This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
Changes are:
- Fix missing IRQ handler when SDMMC2 is used instead of SDMMC1 with H7
MCUs.
- Removed outdated H7 series compatibility macros.
- Defined common IRQ handler macro for F4 series.
Some SD/MMC breakout boards don't support 4-bit bus mode. This adds a new
macro MICROPY_HW_SDMMC_BUS_WIDTH that allows each board to define the width
of the SD/MMC bus interface used on that board, defaulting to 4 bits.
With clock bypass enabled the attached SD card is clocked at the maximum
48MHz. But some SD cards are unreliable at these rates. Although it's
nice to have high speed transfers it's more important that the transfers
are reliable for all cards. So disable this clock bypass option.
The HAL DMA functions enable SDMMC interrupts before fully resetting the
peripheral, and this can lead to a DTIMEOUT IRQ during the initialisation
of the DMA transfer, which then clears out the DMA state and leads to the
read/write not working at all. The DTIMEOUT is there from previous SDMMC
DMA transfers, even those that succeeded, and is of duration ~180 seconds,
which is 0xffffffff / 24MHz (default DTIMER value, and clock of
peripheral).
To work around this issue, fully reset the SDMMC peripheral before calling
the HAL SD DMA functions.
Fixes issue #4110.
With this and previous patches the stm32 port can now be compiled using
object representation D (nan boxing). Note that native code and frozen mpy
files with float constants are currently not supported with this object
representation.
For a given IRQn (eg UART) there's no need to carry around both a PRI and
SUBPRI value (eg IRQ_PRI_UART, IRQ_SUBPRI_UART). Instead, the IRQ_PRI_UART
value has been changed in this patch to be the encoded hardware value,
using NVIC_EncodePriority. This way the NVIC_SetPriority function can be
used directly, instead of going through HAL_NVIC_SetPriority which must do
extra processing to encode the PRI+SUBPRI.
For a priority grouping of 4 (4 bits for preempt priority, 0 bits for the
sub-priority), which is used in the stm32 port, the IRQ_PRI_xxx constants
remain unchanged in their value.
This patch also "fixes" the use of raise_irq_pri() which should be passed
the encoded value (but as mentioned above the unencoded value is the same
as the encoded value for priority grouping 4, so there was no bug from this
error).
Rather than pin objects themselves. The actual object is now pin_X_obj and
defines are provided so that pin_X is &pin_X_obj. This makes it so that
code that uses pin objects doesn't need to know if they are literals or
objects (that need pointers taken) or something else. They are just
entities that can be passed to the map_hal_pin_xxx functions. This mirrors
how the core handles constant objects (eg mp_const_none which is
&mp_const_none_obj) and allows for the possibility of different
implementations of the pin layer.
For example, prior to this patch there was the following:
extern const pin_obj_t pin_A0;
#define pyb_pin_X1 pin_A0
...
mp_hal_pin_high(&pin_A0);
and now there is:
extern const pin_obj_t pin_A0_obj;
#define pin_A0 (&pin_A0_obj)
#define pyb_pin_X1 pin_A0
...
mp_hal_pin_high(pin_A0);
This patch should have minimal effect on board configuration files. The
only change that may be needed is if a board has .c files that configure
pins.
genhdr/pins.h is an internal header file that defines all of the pin
objects and it's cleaner to have pin.h include it (where the struct's for
these objects are defined) rather than an explicit include by every user.
The CMSIS files for the STM32 range provide macros to distinguish between
the different MCU series: STM32F4, STM32F7, STM32H7, STM32L4, etc. Prefer
to use these instead of custom ones.
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
Damien George
iabdalkader
Jim Mussared
Damien George
Andrey Belykh
Chris Wilson
Andrew Leech
Peter D. Gray