Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
F-strings, new machine.I2S class, ESP32-C3 support and LEGO_HUB_NO6 board
This release of MicroPython adds support for f-strings (PEP-498), with a
few limitations compared to normal Python. F-strings are essentially
syntactic sugar for "".format() and make formatting strings a lot more
convenient. Other improvements to the core runtime include pretty printing
OSError when it has two arguments (an errno code and a string), scheduling
of KeyboardInterrupt on the main thread, and support for a single argument
to the optimised form of StopIteration.
In the machine module a new I2S class has been added, with support for
esp32 and stm32 ports. This provides a consistent API for transmit and
receive of audio data in blocking, non-blocking and asyncio-based
operation. Also, the json module has support for the "separators" argument
in the dump and dumps functions, and framebuf now includes a way to blit
between frame buffers of different formats using a palette. A new,
portable machine.bitstream function is also added which can output a stream
of bits with configurable timing, and is used as the basis for driving
WS2812 LEDs in a common way across ports.
There has been some restructuring of the repository directory layout, with
all third-party code now in the lib/ directory. And a new top-level
directory shared/ has been added with first-party code that was previously
in lib/ moved there.
The docs have seen further improvement with enhancements and additions to
the rp2 parts, as well as a new quick reference for the zephyr port.
The terms master/slave have been replaced with controller/peripheral,
mainly relating to I2C and SPI usage. And u-module references have been
replaced with just the module name without the u-prefix to help clear up
the intended usage of modules in MicroPython.
For the esp8266 and esp32 ports, hidden networks are now included in WLAN
scan results. On the esp32 the RMT class is enhanced with idle_level and
write_pulses modes. There is initial support for ESP32-C3 chips with
GENERIC_C3 and GENERIC_C3_USB boards.
The javascript port has had its Makefile and garbage collector
implementation reworked so it compiles and runs with latest the Emscripten
using asyncify.
The mimxrt port sees the addition of hardware I2C and SPI support, as well
as some additional methods to the machine module. There is also support
for Hyperflash chips.
The nrf port now has full VFS storage support, enables source-line on
traceback, and has .mpy features consistent with other ports.
For the rp2 port there is now more configurability for boards, and more
boards added.
The stm32 port has a new LEGO_HUB_NO6 board definition with detailed
information how to get this LEGO Hub running stock MicroPython. There is
also now support to change the CPU frequency on STM32WB MCUs. And USBD_xxx
descriptor options have been renamed to MICROPY_HW_USB_xxx.
Thanks to everyone who contributed to this release: Amir Gonnen, Andrew
Scheller, Bryan Tong Minh, Chris Wilson, Damien George, Daniel Mizyrycki,
David Lechner, David P, Fernando, finefoot, Frank Pilhofer, Glenn Ruben
Bakke, iabdalkader, Jeff Epler, Jim Mussared, Jonathan Hogg, Josh Klar,
Josh Lloyd, Julia Hathaway, Krzysztof Adamski, Matúš Olekšák, Michael
Weiss, Michel Bouwmans, Mike Causer, Mike Teachman, Ned Konz, NitiKaur,
oclyke, Patrick Van Oosterwijck, Peter Hinch, Peter Züger, Philipp
Ebensberger, robert-hh, Roberto Colistete Jr, Sashkoiv, Seon Rozenblum,
Tobias Thyrrestrup, Tom McDermott, Will Sowerbutts, Yonatan Goldschmidt.
What follows is a detailed list of changes, generated from the git commit
history, and organised into sections.
