For STM32G4 series, the internal sensors are connected to:
- ADC1_IN16: Temperature sensor
- ADC1_IN17: Battery voltage monitoring
- ADC1_IN18: Internal voltage reference
but ADC_CHANNEL_TEMPSENSOR_ADC1, ADC_CHANNEL_VBAT,
ADC_CHANNEL_VREFINT are not defined as 16, 17, 18.
This commit converts channel 16, 17, 18 to ADC_CHANNEL_x in
adc_get_internal_channel().
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STM32G4,
* TS_CAL1 raw data acquired at a temperature of 30°C
* TS_CAL2 raw data acquired at a temperature of 130°C
Also, these values are at VDDA=3.0V.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STM32G4, ADC clock frequency should be equal or less than 60MHz.
To satisfy this specification, ADC clock prescaler should be equal or
greater than 4 (For example, NUCLEO_G474RE runs 170MHz).
In addition, to obtain accurate internal channel value,
the ADC clock prescaler is set to 16 because vbat needs at least 12us
(16/170*247.5=23.3us).
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
For STMG4 MCUs, the peripheral registers for DAC have to be accessed by
words (32bits) because DAC is connected to AHB directly.
(This requirement is also there for other MCU series. However, if DAC is
connected to APB like F4/L1/L4 MCUs, AHB byte or half-word transfer is
changed into a 32-bit APB transfer. This means that PSIZE does not have to
be DMA_PDATAALIGN_WORD on these MCUs, and in fact must be BYTE/HALFWORD to
function correctly.)
Fixes issue #9563.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
To match the other functions in the machine module, in particular so that
MICROPY_PY_MACHINE can be disabled without getting a compiler warning about
unused code.
Signed-off-by: Damien George <damien@micropython.org>
Mostly updates comments, but also renames the UASYNCIO enum value to
ASYNCIO.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds initial support for STM32H5xx MCUs. The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot
Signed-off-by: Damien George <damien@micropython.org>
The G0 USB peripheral behaves more like MICROPY_HW_USB_IS_MULTI_OTG=0 than
that config =1. This fixes the configuration of the PMA FIFO buffers.
Signed-off-by: Damien George <damien@micropython.org>
For debugging purposes, to see output from other peripherals.
Also reset the pyb_stdio_uart state at the end of soft reset, in case it
points to a heap-allocated object.
Signed-off-by: Damien George <damien@micropython.org>
Following how mkrules.cmake works. This makes it easy for a port to enable
frozen code, by defining FROZEN_MANIFEST in its Makefile.
Signed-off-by: Damien George <damien@micropython.org>
This is a MicroPython-specific module that existed to support the old
version of uasyncio. It's undocumented and not enabled on all ports and
takes up code size unnecessarily.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Applies to drivers/examples/extmod/port-modules/tools.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates any includes, and references from Makefiles/CMake.
This essentially reverts what was done long ago in commit
136b5cbd76
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This renames the builtin-modules, such that help('modules') and printing
the module object will show "module" rather than "umodule".
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates all `help()` output to use the phrase:
`For online docs please visit http://docs.micropython.org/`
Some ports previously used different wording, some pointed to the wrong
link. Also make all ports use `help.c` for consistency.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Also fix MAX_ENDPOINT definition for G0, which follows G4.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Once all the firmware has been flashed and the final signatures checked,
mboot writes the "all good" byte into the header of the application. This
step uses the buffer firmware_head which, if unaligned in the build, fails
when cast to a uint64_t* in flash.c.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
These were incorrectly added in d995c01042.
The fix here includes the full differential ADC definitions.
Signed-off-by: brave ulysses <brave_ulysses@email.com>
This fixes:
- type-comparison (E721): do not compare types, use isinstance().
- string-dot-format-missing-arguments (F524): .format call is missing
argument(s) for placeholder(s): {message}.
- f-string-missing-placeholders (F541).
- is-literal (F632): Use != to compare constant literals.
The last one is fixed by just comparing for truthfulness of `state`.
Based on extmod/utime_mphal.c, with:
- a globals dict added
- time.localtime wrapper added
- time.time wrapper added
- time.time_ns function added
New configuration options are added for this module:
- MICROPY_PY_UTIME (enabled at basic features level)
- MICROPY_PY_UTIME_GMTIME_LOCALTIME_MKTIME
- MICROPY_PY_UTIME_TIME_TIME_NS
Signed-off-by: Damien George <damien@micropython.org>
