The SPI sub-system is independent from the uPy state (eg the heap) and so
can safely persist across a soft reset. And this is actually necessary for
drivers that rely on SPI and that also need to persist across soft reset
(eg external SPI flash memory).
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode. To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY. High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.
This patch has been tested on an STM32F733.
By defining MICROPY_HW_USB_MAIN_DEV a given board can select to use either
USB_PHY_FS_ID or USB_PHY_HS_ID as the main USBD peripheral, on which the
REPL will appear. If not defined this will be automatically configured.
There's no need to have these as separate functions, they just take up
unnecessary code space and combining them allows to factor common code, and
also allows to support arbitrary string descriptor indices.
The routine waits for the DMA to finish, which is signalled from a DMA IRQ
handler. Using WFI makes the CPU sleep while waiting for the IRQ to arrive
which decreases power consumption. To make it work correctly the check for
the change in state must be atomic and so IRQs must be disabled during the
check. The key feature of the Cortex MCU that makes this possible is that
WFI will exit when an IRQ arrives even if IRQs are disabled.
CPython doesn't allow SEEK_CUR with non-zero offset for files in text mode,
and uPy inherited this behaviour for both text and binary files. It makes
sense to provide full support for SEEK_CUR of binary-mode files in uPy, and
to do this in a minimal way means also allowing to use SEEK_CUR with
non-zero offsets on text-mode files. That seems to be a fair compromise.
Build and test 32bit and 64bit versions of the windows port using gcc
from mingw-w64. Note a bunch of tests which rely on floating point
math/printing have been disabled for now since they fail.
This commit fixes two things:
1. Do not allocate on the heap in readblocks() - unless the block size
is bigger than 512 bytes.
2. Raise an error instead of returning 1 to indicate an error: the FAT
block device layer does not check the return value. And other
backends (e.g. esp32 blockdev) also raise an error instead of
returning non-zero.
The number of registers used should be 10, not 12, to match the assembly
code in nlrx64.c. With this change the 64bit mingw builds don't need to
use the setjmp implementation, and this fixes miscellaneous crashes and
assertion failures as reported in #1751 for instance.
To avoid mistakes in the future where something gcc-related for Windows
only gets fixed for one particular compiler/environment combination,
make use of a MICROPY_NLR_OS_WINDOWS macro.
To make sure everything nlr-related is now ok when built with gcc this
has been verified with:
- unix port built with gcc on Cygwin (i686-pc-cygwin-gcc and
x86_64-pc-cygwin-gcc, version 6.4.0)
- windows port built with mingw-w64's gcc from Cygwin
(i686-w64-mingw32-gcc and x86_64-w64-mingw32-gcc, version 6.4.0)
and MSYS2 (like the ones on Cygwin but version 7.2.0)
Add some features which are already enabled in the unix port and
default to using the Python stack for scoped allocations: this can be
more performant in cases the heap is heavily used because for example
the memory needed for storing *args and **kwargs doesn't require
scanning the heap to find a free block.
For MSVC off_t is defined in sys/types.h but according to the comment
earlier in mpconfigport.h this cannot be included directly.
So just make off_t the same as mp_off_t.
This fixes the build for MSVC with MICROPY_STREAMS_POSIX_API
enabled because stream.h uses off_t.
There are two checks that are always false so can be converted to (negated)
assertions to save code space and execution time. They are:
1. The check of the str parameter, which is required to be non-NULL as per
the original comment that it has enough space in it as calculated by
mp_int_format_size. And for all uses of this function str is indeed
non-NULL.
2. The check of the base parameter, which is already required to be between
2 and 16 (inclusive) via the assertion in mp_int_format_size.
The motivation behind this patch is to remove unreachable code in mpn_div.
This unreachable code was added some time ago in
9a21d2e070, when a loop in mpn_div was copied
and adjusted to work when mpz_dig_t was exactly half of the size of
mpz_dbl_dig_t (a common case). The loop was copied correctly but it wasn't
noticed at the time that the final part of the calculation of num-quo*den
could be optimised, and hence unreachable code was left for a case that
never occurred.
The observation for the optimisation is that the initial value of quo in
mpn_div is either exact or too large (never too small), and therefore the
subtraction of quo*den from num may subtract exactly enough or too much
(but never too little). Using this observation the part of the algorithm
that handles the borrow value can be simplified, and most importantly this
eliminates the unreachable code.
The new code has been tested with DIG_SIZE=3 and DIG_SIZE=4 by dividing all
possible combinations of non-negative integers with between 0 and 3
(inclusive) mpz digits.
Empty __VA_ARGS__ are not allowed in the C preprocessor so adjust the rule
arg offset calculation to not use them. Also, some compilers (eg MSVC)
require an extra layer of macro expansion.
This is the sixth and final patch in a series of patches to the parser that
aims to reduce code size by compressing the data corresponding to the rules
of the grammar.
Prior to this set of patches the rules were stored as rule_t structs with
rule_id, act and arg members. And then there was a big table of pointers
which allowed to lookup the address of a rule_t struct given the id of that
rule.
The changes that have been made are:
- Breaking up of the rule_t struct into individual components, with each
component in a separate array.
- Removal of the rule_id part of the struct because it's not needed.
- Put all the rule arg data in a big array.
- Change the table of pointers to rules to a table of offsets within the
array of rule arg data.