Main components
===============
all:
- fix signed shifts and NULL access errors from -fsanitize=undefined
- update to point to files in new shared/ directory
py core:
- mpstate: make exceptions thread-local
- mpstate: schedule KeyboardInterrupt on main thread
- mperrno: add MP_ECANCELED error code
- makeqstrdefs.py: don't include .h files explicitly in preprocessing
- mark unused arguments from bytecode decoding macros
- objexcept: pretty print OSError also when it has 2 arguments
- makeversionhdr: add --tags arg to git describe
- vm: simplify handling of MP_OBJ_STOP_ITERATION in yield-from opcode
- objexcept: make mp_obj_exception_get_value support subclassed excs
- support single argument to optimised MP_OBJ_STOP_ITERATION
- introduce and use mp_raise_type_arg helper
- modsys: optimise sys.exit for code size by using exception helpers
- objexcept: make mp_obj_new_exception_arg1 inline
- obj: fix formatting of comment for mp_obj_is_integer
- emitnative: reuse need_reg_all func in need_stack_settled
- emitnative: ensure stack settling is safe mid-branch
- runtime: fix bool unary op for subclasses of native types
- builtinimport: fix condition for including do_execute_raw_code()
- mkrules: automatically build mpy-cross if it doesn't exist
- implement partial PEP-498 (f-string) support
- lexer: clear fstring_args vstr on lexer free
- mkrules.mk: do submodule sync in "make submodules"
extmod:
- btstack: add missing call to mp_bluetooth_hci_uart_deinit
- btstack: check that BLE is active before performing operations
- uasyncio: get addr and bind server socket before creating task
- axtls-include: add axtls_os_port.h to customise axTLS
- update for move of crypto-algorithms, re1.5, uzlib to lib
- moduselect: conditionally compile select()
- nimble: fix leak in l2cap_send if send-while-stalled
- btstack/btstack.mk: use -Wno-implicit-fallthrough, not =0
- utime: always invoke mp_hal_delay_ms when >= to 0ms
- modbluetooth: clamp MTU values to 32->UINT16_MAX
- nimble: allow modbluetooth binding to hook "sent HCI packet"
- nimble: add "memory stalling" mechanism for l2cap_send
- uasyncio: in open_connection use address info in socket creation
- modujson: add support for dump/dumps separators keyword-argument
- modlwip: fix close and clean up of UDP and raw sockets
- modbluetooth: add send_update arg to gatts_write
- add machine.bitstream
- modframebuf: enable blit between different formats via a palette
lib:
- tinyusb: update to version 0.10.1
- pico-sdk: update to version 1.2.0
- utils/stdout_helpers: make mp_hal_stdout_tx_strn_cooked efficient
- axtls: switch to repo at micropython/axtls
- axtls: update to latest axtls 2.1.5 wih additional commits
- re1.5: move re1.5 code from extmod to lib
- uzlib: move uzlib code from extmod to lib
- crypto-algorithms: move crypto-algorithms code from extmod to lib
- update README's based on contents of these dirs
drivers:
- neopixel: add common machine.bitstream-based neopixel module
- neopixel: optimize fill() for speed
- neopixel: reduce code size of driver
- cyw43: fix cyw43_deinit so it can be called many times in a row
- cyw43: make wifi join fail if interface is not active
mpy-cross:
- disable stack check when building with Emscripten
Support components
==================
docs:
- library: document new esp32.RMT features and fix wait_done
- library: warn that ustruct doesn't handle spaces in format strings
- esp8266/tutorial: change flash mode from dio to dout
- replace master/slave with controller/peripheral in I2C and SPI
- rp2: enhance quickref and change image to Pico pinout
- rp2: update general section to give a brief technical overview
- library/utime.rst: clarify behaviour and precision of sleep ms/us
- library/uasyncio.rst: document stream readexactly() method
- library/machine.I2S.rst: fix use of sd pin in examples
- zephyr: add quick reference for the Zephyr port
- library/zephyr: add libraries specific to the Zephyr port
- templates: add unix and zephyr quickref links to top-index
- rename ufoo.rst to foo.rst
- replace ufoo with foo in all docs
- library/index.rst: clarify module naming and purpose
- library/builtins.rst: add module title
- library/network.rst: simplify socket import
- add docs for machine.bitstream and neopixel module
- library: fix usage of :term: for frozen module reference
