* esp32s2 did not implement reset_cpu at all. I used esp_restart(). (not tested)
* litex did not implement reset_cpu at all. I used reboot_ctrl_write. But notably this is what reset_to_bootloader already did, so one or the other must be incorrect (not tested). reboot_ctrl_write cannot be declared NORETURN, as it returns unless the special value 0xac is written), so a new unreachable forever-loop is added.
* cxd56's reset is via a boardctl() call which can't generically be declared NORETURN, so a new unreacahble "for(;;)" forever-loop is added.
* In several places, NVIC_SystemReset is redeclared with NORETURN applied. This is accepted just fine by gcc. I chose this as preferable to editing the multiple copies of CMSIS headers where it is normally declared.
* the stub safe_mode reset simply aborts. This is used in mpy-cross.
Despite the [silk on the dock board](https://wiki.makerdiary.com/nrf52840-m2-devkit/resources/nrf52840_m2_devkit_hw_diagram_v1_0.pdf), the SDA/SCL pins weren't defined. Though, they were already defined in `mpconfigboard.h`.
Same for RX/TX. It looks like it declared `TXD` and `RXD`, so I didn't want to remove those, but I think it makes sense to have the "standard" pin names, but I moved ithem to illustrate they were all referencing the same pins.
I mimicked the whitespace I saw in the metro_nrf52840_express port.
The mpconfigport.h file is an internal header and should only ever be
included once by mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
This is a slight trade-off with code size, in places where a "_varg"
mp_raise variant is now used. The net savings on trinket_m0 is
just 32 bytes.
It also means that the translation will include the original English
text, and cannot be translated. These are usually names of Python
types such as int, set, or dict or special values such as "inf" or
"Nan".
Enabling the following features for all targets, except for nrf51
targets compiled to be used with SoftDevice:
- MICROPY_PY_ARRAY_SLICE_ASSIGN
- MICROPY_PY_SYS_STDFILES
- MICROPY_PY_UBINASCII
Splitting mpconfigport.h into multiple device specific
files in order to facilitate variations between devices.
Due to the fact that the devices might have variations in
features and also variations in flash size it makes sense
that some devices offers more functionality than others
without being limited by restricted devices.
For example more micropython features can be activated for
nrf52840 with 1MB flash, compared to nrf51 with 256KB.
We're moving towards a co-processor model and a Wiznet library is
already available.
New native APIs will replace these for chips with networking like the
ESP32S2 but they won't be these.
The motivation for doing this is so that we can allow
common_hal_mcu_disable_interrupts in IRQ context, something that works
on other ports, but not on nRF with SD enabled. This is because
when SD is enabled, calling sd_softdevice_is_enabled in the context
of an interrupt with priority 2 or 3 causes a HardFault. We have chosen
to give the USB interrupt priority 2 on nRF, the highest priority that
is compatible with SD.
Since at least SoftDevice s130 v2.0.1, sd_nvic_critical_region_enter/exit
have been implemented as inline functions and are safe to call even if
softdevice is not enabled. Reference kindly provided by danh:
https://devzone.nordicsemi.com/f/nordic-q-a/29553/sd_nvic_critical_region_enter-exit-missing-in-s130-v2
Switching to these as the default/only way to enable/disable interrupts
simplifies things, and fixes several problems and potential problems:
* Interrupts at priority 2 or 3 could not call common_hal_mcu_disable_interrupts
because the call to sd_softdevice_is_enabled would HardFault
* Hypothetically, the state of sd_softdevice_is_enabled
could change from the disable to the enable call, meaning the calls
would not match (__disable_irq() could be balanced with
sd_nvic_critical_region_exit).
This also fixes a problem I believe would exist if disable() were called
twice when SD is enabled. There is a single "is_nested_critical_region"
flag, and the second call would set it to 1. Both of the enable()
calls that followed would call critical_region_exit(1), and interrupts
would not properly be reenabled. In the new version of the code,
we use our own nesting_count value to track the intended state, so
now nested disable()s only call critical_region_enter() once, only
updating is_nested_critical_region once; and only the second enable()
call will call critical_region_exit, with the right value of i_n_c_r.
Finally, in port_sleep_until_interrupt, if !sd_enabled, we really do
need to __disable_irq, rather than using the common_hal_mcu routines;
the reason why is documented in a comment.
This commit adds time.ticks_ms/us support using RTC1 as the timebase. It
also adds the time.ticks_add/diff helper functions. This feature can be
enabled using MICROPY_PY_TIME_TICKS. If disabled the system uses the
legacy sleep methods and does not have any ticks functions.