The last point is what is done in this patch here and brings about the
biggest decreases in code size, because an array of pointers is now an
array of bytes.
Code size changes for the six patches combined is:
bare-arm: -644
minimal x86: -1856
unix x64: -5408
unix nanbox: -2080
stm32: -720
esp8266: -812
cc3200: -712
For the change in parser performance: it was measured on pyboard that these
six patches combined gave an increase in script parse time of about 0.4%.
This is due to the slightly more complicated way of looking up the data for
a rule (since the 9th bit of the offset into the rule arg data table is
calculated with an if statement). This is an acceptable increase in parse
time considering that parsing is only done once per script (if compiled on
the target).
Instead of each rule being stored in ROM as a struct with rule_id, act and
arg, the act and arg parts are now in separate arrays and the rule_id part
is removed because it's not needed. This reduces code size, by roughly one
byte per grammar rule, around 150 bytes.
The rule name is only used for debugging, and this patch makes things a bit
cleaner by completely separating out the rule name from the rest of the
rule data.
Each NLR implementation (Thumb, x86, x64, xtensa, setjmp) duplicates a lot
of the NLR code, specifically that dealing with pushing and popping the NLR
pointer to maintain the linked-list of NLR buffers. This patch factors all
of that code out of the specific implementations into generic functions in
nlr.c, along with a helper macro in nlr.h. This eliminates duplicated
code.
If MICROPY_NLR_SETJMP is not enabled and the machine is auto-detected then
nlr.h now defines some convenience macros for the individual NLR
implementations to use (eg MICROPY_NLR_THUMB). This keeps nlr.h and the
implementation in sync, and also makes the nlr_buf_t struct easier to read.
A function with a naked attribute must only contain basic inline asm
statements and no C code.
For nlr_push this means removing the "return 0" statement. But for some
gcc versions this induces a compiler warning so the __builtin_unreachable()
line needs to be added.
For nlr_jump, this function contains a combination of C code and inline asm
so cannot be naked.
This reverts commit 6a3a742a6c.
The above commit has number of faults starting from the motivation down
to the actual implementation.
1. Faulty implementation.
The original code contained functions like:
NORETURN void nlr_jump(void *val) {
nlr_buf_t **top_ptr = &MP_STATE_THREAD(nlr_top);
nlr_buf_t *top = *top_ptr;
...
__asm volatile (
"mov %0, %%edx \n" // %edx points to nlr_buf
"mov 28(%%edx), %%esi \n" // load saved %esi
"mov 24(%%edx), %%edi \n" // load saved %edi
"mov 20(%%edx), %%ebx \n" // load saved %ebx
"mov 16(%%edx), %%esp \n" // load saved %esp
"mov 12(%%edx), %%ebp \n" // load saved %ebp
"mov 8(%%edx), %%eax \n" // load saved %eip
"mov %%eax, (%%esp) \n" // store saved %eip to stack
"xor %%eax, %%eax \n" // clear return register
"inc %%al \n" // increase to make 1, non-local return
"ret \n" // return
: // output operands
: "r"(top) // input operands
: // clobbered registers
);
}
Which clearly stated that C-level variable should be a parameter of the
assembly, whcih then moved it into correct register.
Whereas now it's:
NORETURN void nlr_jump_tail(nlr_buf_t *top) {
(void)top;
__asm volatile (
"mov 28(%edx), %esi \n" // load saved %esi
"mov 24(%edx), %edi \n" // load saved %edi
"mov 20(%edx), %ebx \n" // load saved %ebx
"mov 16(%edx), %esp \n" // load saved %esp
"mov 12(%edx), %ebp \n" // load saved %ebp
"mov 8(%edx), %eax \n" // load saved %eip
"mov %eax, (%esp) \n" // store saved %eip to stack
"xor %eax, %eax \n" // clear return register
"inc %al \n" // increase to make 1, non-local return
"ret \n" // return
);
for (;;); // needed to silence compiler warning
}
Which just tries to perform operations on a completely random register (edx
in this case). The outcome is the expected: saving the pure random luck of
the compiler putting the right value in the random register above, there's
a crash.
2. Non-critical assessment.
The original commit message says "There is a small overhead introduced
(typically 1 machine instruction)". That machine instruction is a call
if a compiler doesn't perform tail optimization (happens regularly), and
it's 1 instruction only with the broken code shown above, fixing it
requires adding more. With inefficiencies already presented in the NLR
code, the overhead becomes "considerable" (several times more than 1%),
not "small".
The commit message also says "This eliminates duplicated code.". An
obvious way to eliminate duplication would be to factor out common code
to macros, not introduce overhead and breakage like above.
3. Faulty motivation.
All this started with a report of warnings/errors happening for a niche
compiler. It could have been solved in one the direct ways: a) fixing it
just for affected compiler(s); b) rewriting it in proper assembly (like
it was before BTW); c) by not doing anything at all, MICROPY_NLR_SETJMP
exists exactly to address minor-impact cases like thar (where a) or b) are
not applicable). Instead, a backwards "solution" was put forward, leading
to all the issues above.
The best action thus appears to be revert and rework, not trying to work
around what went haywire in the first place.
Damien George
liamkinne
Hemanth kumar
Ayke van Laethem
stijn
Peter D. Gray
Jim Mussared
Paul Sokolovsky