Travis now limits the amount of free minutes for open-source projects, and
it does not provide enough for this project. So stop using it and instead
use on GitHub Actions.
Signed-off-by: Damien George <damien@micropython.org>
Also known as L2CAP "connection oriented channels". This provides a
socket-like data transfer mechanism for BLE.
Currently only implemented for NimBLE on STM32 / Unix.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
This fixes the build for non-STM32WB based boards when the NimBLE submodule
has not been fetched, and also allows STM32WB boards to build with BLE
disabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the STM32WB HCI interface (between the two CPUs) to
require the use of MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS, and as a
consequence to require NimBLE. IPCC RX IRQs now schedule the NimBLE
handler to run via mp_sched_schedule.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This test currently passes on Unix/PYBD, but fails on WB55 because it lacks
synchronisation of the internal flash.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead. This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.
The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms. When RX IRQ idle events arrive, it will also schedule this
task to improve latency.
There is a similar change for the unix port where the background thread now
queues the scheduled task.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This requires that the event handlers are called from non-interrupt context
(i.e. the MicroPython scheduler).
This will allow the BLE stack (e.g. NimBLE) to run from the scheduler
rather than an IRQ like PENDSV, and therefore be able to invoke Python
callbacks directly/synchronously. This allows writing Python BLE handlers
for events that require immediate response such as _IRQ_READ_REQUEST (which
was previous a hard IRQ) and future events relating to pairing/bonding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Using a semaphore (the previous approach) will only run the UART, whereas
for startup we need to also run the event queue.
This change makes it run the full scheduler hook.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of having the stack indicate a "start", "data"..., "end", pass
through the data in one callback as an array of chunks of data.
This is because the upcoming non-ringbuffer modbluetooth implementation
cannot buffer the data in the ringbuffer and requires instead a single
callback with all the data, to pass to the Python callback.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Use the same `wait_for_event` in all tests that doesn't hold a reference to
the event data tuple and handles repeat events.
Also fix a few misc reliability issues around timeouts and sequencing.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change machine.mem32['foo'] (or using any other non-integer
subscript) could result in a fault due to 'foo' being interpreted as an
integer. And when writing code it's hard to tell if the fault is due to a
bad subscript type, or an integer subscript that specifies an invalid
memory address.
The type of the object used in the subscript is now tested to be an
integer by using mp_obj_get_int_truncated instead of
mp_obj_int_get_truncated. The performance hit of this change is minimal,
and machine.memX objects are more for convenience than performance (there
are many other ways to read/write memory in a faster way),
Fixes issue #6588.
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
This gives a substantial speedup of the preprocessing step, i.e. the
generation of qstr.i.last. For example on a clean build, making
qstr.i.last:
21s -> 4s on STM32 (WB55)
8.9 -> 1.8s on Unix (dev).
Done in collaboration with @stinos.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.
Signed-off-by: Damien George <damien@micropython.org>
Add working example code to provide a starting point for users with files
that they can just copy, and include the modules in the coverage test to
verify the complete user C module build functionality. The cexample module
uses the code originally found in cmodules.rst, which has been updated to
reflect this and partially rewritten with more complete information.
Support building .cpp files and linking them into the micropython
executable in a way similar to how it is done for .c files. The main
incentive here is to enable user C modules to use C++ files (which are put
in SRC_MOD_CXX by py.mk) since the core itself does not utilize C++.
However, to verify build functionality a unix overage test is added. The
esp32 port already has CXXFLAGS so just add the user modules' flags to it.
For the unix port use a copy of the CFLAGS but strip the ones which are not
usable for C++.