- esp8266: use monospace for software tools
- reference: mention that slicing a memoryview causes allocation
examples: no changes specific to this component/port
tests:
- extmod: make uasyncio_heaplock test more deterministic
- cpydiff/modules_struct_whitespace_in_format: run black
- extmod/ujson: add tests for dump/dumps separators argument
- run-multitests.py: add broadcast and wait facility
- multi_bluetooth/ble_subscribe.py: add test for subscription
- extmod/vfs_fat_finaliser.py: ensure alloc at never-used GC blocks
- basics: split f-string debug printing to separate file with .exp
- pybnative: make while.py test run on boards without pyb.delay
tools:
- autobuild: add scripts to build release firmware
- remove obsolete build-stm-latest.sh script
- ci.sh: run apt-get update in ci_powerpc_setup
- makemanifest.py: allow passing flags to mpy-tool.py
- autobuild: add mimxrt port to build scripts for nightly builds
- pyboard.py: add cmd-line option to make soft reset configurable
- mpremote: swap order of PID and VID in connect-list output
- ci.sh: build unix dev variant as part of macOS CI
- ci.sh: build GENERIC_C3 board as part of esp32 CI
- autobuild: use separate IDF version to build newer esp32 SoCs
- autobuild: add FeatherS2 and TinyS2 to esp32 auto builds
- mpremote: add seek whence for mounted files
- mpremote: raise OSError on unsupported RemoteFile.seek
- autobuild: add the MIMXRT1050_EVKB board to the daily builds
- ci.sh: add mpy-cross build to nrf port
- codeformat.py: include ports/nrf/modules/nrf in code formatting
- gen-cpydiff.py: don't rename foo to ufoo in diff output
- autobuild: add auto build for Silicognition wESP32
- mpremote: fix connect-list in case VID/PID are None
- mpremote: add "devs" shortcut for "connect list"
- mpremote: remove support for pyb.USB_VCP in/out specialisation
- autobuild: don't use "-B" for make, it's already a fresh build
- pyboard.py: move --no-exclusive/--soft-reset out of mutex group
- pyboard.py: make --no-follow use same variable as --follow
- pyboard.py: add --exclusive to match --no-exclusive
- pyboard.py: make --no-soft-reset consistent with other args
- uncrustify: force 1 newline at end of file
- mpremote: bump version to 0.0.6
CI:
- workflows: add workflow to build and test javascript port
- workflows: switch from Coveralls to Codecov
- workflows: switch from lcov to gcov
- workflows: add workflow to build and test unix dev variant
The ports
=========
all ports:
- use common mp_hal_stdout_tx_strn_cooked instead of custom one
- update for move of crypto-algorithms, uzlib to lib
- rename USBD_VID/PID config macros to MICROPY_HW_USB_VID/PID
bare-arm port: no changes specific to this component/port
cc3200 port: no changes specific to this component/port
esp8266 port:
- add __len__ to NeoPixel driver to support iterating
- Makefile: add more libm files to build
- include hidden networks in WLAN.scan results
- replace esp.neopixel with machine.bitstream
- remove dead code for end_ticks in machine_bitstream
esp32 port:
- boards/sdkconfig.base: disable MEMPROT_FEATURE to alloc from IRAM
- add __len__ to NeoPixel driver to support iterating
- main: allow MICROPY_DIR to be overridden
- esp32_rmt: fix RMT looping in newer IDF versions
- esp32_rmt: enhance RMT with idle_level and write_pulses modes
- add new machine.I2S class for I2S protocol support
- machine_spi: calculate actual attained baudrate
- machine_hw_spi: use a 2 item SPI queue for long transfers
- machine_dac: add MICROPY_PY_MACHINE_DAC option, enable by default
- machine_i2s: add MICROPY_PY_MACHINE_I2S option, enable by default
- fix use of mp_int_t, size_t and uintptr_t
- add initial support for ESP32C3 SoCs
- boards/GENERIC_C3: add generic C3-based board
- modmachine: release the GIL in machine.idle()
- mphalport: always yield at least once in delay_ms
- machine_uart: add flow kw-arg to enable hardware flow control
- boards: add Silicognition wESP32 board configuration
- mpconfigport.h: enable reverse and inplace special methods
- include hidden networks in WLAN.scan results
- makeimg.py: get bootloader and partition offset from sdkconfig
- enable MICROPY_PY_FSTRINGS by default
- machine_hw_spi: release GIL during transfers
- machine_pin: make check for non-output pins respect chip variant