In addition support for MICROPY_EVENT_POLL_HOOK was added to the
time.sleep_ms(x) function, making this function more power efficient and
allows support for select.poll/asyncio. To support this, the RTC's CCR0
was used to schedule a ~1msec event to wakeup the CPU.
Some important notes about the RTC timebase:
- Since the granularity of RTC1's ticks are approx 30usec, time.ticks_us is
not perfect, does not have 1us resolution, but is otherwise quite usable.
For tighter measurments the ticker's 1MHz counter should be used.
- time.ticks_ms(x) should *not* be called in an IRQ with higher prio than
the RTC overflow irq (3). If so it introduces a race condition and
possibly leads to wrong tick calculations.
See #6171 and #6202.
new file: ports/nrf/boards/raytac_mdbt50q-db-40/bootloader/6.0.0/pca10056_bootloader_6.0.0_s140.zip
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.h
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.mk
new file: ports/nrf/boards/raytac_mdbt50q-db-40/pins.c
When compiling for debug (-O0) the .text segment cannot fit the flash
region when MICROPY_ROM_TEXT_COMPRESSION=1, because the compiler does not
optimise away the large if-else chain used to select the correct compressed
string.
This commit enforces MICROPY_ROM_TEXT_COMPRESSION=0 when compiling for
debug (DEBUG=1).
The storage space of the advertisement name is not declared static, leading
to a random advertisement name. This commit fixes the issue by declaring
it static.
The Bluetooth link gets disconnected when connecting from a PC after 30-40
seconds. This commit adds handling of the data length update request. The
data length parameter pointer is set to NULL in the reply, letting the
SoftDevice automatically set values and use them in the data length update
procedure.
mp_keyboard_interrupt() triggers a compiler error because the function is
implicitly declared. This commit adds "py/runtime.h" to the includes.
Fixes issue #5732.
Testing performed: That a card is successfully mounted on Pygamer with
the built in SD card slot
This module is enabled for most FULL_BUILD boards, but is disabled for
samd21 ("M0"), litex, and pca10100 for various reasons.
* Fix flash writes that don't end on a sector boundary. Fixes#2944
* Fix enum incompatibility with IDF.
* Fix printf output so it goes out debug UART.
* Increase stack size to 8k.
* Fix sleep of less than a tick so it doesn't crash.
This pulls all common functionality into `shared-bindings` and keeps
platform-specific code inside `nrf`. Additionally, this performs most
validation in the `shared-bindings` site.
The only validation that occurs inside platform-specific `common-hal`
code is related to timeout limits that are platform-specific.
Additionally, all documentation is now inside the `shared-bindings`
directory.
Signed-off-by: Sean Cross <sean@xobs.io>
The previous setting of `1` meant that the bluetooth system couldn't be
used when the watchdog timer was enabled.
Signed-off-by: Sean Cross <sean@xobs.io>
As part of the reset process, save the current tick count to an
uninitialized memory location. That way, the current tick value will be
preserved across reboots.
A reboot will cause us to lose a certain number of ticks, depending on
how long a reboot takes, however if reboots are infrequent then this
will not be a large amount of time lost.
Signed-off-by: Sean Cross <sean@xobs.io>
For `microcontroller.reset()`, don't manually call NVIC_SystemReset().
Instead, call the `port_reset()` in case the port wants to do any
cleanup.
Signed-off-by: Sean Cross <sean@xobs.io>
This finishes the rework of the exception handler, which is once
again stored inside the watchdog timer module.
This also implements a `watchdog_reset()` that is used to disable the
RAISE watchdog, if one is enabled.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds an exception to be raised when the WatchDogTimer times out.
Note that this currently causes a HardFault, and it's not clear why it's
not behaving properly.
Signed-off-by: Sean Cross <sean@xobs.io>
This enables WDT support for Simmel. Other platforms cannot yet use
WDT because it overflows their flash storage.
Enable CIRCUITPY_WDT support for the nrf target.
Signed-off-by: Sean Cross <sean@xobs.io>
With the WDT changes, building Circuit Python results in the following error:
/opt/gcc-arm-none-eabi-9-2019-q4-major/bin/../lib/gcc/arm-none-eabi/9.2.1/../../../../arm-none-eabi/bin/ld: section .ARM.exidx LMA [00000000000621c8,00000000000621cf] overlaps section .data LMA [00000000000621c8,0000000000062383]
This is because unwinding data is getting generated, but has nowhere to go.
Re-enable this data in the linker script so it is saved.
Signed-off-by: Sean Cross <sean@xobs.io>
