Add a field to allow specifying a timeout when initiating advertising.
As part of this, add a new property to determine if the device is still
advertising.
Additionally, have the `anonymous` property require a timeout, and set
the timeout to the maximum possible value if no timeout is specified.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a new parameter to the `start_advertising()` function to enable
anonymous advertising. This forces a call to `sd_ble_gap_privacy_set()`
with `privacy_mode` set to `BLE_GAP_PRIVACY_MODE_DEVICE_PRIVACY` and
`private_addr_type` set to
`BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE`.
With this, addresses will cycle at a predefined rate (currently once
every 15 minutes).
Signed-off-by: Sean Cross <sean@xobs.io>
This change takes polygon from 126k pixels per second fill to 240k pps fill
on a reference 5 point star 50x66px polygon, updating both location and shape
at 10hz. Tested on an m4 express feather.
As a curiosity, the flat-out fill rate of a shape whose get_pixel is `return 0;`
fills just shy of 375k pixels per second.
When calling `AES.decrypt_into()` or `AES.encrypt_into()`, the
destination buffers may be any buffer kind. However, we currently
aren't checking to make sure the destination buffer is actually
writable.
Specify `MP_BUFFER_WRITE` for the destination buffers of both of these
objects so we don't inadvertently write to immutable data.
Signed-off-by: Sean Cross <sean@xobs.io>
In order to accept both `bytes` objects and `bytearray` objects, use a
`bufinfo` construct to retrieve the data rather than
`mp_obj_str_get_data()`.
Signed-off-by: Sean Cross <sean@xobs.io>
Ujson should only worry about whitespace before JSON. This becomes apparent when you are using MP stream protocol to read directly from input buffers.
When you attempt to read(1) on a UART (and possibly other protocols) you have to wait for either the byte or the timeout.
Fixes:
- Waiting for a timeout after you have completed reading a correct and complete JSON off the input.
- Raising an OSError after reading a correct and complete JSON off the input.
- Eating more data than semantically owned off the input buffer.
- Blocking to start parsing JSON until the entire JSON body has been loaded into a potentially large, contiguous Python object.
Code you would write before:
```
line = board_busio_uart_port.read_line()
json_dict = json.loads(line)
```
or reaching for fixed buffers and swapping them around in Python.
Code that did not work before that does now:
```
json_dict = json.load(board_busio_uart_port)
```
- This removes the need for intermediate copies of data when reading JSON from micropython stream protocol inputs.
- It also increases total application speed by parsing JSON concurrently with receiving on boards that read from UART via DMA.
- It simplifies code that users write while improving their apps.
vectorio builds on m4 express feather
Concrete shapes are composed into a VectorShape which is put into a displayio Group for display.
VectorShape provides transpose and x/y positioning for shape implementations.
Included Shapes:
* Circle
- A radius; Circle is positioned at its axis in the VectorShape.
- You can freely modify the radius to grow and shrink the circle in-place.
* Polygon
- An ordered list of points.
- Beteween each successive point an edge is inferred. A final edge closing the shape is inferred between the last
point and the first point.
- You can modify the points in a Polygon. The points' coordinate system is relative to (0, 0) so if you'd like a
top-center justified 10x20 rectangle you can do points [(-5, 0), (5, 0), (5, 20), (0, 20)] and your VectorShape
x and y properties will position the rectangle relative to its top center point
* Rectangle
A width and a height.
Fix for Issue #2812. Instead of reporting a missing attribute for functions such as time.time() and time.mktime(); platforms that do not have long integer support will raise a NotImplementedError
This adds initial support for an AES module named aesio. This
implementation supports only a subset of AES modes, namely
ECB, CBC, and CTR modes.
Example usage:
```
>>> import aesio
>>>
>>> key = b'Sixteen byte key'
>>> cipher = aesio.AES(key, aesio.MODE_ECB)
>>> output = bytearray(16)
>>> cipher.encrypt_into(b'Circuit Python!!', output)
>>> output
bytearray(b'E\x14\x85\x18\x9a\x9c\r\x95>\xa7kV\xa2`\x8b\n')
>>>
```
This key is 16-bytes, so it uses AES128. If your key is 24- or 32-
bytes long, it will switch to AES192 or AES256 respectively.
This has been tested with many of the official NIST test vectors,
such as those used in `pycryptodome` at
39626a5b01/lib/Crypto/SelfTest/Cipher/test_vectors/AES
CTR has not been tested as NIST does not provide test vectors for it.
Signed-off-by: Sean Cross <sean@xobs.io>
When allocate_display_bus_or_raise was factored out, the assignment
of the bus's Python type was lost. Restore it.
This would have affected displays of any type other than RGBMatrix, when
they were created dynamically. Boards with displays configured in flash
were unaffected.
Closes: #2792
This gets all the purely internal references. Some uses of
protomatter/Protomatter/PROTOMATTER remain, as they are references
to symbols in the Protomatter C library itself.
I originally believed that there would be a wrapper library around it,
like with _pixelbuf; but this proves not to be the case, as there's
too little for the library to do.
Surely readline() "rtype" is string not int as stated (and not bytes as some might expect).
Also it is not totally unambiguous what happens on a timeout so it would help to clarify in docs that on a timeout
it does NOT return with what it has read so far, rather it leaves all that in the buffer ready for a future read and returns nothing.
Likewise clarify that if timeout=0 but there is no newline it DOES return what it has read so far (NOT None).
At least this is what I think it does and/or is supposed to do!
Python docs are generally not too explicit about what is the proper treatment, so perhaps all the more reason to
clarify the interpretation adopted?
They're not readily distinguishable by type.
I also added the requested height optional parameter; this is checked
against the computed one. It's not feasible to use this parameter to
artificailly reduce the number of used rows, because changes in the
underlying C protomatter library would be required.
Finally, I added a better error message when the number of RGB pins was
not what was expected.
It was fixed as 0/0 even though it used to get it from the current
SPI state. This makes it more explicit with kwargs.
Thanks to magpie_lark and kmatocha on the Adafruit Support forum
for finding the issue: https://forums.adafruit.com/viewtopic.php?f=60&t=162515
PacketBuffer facilitates packet oriented BLE protocols such as BLE
MIDI and the Apple Media Service.
This also adds PHY, MTU and connection event extension negotiation
to speed up data transfer when possible.