- replace esp.neopixel with machine.bitstream
- remove dead code for end_ticks in machine_bitstream
- boards: add GENERIC_C3_USB board with USB serial/JTAG support
javascript port:
- rework Makefile and GC so it works with latest Emscripten
- Makefile: suppress compiler errors from array bounds
- Makefile: change variable to EXPORTED_RUNTIME_METHODS
mimxrt port:
- move calc_weekday helper function to timeutils
- machine_spi: add the SPI class to the machine module
- moduos: seed the PRNG on boot using the TRNG
- boards: set vfs partition start to 1 MBbyte
- main: skip running main.py if boot.py failed
- main: extend the information returned by help()
- mimxrt_flash: remove commented-out code
- modmachine: add a few minor methods to the machine module
- machine_led: use mp_raise_msg_varg helper
- machine_i2c: add hardware-based machine.I2C to machine module
- add support for Hyperflash chips
- boards: add support for the MIMXRT1050_EVKB board
- machine_pin: implement ioctl for Pin
minimal port:
- Makefile: add support for building with user C modules
nrf port:
- modules: replace master/slave with controller/peripheral in SPI
- boards/common.ld: calculate unused flash region
- modules/nrf: add new nrf module with flash block device
- drivers: add support for using flash block device with SoftDevice
- mpconfigport.h: expose nrf module when MICROPY_PY_NRF is set
- README: update README.md to reflect internal file systems
- mpconfigport.h: tune FAT FS configuration
- Makefile: add _fs_size linker script override from make
- modules/uos: allow a board to configure MICROPY_VFS_FAT/LFS1/LFS2
- mpconfigport.h: enable MICROPY_PY_IO_FILEIO when an FS is enabled
- qstrdefsport.h: add entries for in-built FS mount points
- main: add auto mount and auto format hook for internal flash FS
- boards: enable needed features for FAT/LFS1/LFS2
- facilitate use of freeze manifest
- boards: set FROZEN_MANIFEST blank when SD present on nrf51 targets
- modules/scripts: add file system formatting script
- Makefile: set default manifest file for all targets
- mphalport: add dummy function for mp_hal_time_ns()
- boards: enable MICROPY_VFS_LFS2 for all target boards
- modules/uos: add ilistdir to uos module
- modules/nrf: add function to enable/disable DCDC
- enable source line on tracebacks
- set .mpy features consistent with documentation and other ports
pic16bit port: no changes specific to this component/port
powerpc port: no changes specific to this component/port
qemu-arm port: no changes specific to this component/port
rp2 port:
- use 0=Monday datetime convention in RTC
- machine_rtc: in RTC.datetime, compute weekday automatically
- CMakeLists.txt: suppress compiler errors for pico-sdk and tinyusb
- tusb_config.h: set CFG_TUD_CDC_EP_BUFSIZE to 256
- machine_uart: add hardware flow control support
- machine_uart: allow overriding default machine UART pins
- machine_i2c: allow boards to configure I2C pins using new macros
- machine_spi: allow boards to configure SPI pins using new macros
- machine_uart: fix poll ioctl to also check hardware FIFO
- machine_uart: fix read when FIFO has chars but ringbuf doesn't
- tusb_port: allow boards to configure USB VID and PID
- boards/ADAFRUIT_FEATHER_RP2040: configure custom VID/PID
- boards/ADAFRUIT_FEATHER_RP2040: configure I2C/SPI default pins
- boards/SPARKFUN_PROMICRO: configure UART/I2C/SPI default pins
- boards/SPARKFUN_THINGPLUS: configure I2C/SPI default pins
- boards: add Adafruit ItsyBitsy RP2040
- boards: add Adafruit QT Py RP2040
- boards: add Pimoroni Pico LiPo 4MB
- boards: add Pimoroni Pico LiPo 16MB
- boards: add Pimoroni Tiny 2040
- CMakeLists.txt: allow a board's cmake to set the manifest path
- enable MICROPY_PY_FSTRINGS by default
- Makefile: add "submodules" target, to match other ports
- rp2_flash: disable IRQs while calling flash_erase/program
- CMakeLists.txt: add option to enable double tap reset to bootrom
- mpconfigport.h: allow boards to add root pointers
samd port:
- add support for building with user C modules
stm32 port:
- softtimer: add soft_timer_reinsert() helper function
- mpbthciport: change from systick to soft-timer for BT scheduling
- provide a custom BTstack runloop that integrates with soft timer
- usb: make irq's default trigger enable all events
- boardctrl: skip running main.py if boot.py had an error
