Commit Graph

13 Commits

Author SHA1 Message Date
Mike Causer 47b778332a all: Replace busses with buses.
"buses" is the widely accepted plural form of "bus".
2021-05-20 23:22:03 +10:00
Andrew Leech ff9a61b5a8 stm32/sdram: Expose the result of sdram startup test in stm32_main.
This means boards can choose to only use it for gc heap if the test passes.
2020-02-04 18:18:41 +11:00
Damien George 009b1f6559 stm32/boards: Rework all stm32??xx_hal_conf.h files to use common code.
This eliminates a lot of duplicated code in these header files.
2019-06-25 14:18:24 +10:00
roland 10bddc5c28 stm32/boards/STM32F429DISC: Enable UART as secondary REPL.
The board(s) feature a VCOM through the ST-LINK, this feature is something
to keep around.
2018-12-01 17:30:48 +11:00
Andrew Leech 338635ccc6 stm32/main: Add configuration macros for board to set heap start/end.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).

As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot.  On boards with SDRAM enabled the heap
has been set to use that.
2018-10-05 17:30:18 +10:00
forester3 502c410214 stm32/boards/STM32F429DISC: Add burst len and autorefresh to SDRAM cfg.
To align with recent changes to sdram.c.
2018-08-14 16:03:13 +10:00
Andrew Leech 434975defa stm32/boards/STM32F429DISC: Enable onboard SDRAM. 2018-07-23 23:16:32 +10:00
Damien George a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George ed75b2655f stm32/Makefile: Allow a board to config either 1 or 2 firmware sections.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces.  Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
2018-03-27 21:24:15 +11:00
Damien George 7aec06ca9a stm32/boards: Allow boards to have finer control over the linker script.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory.  Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data.  This leaves room for storage (filesystem data) to live
between the firmware sections.

The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section.  Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
2018-03-27 21:17:48 +11:00
Damien George 34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George 02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00
Damien George 01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00