This makes it possible for cooperative multitasking systems to keep running
event loops during garbage collector operations.
For example, this can be used to ensure that a motor control loop runs
approximately each 5 ms. Without this hook, the loop time can jump to
about 15 ms.
Addresses #3475.
Signed-off-by: Laurens Valk <laurens@pybricks.com>
This is an stm32-specific feature that's accessed via the pyb module, so
not something that will be widely enabled.
Signed-off-by: Damien George <damien@micropython.org>
This commit is a no-op change. Future improvements can come from making
individual boards use CORE or BASIC.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Some of these will later be moved to CORE or BASIC, but EXTRA is a good
starting point based on what stm32 uses.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prior to this commit IRQs on STM32F4 could be lost because SR is cleared by
reading SR then reading DR. For example, if both RXNE and IDLE IRQs were
active upon entry to the IRQ handler, then IDLE is lost because the code
that handles RXNE comes first and accidentally clears SR (by reading SR
then DR to get the incoming character).
This commit fixes this problem by making the IRQ handler more atomic in the
following operations:
- get current IRQ status flags
- deal with RX character
- clear remaining status flags
- call user handler
On the STM32F4 it's very hard to get this right because the only way to
clear IRQ status flags is to read SR then DR, but the read of DR may read
some data which should remain in the register until the user wants to read
it. And it won't work to cache the read because RTS/CTS flow control will
then not work. So instead the new code disables interrupts if the DR is
full and waits for the user to read it before reenabling the interrupts.
Fixes issue mentioned in #4599 and #6082.
Signed-off-by: Damien George <damien@micropython.org>
Following on from ba940250a5, the change here
makes output about 15 times faster (now up to about 550 kbytes/sec).
tinyusb_cdcacm_write_queue will return the number of bytes written, so
there's no need to use tud_cdc_n_write_available.
Signed-off-by: Damien George <damien@micropython.org>
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.
Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
We're using the MicroPython fork of NimBLE, which on the
`micropython_1_4_0` branch re-adds support for 64-bit targets and fixes
initialisation of g_msys_pool_list.
Also updates modbluetooth_nimble.c to suit v1.4.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
There is no release of IDF v4.4 yet but master is now on v5.0-dev so a
specific commit must be chosen to stick to v4.4.
Signed-off-by: Damien George <damien@micropython.org>
By moving code to ITCM, like vm, gc, parse, runtime. The change affects
mostly the execution speed of MicroPython code. The speed is increased by
up to a factor of 6, especially for MCU with small cache.
Prior to this commit mp_hal_ticks_cpu() was not started properly. It only
started when the code was executed with a debugger attached, except for the
Teensy (i.MXRT1062) boards. As an additional fix, the CYYCNT timer is now
started at boot time.
Also rename mp_hal_ticks_cpu_init() to mp_hal_ticks_cpu_enable().
The API follows that of rp2, stm32, esp32, and the docs.
wdt=machine.WDT(0, timeout)
Timeout is given in ms. The valid range is 500 to 128000 (128
seconds) with 500 ms granularity. Values outside of that range will
be silently aligned.
wdt.feed()
Resets the watchdog timer (feeding).
wdt.timeout_ms(value)
Sets a new timeout and feeds the watchdog.
This is a new, preliminary method which is not yet documented.
reset_cause = machine.reset_cause()
Values returned:
1 Power On reset
3 Watchdog reset
5 Software reset: state after calling machine.reset()
More elaborate API functions are supported by the MCU, like an interrupt
called a certain time after feeding. But for port cosistency that is not
implemented.
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.
The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0
The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1
Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.
Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works
The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.
Some boards do not wire the RESET and INT pin of the PHY transceiver. For
operation, these are not required. If they are defined, they will be used.
Adds support for SDRAM via `SEMC` peripheral. SDRAM support can be
enabled in the mpconfigboard.mk file by setting `MICROPY_HW_SDRAM_AVAIL`
to `1` and poviding the size of the RAM via `MICROPY_HW_FLASH_SIZE`.
When SDRAM support is enabled the whole SDRAM is currently used used
for MicroPython heap.
Signed-off-by: Philipp Ebensberger