- sdio: fix undefined reference to DMA stream on H7
- dma: add DMAMUX configuration for H7 to fix dma_nohal_init
- main: call mp_deinit() at end of main
- adc: allow using ADC12 and ADC3 for H7
- adc: define the ADC instance used for internal channels
- adc: simplify and generalise how pin_adcX table is defined
- add new machine.I2S class for I2S protocol support
- boards/NUCLEO_F446RE: fix I2C1 pin assignment to match datasheet
- replace master/slave with controller/peripheral in I2C and SPI
- systick: always POLL_HOOK when delaying for milliseconds
- sdram: make SDRAM test cache aware, and optional failure with msg
- boards/NUCLEO_F446RE: enable CAN bus support
- boards: add support for SparkFun STM32 MicroMod Processor board
- uart: fix LPUART1 baudrate set/get
- uart: support low baudrates on LPUART1
- boards/STM32F429DISC: set correct UART2 pins and add UART3/6
- boards/NUCLEO_F439ZI: add board definition for NUCLEO_F439ZI
- boards/LEGO_HUB_NO6: add board definition for LEGO_HUB_NO6
- Makefile: update to only pull in used Bluetooth library
- README.md: update supported MCUs, and submodule and mboot use
- usbd_desc: rename USBD_xxx descriptor opts to MICROPY_HW_USB_xxx
- usbd_cdc_interface: rename USBD_CDC_xx opts to MICROPY_HW_USB_xx
- powerctrl: support changing frequency on WB MCUs
- boards/NUCLEO_H743ZI2: add modified version of NUCLEO_H743ZI
- mbedtls: fix compile warning about uninitialized val
- enable MICROPY_PY_FSTRINGS by default
- add implementation of machine.bitstream
- Makefile: allow GIT_SUBMODULES and LIBS to be extended
- stm32_it: support TIM17 IRQs on WB MCUs
- disable computed goto on constrained boards
- storage: make extended-block-device more configurable
- boards/LEGO_HUB_NO6: change SPI flash storage to use hardware SPI
- boards/LEGO_HUB_NO6: skip first 1MiB of SPI flash for storage
- boards/LEGO_HUB_NO6: add make commands to backup/restore firmware
teensy port: no changes specific to this component/port
unix port:
- modffi: add option to lock GC in callback, and cfun access
- Makefile: add back LIB_SRC_C to list of object files
- variants: enable help and help("modules") on standard and dev
- Makefile: disable error compression on arm-linux-gnueabi-gcc
windows port:
- Makefile: add .exe extension to executables name
- appveyor: update to VS 2017 and use Python 3.8 for build/test
zephyr port:
- machine_spi: add support for hardware SPI
Optionally enabled via MICROPY_PY_UJSON_SEPARATORS. Enabled by default.
For dump, make sure mp_get_stream_raise is called after
mod_ujson_separators since CPython does it in this order (if both
separators and stream are invalid, separators will raise an exception
first).
Add separators argument in the docs as well.
Signed-off-by: Peter Züger <zueger.peter@icloud.com>
Signed-off-by: Damien George <damien@micropython.org>
This is a slight trade-off with code size, in places where a "_varg"
mp_raise variant is now used. The net savings on trinket_m0 is
just 32 bytes.
It also means that the translation will include the original English
text, and cannot be translated. These are usually names of Python
types such as int, set, or dict or special values such as "inf" or
"Nan".
These macros could in principle be (inline) functions so it makes sense to
have them lower case, to match the other C API functions.
The remaining macros that are upper case are:
- MP_OBJ_TO_PTR, MP_OBJ_FROM_PTR
- MP_OBJ_NEW_SMALL_INT, MP_OBJ_SMALL_INT_VALUE
- MP_OBJ_NEW_QSTR, MP_OBJ_QSTR_VALUE
- MP_OBJ_FUN_MAKE_SIG
- MP_DECLARE_CONST_xxx
- MP_DEFINE_CONST_xxx
These must remain macros because they are used when defining const data (at
least, MP_OBJ_NEW_SMALL_INT is so it makes sense to have
MP_OBJ_SMALL_INT_VALUE also a macro).
For those macros that have been made lower case, compatibility macros are
provided for the old names so that users do not need to change their code
immediately.
Introduction of ports subdirectory where all ports are moved to
The main change in this release is the introduction of a "ports/"
subdirectory at the top-level of the repository, and all of the ports are
moved here. In the process the "stmhal" port is renamed to "stm32" to
better reflect the MCU that it targets. In addition, the STM32 CMSIS and
HAL sources are moved to a new submodule called "stm32lib".
