Instead of board pins, so that pins which have only the CPU specified in
pins.csv can still be used with mp_hal_pin_config_alt_static().
Signed-off-by: Damien George <damien@micropython.org>
A board can now define the following linker symbols to configure its flash
storage layout:
_micropy_hw_internal_flash_storage_start
_micropy_hw_internal_flash_storage_end
_micropy_hw_internal_flash_storage_ram_cache_start
_micropy_hw_internal_flash_storage_ram_cache_end
And optionally have a second flash segment by configuring
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE_SEGMENT2 to 1 and defining:
_micropy_hw_internal_flash_storage2_start
_micropy_hw_internal_flash_storage2_end
Signed-off-by: Damien George <damien@micropython.org>
This reduces code size and code duplication, and fixes `pyb.usb_mode()` so
that it now returns the correct string when in multi-VCP mode (before, it
would return None when in one of these modes).
Signed-off-by: Damien George <damien@micropython.org>
- update esp-idf to v4.4
- add esp32s3 support
- add analogio on esp32c3
- disable rgbmatrix on all espressif soc
Co-authored-by: Scott Shawcroft <scott@adafruit.com>
Co-authored-by: Seon Rozenblum <seon@unexpectedmaker.com>
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle. The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.
Extensions: support PWM for channel pairs. Channel pairs are declared by
supplying 2-element tuples for the pins. The two channels of a pair must
be the A/B channel of a FLEXPWM module. These form than a complementary
pair.
Additional supported keyword arguments:
- center=value Defines the center position of a pulse within the pulse
cycle. The align keyword is actually shortcut for center.
- sync=True|False: If set to True, the channels will be synchronized to a
submodule 0 channel, which has already to be enabled.
- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
channels are Center-Aligned or Edge-aligned. The channels must be either
complementary a channel pair or a group of synchronized channels. It may
as well be applied to a single channel, but withiout any benefit.
- invert= 0..3. Controls ouput inversion of the pins. Bit 0 controls the
first pin, bit 1 the second.
- deadtime=time_ns time of complementary channels for delaying the rising
slope.
- xor=0|1|2 xor causes the output of channel A and B to be xored. If
applied to a X channel, it shows the value oif A ^ B. If applied to an A
or B channel, both channel show the xored signal for xor=1. For xor=2,
the xored signal is split between channels A and B. See also the
Reference Manual, chapter about double pulses. The behavior of xor=2 can
also be achieved using the center method for locating a pulse within a
clock period.
The output is enabled for board pins only.
CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output. That applies only to FLEXPWM pins. The
use of QTMR pins which are not board pins will be rejected.
As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
This is to make the builds for all nucleo/discovery boards uniform, so they
can be treated the same by the auto build scripts.
The CI script is updated to explicitly enable mboot and packing, to test
these features.
Signed-off-by: Damien George <damien@micropython.org>
This prevents SPI4/5 from being used if SDIO and CYW43 are enabled, because
the DMA for the SDIO is used on an IRQ and must be exclusivly available for
use by the SDIO peripheral.
Signed-off-by: Damien George <damien@micropython.org>
Because DMA2 may be in use by other peripherals, eg SPI1.
On PYBD-SF6 it's possible to trigger a bug in the existing code by turning
on WLAN and connecting to an AP, pinging the IP address from a PC and
running the following code on the PYBD:
def spi_test(s):
while 1:
s.write('test')
s.read(4)
spi_test(machine.SPI(1,100000000))
This will eventually fail with `OSError: [Errno 110] ETIMEDOUT` because
DMA2 was turned off by the CYW43 driver during the SPI1 transfer.
This commit fixes the bug by removing the code that explicitly disables
DMA2. Instead DMA2 will be automatically disabled after an inactivity
timeout, see commit a96afae90f6e5d693173382561d06e583b0b5fa5
Signed-off-by: Damien George <damien@micropython.org>
