Any external user of DMA (eg a board with a custom DMA driver) must call
dma_external_acquire() for their DMA controller/stream to ensure that the
DMA clock is not automatically turned off while it's still being used
externally.
Signed-off-by: Damien George <damien@micropython.org>
This change allows a CPU pin to be hidden from the user by prefixing it
with a "-" in the pins.csv file for a board. It will still be available in
C code, just not exposed to Python.
Signed-off-by: Damien George <damien@micropython.org>
Don't want users to accidentally use boot.py (because recovering requires
knowing how to activate safe mode).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit is based upon prior work of @dpgeorge and @koendv.
MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)
Support has been added for the STM32H7B3I_DK board.
Signed-off-by: Jan Staal <info@janstaal.com>
To simplify the socket state.
The CC3K driver (see drivers/cc3000/inc/socket.h and src/socket.c) has
socket() returning an INT16 so there is now enough room to store it
directly in the fileno member.
The zephyr port doesn't support SoftI2C so it's not enabled, and the legacy
I2C constructor check can be removed.
Signed-off-by: Damien George <damien@micropython.org>
To keep things neat and tidy, we ensure that each file has 1 and only 1
newline at the end of each file.
Signed-off-by: David Lechner <david@pybricks.com>
A board can now define the following to fully customise the extended block
device interface provided by the storage sub-system:
- MICROPY_HW_BDEV_BLOCKSIZE_EXT
- MICROPY_HW_BDEV_READBLOCKS_EXT
- MICROPY_HW_BDEV_WRITEBLOCKS_EXT
- MICROPY_HW_BDEV_ERASEBLOCKS_EXT
Signed-off-by: Damien George <damien@micropython.org>
This commit creates a new stm32 board for the NUCLEO_H743ZI2, which is the
current version of this from ST. This is a modified copy of the
NUCLEO_H743ZI board, and the ZI2 board differs in a few minor ways:
- LED2 has moved from PB7 to PE1 and is now yellow rather than blue
- the USB power enable has moved from PG6 to PG10
- the USER button is now pulled down
This allows changing the frequency to: 100kHz, 200kHz, 400kHz, 800kHz,
1MHz, 2MHz, 4MHz, 8MHz, 16MHz, 32MHz, 64MHz. For frequencies 2MHz and
below, low power run (LPR) mode is enabled automatically.
Signed-off-by: Damien George <damien@micropython.org>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
Call MICROPY_EVENT_POLL_HOOK even on very short delays so that busy loops
that call sleep_ms still yield to events and other threads.
See related issue #5344.
Replace "master" with "controller" and "slave" with "peripheral" in
comments, errors, and debug messages.
Add CONTROLLER and PERIPHERAL constants to pyb.SPI and pyb.I2C classes;
retain MASTER and SLAVE constants for backward compatiblity.
