This change allows the same heap allocation rules to be used when using
malloc regardless if the board has SPRAM or normal RAM.
Integrating with the esp32-camera for example requires that ESP32 SPRAM be
allocatable using the esp-idf capabilities aware allocation functions. In
the case of esp32-camera it's for the framebuffer.
Detect when CONFIG_SPIRAM_USE_MALLOC is in use and use the standard
automatic configuration of leaving 1/2 of the SPRAM available to other
FreeRTOS tasks.
For example the ESP32-C3 has 2 TX channels and 2 RX channels in total, and
in this case channel 1 must be the default for bitstream.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE. This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
It's needed at least on F4 because this file overrides the weak function
HAL_RCC_DeInit() from hal_rcc.c.
Signed-off-by: Damien George <damien@micropython.org>
PLL3-Q is more reliable than PLL1-Q for the USB clock source when entering
mboot from various reset states (eg power on vs MCU reset). (It was found
that if the main application used PLL3-Q then sometimes the USB clock
source would stay stuck on PLL3-Q and not switch to PLL1-Q after a reset.)
Other related changes:
- SystemCoreClockUpdate() should be called on H7 because the calculation
can be involved in some cases.
- __set_PRIMASK(0) should be called because on H7 the built-in ST DFU
bootloader exits with IRQs disabled.
Signed-off-by: Damien George <damien@micropython.org>
H7 MCUs have ECC and writes do not go through to SRAM until 64-bits have
been written (on another location is written). So use 64-bit writes for
the bootloader-state variable so it is committed before the system reset.
As part of this change, the lower byte of the bootloader address in
BL_STATE must now be the magic number 0x5a5 for the state to be valid
(previously this was 0x000 which is not as robust).
Signed-off-by: Damien George <damien@micropython.org>
The original code used a independent state with regards to the interrupt.
During heavy bus error conditions the internal state could become
out-of-sync with the interrupts.
Further explanation: during the development of an application using CAN
communication, a interrupt-run-away was found in some situations. It was
found that the error interrupt triggered (Warning, Passive or Bus-Off, all
triggered it) the run-away. The only recovery was a reset.
Two problems were found:
- the error interrupt is enabled but not cleared in the interrupt routine;
- an internal variable 'State' that was used to track the message received
state (empty, new, full, overflow) that was not directly related to
interrupt that indicated the state.
In this commit these issues are fixed by adding more values for the
interrupt reason (warning, passive, bus off) and clearing the error
interrupts, and making the internal state directly dependent on the
interrupt state for received messages.
Furthermore, introducing the FIFO1 in the CAN receive stage, another issue
existed. Even if the messages are received into the FIFO1 (by selecting
message filtering for FIFO0 and FIFO1), the interrupt firing was indicating
FIFO0 Rx. The configuration of the interrupts for this is now also fixed.
The CAN peripheral has 2 interrupt lines going into the NVIC controller.
The assignment of the interrupt reasons to these 2 interrupt lines was
missing. Now the reception of FIFO1 messages triggers the second interrupt
line. Other interrupts (Rx FIFO0 and bus error) are assigned to the first
interrupt line.
Tested on a Nucleo-G474, and also checked the HAL function to work with the
H7 family.
The board.json file is intentionally excluded, until the board will be
sold. But including it into the mimxrt series make it easier to keep
the build up-to-date.
- Manufacturer, set by MICROPY_HW_USB_STR_MANUF; default "MicroPython"
- Board name, as set by MICROPY_HW_BOARD_NAME
- Unique-ID, same as returned by machine.unique_id()
- USB Vendor ID, as set by MICROPY_HW_USB_VID; default 0xf055
- USB Product ID, as set by MICROPY_HW_USB_PID; default 0x9802
Using the keyword argument cs=nnn in the constructor. The cs1
pin has to be defined in mpconfigboard.h.
Note: Only a few boards have the CS1 pin exposed to the connectors.
The Pin config setting by IOMUXC_SetPinConfig() is supplied by a
bit pattern. That pattern is specific for a MCU family. In preparation
for supporting the MIMXRT117x family, the constant bit pattern is
replaced by a function call, such that the bit pattern is created
at a single place. The code for this functions was taken from
machine_pin.c.
Note: A working port for the MIMXRT1176 exists already.
This library file has a bug, in that TransferBlocking returns before the
transfer has finished. That is a problem if a write follows immediately
a read.
If in a board's mkconfigboard.mk the following symbol is set:
MICROPY_HW_BOARD_FLASH_FILES = 1
then the files:
($BOARD)_flexspi_flash_config.h and
qspi_nor_flash_config.c and/or
qspi_hyper_flash_config.c
are expected in the board directory. Otherwise the common files from
the hal directory are used.
The keyword "af" has been deprecated for some time and "alt" should be used
instead (but "af" still works).
Signed-off-by: Damien George <damien@micropython.org>
This allows encoding things (eg a Basic-Auth header for a request) without
slicing the \n from the string, which allocates additional memory.
Co-authored-by: David Lechner <david@lechnology.com>
Damien George
Emil Kondayan
Michael O'Cleirigh
IhorNehrutsa
Herwin Grobben
iabdalkader
robert-hh
Andrew Leech
Christian Decker
stijn
Jos Verlinde
ubi de feo
marcidy
Sean Coates