The bytecode has changed in this release, compared to the previous release,
and as a consequence the .mpy version number has increased to version 3.
This means that scripts compiled with the previous mpy-cross must be
recompiled to work with this new version.
There have also been various enhancements and optimisations, such as:
check for valid UTF-8 when creating str objects, support for reverse
special binary operations like __radd__, full domain checking in the math
module, support for floor-division and modulo in the viper emitter,
and addition of stack overflow checking when executing a regex.
The stm32 port sees improved support for F7 MCUs, addition of a new board
B_L475E_IOT01A based on the STM32L475, and support for the Wiznet W5500
chipset along with improved socket behaviour.
A detailed list of changes follows.
py core:
- objstr: startswith, endswith: check arg to be a string
- nlrx86,x64: replace #define of defined() with portable macro usage
- objtype: handle NotImplemented return from binary special methods
- objtype: mp_obj_class_lookup: improve debug logging
- map: remove unused new/free functions
- make m_malloc_fail() have void return type, since it doesn't return
- modstruct: in struct.pack, stop converting if there are no args left
- modstruct: check and prevent buffer-read overflow in struct unpacking
- modstruct: check and prevent buffer-write overflow in struct packing
- nlrthumb: get working again on standard Thumb arch (ie not Thumb2)
- objfloat: fix binary ops with incompatible objects
- obj: fix comparison of float/complex NaN with itself
- objtype: implement fallback for instance inplace special methods
- objtuple: properly implement comparison with incompatible types
- objstr: add check for valid UTF-8 when making a str from bytes
- objlist: properly implement comparison with incompatible types
- runtime0.h: move relational ops to the beginning of mp_binary_op_t
- runtime0.h: move MP_BINARY_OP_DIVMOD to the end of mp_binary_op_t
- objtype: make sure mp_binary_op_method_name has full size again
- runtime0.h: put inplace arith ops in front of normal operations
- builtinhelp: simplify code slightly by extracting object type
- runtime: implement dispatch for "reverse op" special methods
- nlrx86: fix building for Android/x86
- builtinhelp: change signature of help text var from pointer to array
- runtime.h: change empty mp_warning macro so var-args are non empty
- modbuiltins: implement abs() by dispatching to MP_UNARY_OP_ABS
- {objfloat,objcomplex}: optimise MP_UNARY_OP_ABS by reusing variables
- mpconfig.h: add note that using computed gotos in VM is not C99
- objstr: strip: don't strip "\0" by default
- objexcept: prevent infinite recursion when allocating exceptions
- stream: remove unnecessary checks for NULL return from vstr_add_len
- vstr: raise a RuntimeError if fixed vstr buffer overflows
- vm: use lowercase letter at start of exception message
- persistentcode: define mp_raw_code_save_file() for any unix target
- add config option to print warnings/errors to stderr
- objfloat: support raising a negative number to a fractional power
- objset: simplify set and frozenset by separating their locals dicts
- objset: check that RHS of a binary op is a set/frozenset
- objset: include the failed key in a KeyError raised from set.remove
- objtype: change type of enum-to-qstr table to uint16_t to save space
- objstr: make empty bytes object have a null-terminating byte
- mpprint: only check for null string printing when NDEBUG not defined
- objtype: clean up unary- and binary-op enum-to-qstr mapping tables
- persistentcode: bump .mpy version number to version 3
- bc: update opcode_format_table to match the bytecode
- modmath: add full checks for math domain errors
- modmath: convert log2 macro into a function
- formatfloat: don't print the negative sign of a NaN value
- formatfloat: use standard isinf, isnan funcs instead of custom ones
- modbuiltins: use existing utf8_get_char helper in builtin ord func
- emitnative: implement floor-division and modulo for viper emitter
- objtype: use CPython compatible method name for sizeof
- objtype: fit qstrs for special methods in byte type
- objtype: define all special methods if requested
- objtype: introduce MICROPY_PY_ALL_INPLACE_SPECIAL_METHODS
extmod:
