Add address_little_endian for epaper displays with little endian
(low byte first) addresses.
Also clears allocated display and display bus memory so it has a
known state. The acep member wasn't always set so it varied
accidentally.
Fixes#7560. May fix#7778. Fixes#5119.
PicoDVI in CP support 640x480 and 800x480 on Feather DVI, Pico and
Pico W. 1 and 2 bit grayscale are full resolution. 8 and 16 bit
color are half resolution.
Memory layout is modified to give the top most 4k of ram to the
second core. Its MPU is used to prevent flash access after startup.
The port saved word is moved to a watchdog scratch register so that
it doesn't get overwritten by other things in RAM.
Right align status bar and scroll area. This normally gives a few
pixels of padding on the left hand side and improves the odds it is
readable in a case. Fixes#7562
Fixes c stack checking. The length was correct but the top was being
set to the current stack pointer instead of the correct top.
Fixes#7643
This makes Bitmap subscr raise IndexError instead of ValueError
when the index arguments are wrong.
- Move loading .js scripts from <head> to <body> for faster rendering
- Enable back-button support for file system/editor navigation
- Close WebSocket when navigating away from /cp/serial
- Use better looking Blinka icon.
In #7497 port_background_task was renamed to port_background_tick
but the actual call site wasn't changed. This meant that it was
no longer called!
Rename more functions from task to tick to make it clearer which is
which.
Fixes polling thread looping forever hangs preventing new connections.
Don't lose listening sockets on mp resets and re-init.
Keep better separation of "system" and "user" sockets.
Track socket states to prevent re-use of sockets before closed.
Close REST socket when transaction completes. No post-init.
Remove unnecessary state flags.
* Enable dcache for OCRAM where the VM heap lives.
* Add CIRCUITPY_SWO_TRACE for pushing program counters out over the
SWO pin via the ITM module in the CPU. Exempt some functions from
instrumentation to reduce traffic and allow inlining.
* Place more functions in ITCM to handle errors using code in RAM-only
and speed up CP.
* Use SET and CLEAR registers for digitalio. The SDK does read, mask
and write.
* Switch to 2MiB reserved for CircuitPython code. Up from 1MiB.
* Run USB interrupts during flash erase and write.
* Allow storage writes from CP if the USB drive is disabled.
* Get perf bench tests running on CircuitPython and increase timeouts
so it works when instrumentation is active.
This 2-in-1 PR started with the goal of support the Bangle.js 2
smartwatch with *no USB*.
* Adds "secure" DFU build support with a committed private key.
* Adds 3-bit color support with one dummy bit for the JDI memory display
* Allows nrf boards to have a board_background_task() run in RUN_BACKGROUND_TASK.
This is needed because the Bangle.js 2 uses the watchdog to reset.
* Renamed port_background_task() to port_background_tick() to indicate it
runs on tick, not RUN_BACKGROUND_TASK.
* Marks serial connected when the display terminal is inited. This means
that safe mode messages show up on the display.
ACep, 7-color epaper displays also pack 3 bits in 4. So, I added that
support as well.
* Adds 3-bit ACeP color support for 7-color e-paper displays. (Not
watch related but similar due to color depth.)
* Allows a refresh sequence instead of a single int command. The 7" ACeP
display requires a data byte for refresh.
* Adds optional delay after resetting the display. The ACeP displays
need this. (Probably to load LUTs from flash.)
* Adds a cleaning phase for ACeP displays before the real refresh.
For both:
* Add dither support to Palette.
* Palette no longer converts colors when set. Instead, it caches
converted colors at each index.
* ColorConverter now caches the last converted color. It should make
conversions faster for repeated colors (not dithering.)
* write any partial message
* instead of "..." show a sensible (translatable) message
This does slightly lower the amount of data that can be printed,
and makes the exact amount dependent on the language. However, if boot.py
intentionally needs to produce larger amounts of output, it can
deliberately mount the filesystem in RW mode and perform any writes needed.
In that case it's up to the boot.py to choose an appropriate way to
limit the number of writes if needed for the application.
Now, open wifi works on Pico W, so this closes#7438.
For the web workflow it's now OK to either
* specify an empty password string (as before)
* not have the CIRCUITPY_WIFI_PASSWORD key at all (new functionality)
This may help address #7409 if the underlying cause is the deterministic
volume ID. However, not all boards have working urandom (samd21
at least does not) so a couple of fallbacks are attempted when it fails.
I verified that on a pico_w, each `storage.erase_filesystem()` gives
a distinct 32-bit volume ID (pico_w's urandom can never fail)