- modubinascii: only include uzlib/tinf.h when it's really needed
- modussl_mbedtls: allow to compile with MBEDTLS_DEBUG_C disabled
- machine_pinbase: put PinBase singleton in ROM
- re1.5: upgrade to v0.8.2, adds hook for stack overflow checking
- modure: add stack overflow checking when executing a regex
- uos_dupterm: update uos.dupterm() and helper funcs to have index
- uos_dupterm: swallow any errors from dupterm closing the stream
- vfs: replace VLA in proxy func with small, static sized array
- modussl: add finaliser support for ussl objects
- modussl_mbedtls: allow to compile with unix coverage build
lib:
- add new submodule, stm32lib containing STM32 CMSIS and HAL source
- embed/abort_: use mp_raise_msg helper function
- libm: fix tanhf so that it correctly handles +/- infinity args
- libm: remove implementation of log2f, use MP_NEED_LOG2 instead
- axtls: update, support for SSL_EAGAIN return code
- berkeley-db-1.xx: update, allow to override MINCACHE, DEFPSIZE
drivers:
- memory/spiflash: change from hard-coded soft SPI to generic SPI
- display/ssd1306.py: improve performance of graphics methods
- nrf24l01: make nRF24L01 test script more portable
- display/ssd1306: implement SSD1306_I2C poweron method
- display/ssd1306: make poweron() work the same with SSD1306_SPI
- wiznet5k: improve the performance of socket ops with threading
- wiznet5k: get low-level W5500 driver working
tools:
- upip: upgrade to 1.2.2
- pyboard: use repr() when quoting data in error messages
- pyboard: update docstring for additional device support
tests:
- object_new: better messages, check user __new__() method
- class_new: add checks for __init__ being called and other improvements
- class_new: add another testcase for __new__/__init__ interaction
- class_inplace_op: test for inplace op fallback to normal one
- run-bench-tests: update locations of executables, now in ports/
- class_reverse_op: test for reverse arith ops special methods
- run-tests: skip class_inplace_op for minimal profile
- run-tests: fix copy-paste mistake in var name
- cpydiff: add cases for locals() discrepancies
- extmod: add test for ure regexes leading to infinite recursion
- extmod: add test for '-' in character class in regex
- run-tests: close device under test using "finally"
- net_inet: update tls test to work with CPython and incl new site
unix port:
- rename modsocket.c to modusocket.c
- modusocket: remove #if MICROPY_SOCKET_EXTRA code blocks
- enable MICROPY_PY_REVERSE_SPECIAL_METHODS
stm32 port:
- modmachine: make machine.bootloader() work when MPU is enabled
- modmachine: improve support for sleep/deepsleep on F7 MCUs
- compute PLL freq table during build instead of at run time
- modmachine: for F7 MCU, save power by reducing internal volt reg
- boards/pllvalues.py: make script work with both Python 2 and 3
- Makefile: use lib/stm32lib instead of local cmsis and hal files
- remove cmsis and hal files, they are now a submodule
- Makefile: automatically fetch stm32lib submodule if needed
- update to new STM Cube HAL library
- fix clock initialisation of L4 MCUs
- rename stmhal port directory to stm32
- remove unused usbd_msc.c file
- boards: change remaining stm32f4xx_hal_conf.h to unix line ending
- boards: change linker scripts to use "K" instead of hex byte size
- boards: fix I2C1 pin mapping on NUCLEO_F401RE/F411RE boards
- i2c: when scanning for I2C devices only do 1 probe per address
- modnwwiznet5k: release the GIL on blocking network operations
- boards: add new board B_L475E_IOT01A based on STM32L475
- make-stmconst.py: make sure mpz const data lives in ROM
- timer: make pyb.Timer() instances persistent
- mpconfigport.h: add configuration for max periphs on L4 series
- usbdev: make the USBD callback struct const so it can go in ROM
- usbdev: change static function variable to non-static
- usbdev: put all CDC state in a struct
- usbdev: put all HID state in a struct
- usbdev: simplify CDC tx/rx buffer passing
- usbdev: simplify HID tx/rx buffer passing
- usbdev/core: add state parameter to all callback functions
- usbdev: put all state for the USB device driver in a struct
- usbdev: simplify pointers to MSC state and block dev operations
- usbdev: merge all global USB device state into a single struct
- usbdev: make device descriptor callbacks take a state pointer
- usbdev: move all the USB device descriptor state into its struct
- timer: enable ARPE so that timer freq can be changed smoothly
- modnwwiznet5k: get the IP address of an established socket
- boards: fix typos in stm32f767_af.csv table
- usbd_cdc_interface: don't reset CDC output buf on initialisation
- modnwwiznet5k: implement WIZNET5K.isconnected() method
- modusocket: make getaddrinfo() work when passed an IP address
- modusocket: return OSError(-2) if getaddrinfo fails
- mpconfigport.h: add MICROPY_THREAD_YIELD() macro
- modnwwiznet5k: add support for W5500 Ethernet chip
- modnwwiznet5k: increase SPI bus speed to 42MHz
- modnwwiznet5k: implement stream ioctl for the Wiznet driver
- mphalport: improve efficiency of mp_hal_stdout_tx_strn_cooked
- make uos.dupterm() conform to specs by using extmod version
cc3200 port:
- enable micropython.kbd_intr() method
- use standard implementation of keyboard interrupt
esp8266 port:
- rename axtls_helpers.c to posix_helpers.c
- posix_helpers: set ENOMEM on memory alloc failure
- set DEFPSIZE=1024, MINCACHE=3 for "btree" module
- esp_mphal: send data in chunks to mp_uos_dupterm_tx_strn
- modnetwork: add "bssid" keyword arg to WLAN.connect() method
- modules/webrepl_setup: add info about allowed password length
zephyr port:
- Makefile: revamp "test" target after ports were moved to ports/
- use CONFIG_NET_APP_SETTINGS to setup initial network addresses
- switch to interrupt-driven pull-style console
pic16bit port:
- add definition of SEEK_SET to unistd.h
docs:
- pyboard/tutorial: add "timeout=0" to UART in pass-through example
- more xrefs to "MicroPython port" in glossary
- library/network: fix ref to "socket" module (should be "usocket")
- machine.Signal: improve style/grammar and add usage example
- library: add description of "index" parameter to uos.dupterm()
- library/micropython: fix typo in RST formatting
- library/framebuf.rst: generalise constructor to all colour formats
- btree: describe page caching policy of the underlying implementation
- esp8266/tutorial: update neopixel with example of using 4 bbp
- library/network: clarify usage of "bssid" arg in connect() method
- pyboard/quickref: add info for Switch, RTC, CAN, Accel classes
- pyboard/tutorial: update now that yellow LED also supports PWM
- esp8266/quickref: add quickref info for RTC class
- library: add missing cross-ref links for classes in pyb module
- library/network: update docs to state that W5500 is supported
- uselect: document one-shot polling mode
- usocket: elaborate descriptions
- usocket: document inet_ntop(), inet_pton()
- library/network: add dhcp_hostname parameter
- reference/isr_rules: minor typo correction
- ussl: fix module name refs and use "MicroPython port" term
- esp8266/general: add section on TLS limitations
- usocket: document that settimeout() isn't supported by all ports
- ure: add "|" (alternative) to the list of supported operators
- reference/isr_rules.rst: add tutorial on use of micropython.schedule()
travis:
- use --upgrade when pip is installing cpp-coveralls
- update build command now that stm32 Wiznet config has changed
examples:
- hwconfig_console: add .on()/.off() methods
all:
- convert mp_uint_t to mp_unary_op_t/mp_binary_op_t where appropriate
- convert remaining "mp_uint_t n_args" to "size_t n_args"
- make new ports/ sub-directory and move all ports there
- update Makefiles and others to build with new ports/ dir layout
- remove inclusion of internal py header files
- use NULL instead of "" when calling mp_raise exception helpers
README:
- update "Dependencies" section
- add explicit section on contributing
- add gcc and arm-none-eabi-newlib to list of required components
.gitattributes:
- remove obsolete entries for stmhal/hal, stmhal/cmsis
- add entries for files that will move to ports/ dir
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
The unary-op/binary-op enums are already defined, and there are no
arithmetic tricks used with these types, so it makes sense to use the
correct enum type for arguments that take these values. It also reduces
code size quite a bit for nan-boxing builds.
Dan Halbert
Jeff Epler
Jim Mussared
Scott Shawcroft
Timon
Peter Züger
Jeff Epler
microDev
Radomir Dopieralski
Diego Elio Pettenò
Damien George
Roy Hooper
Scott Shawcroft
Paul Sokolovsky