This can be used where the standard API calls for a list of pins, to check that they satisfy the requirements of the rp2pio state machine, e.g.,
```python
def __init__(self, pin_a, pin_b):
if not rp2pio.pins_are_sequential([pin_a, pin_b]):
raise ValueError("Pins must be sequential")
```
Presumably, switching it to generic hurt performance a bit.
I verified that the build-raspberry_pi_pico/boot2_padded_checksummed.S
built file has the same checksum as the old
bs2_default_padded_checksummed.S
.. all the necessary steps to transform it into a padded, checksummed
file are now done by the build system.
Since it is assigned by "?=", it _should_ be the case that individual
builds can override it.
I did not "test" this per se, but it gives the same content and checksum
(except for the identifying comment with a path) as #4302.
Two of the defaults have also changed in this commit:
- MICROPY_HW_RFCORE_BLE_LSE_SOURCE changed from 1 to 0, which configures
the LsSource to be LSE (needed due to errata 2.2.1).
- MICROPY_HW_RFCORE_BLE_VITERBI_MODE changed from 0 to 1, which enables
Viterbi mode, following all the ST examples.
Signed-off-by: Damien George <damien@micropython.org>
* Always clear the peripheral interrupt so we don't hang when full
* Store the ringbuf in the object so it gets collected when we're alive
* Make UART objects have a finaliser so they are deinit when their
memory is freed
* Copy bytes into the ringbuf from the FIFO after we read to ensure
the interrupt is enabled ASAP
* Copy bytes into the ringbuf from the FIFO before measuring our
rx available because the interrupt is based on a threshold (not
> 0). For example, a single byte won't trigger an interrupt.
This adds I2SOut and PDMIn support via PIO.
StateMachines can now:
* read and read while writing
* transfer in 1, 2 or 4 byte increments
* init pins based on expected defaults automatically
* be stopped and restarted
* rxfifo can be cleared and rxstalls detected (good for tracking when
the reading code isn't keeping up)
Fixes#4162
These ports already have uzlib enabled so this additional ubinascii.crc32
function only costs about 90 bytes of flash.
Signed-off-by: Damien George <damien@micropython.org>
Add LPUART1 as a standard UART. No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:
STM32WB: LPUART1 = UART(2)
STM32L0: LPUART1 = UART(6)
STM32L4: LPUART1 = UART(6)
STM32H7: LPUART1 = UART(9)
On all ports: LPUART1 = machine.UART('LP1')
LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.
Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
This commit fixes two issues on the esp32:
- it enables machine.soft_reset() to be called in main.py;
- it enables machine.reset_cause() to correctly identify a soft reset.
The former is useful in that it enables soft resets in applications that
are started at boot time. The support is patterned after the stm32 port.
This commit implements basic NVS support for the esp32. It follows the
pattern of the esp32.Partition class and exposes an NVS object per NVS
namespace. The initial support provided is only for signed 32-bit integers
and binary blobs. It's easy (albeit a bit tedious) to add support for
more types.
See discussions in: #4436, #4707, #6780
This enables -Os for compilation, but still keeps full assertion messages.
With IDF v4.2, -Os changes the GENERIC firmware size from 1512176 down to
1384640, and the GENERIC_SPIRAM firmware is now 1452320 which fits in the
allocated partition.
Signed-off-by: Damien George <damien@micropython.org>
So that mboot can be used to program encrypted/signed firmware to regions
of flash that are not the main application, eg that are the filesystem.
Signed-off-by: Damien George <damien@micropython.org>
Since the datasheet cast some doubt on the strength of the "rosc_hw->randombit",
I use the SHA256 hash function to create a high quality random seed
from random values of uncertain entropy, as well as to generate a sequence
of random values from that seed using SHA256 as a cryptographically-secure
random number generator.
In practice, it produces over 100kB/s of random data which does not
have any gross problems according to _PractRand_.
The default for these is to enable them, but they can now be disabled
individually by a board configuration.
Signed-off-by: Damien George <damien@micropython.org>
If a board defines USBD_VID then that will be used instead of the default.
And then the board must also define all USBD_PID_xxx values that it needs.
Signed-off-by: Damien George <damien@micropython.org>
The following simple usocket example throws an error EINVAL on connect
import usocket
s = usocket.socket()
s.connect(usocket.getaddrinfo('www.micropython.org', 80)[0][-1])
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: [Errno 22] EINVAL
Fixing the context parameter in calls of net_context_get_family() and
net_context_get_type(), the connect works fine.
Tested on a nucleo_h743zi board.
Refactors the zephyr build infrastructure to build MicroPython as a
cmake target, using the recently introduced core cmake rules.
This change makes it possible to build the zephyr port like most other
zephyr applications using west or cmake directly. It simplifies building
with extra cmake arguments, such as specifying an alternate conf file or
adding an Arduino shield. It also enables building the zephyr port
anywhere in the host file system, which will allow regressing across
multiple boards with the zephyr twister script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Disables frozen source modules in the zephyr port. They are deprecated
in the makefile rules and not implemented in the new cmake rules.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The underlying OS (the ESP-IDF) uses it's own internal errno codes and so
it's simpler and cleaner to use those rather than trying to convert
everything to the values defined in py/mperrno.h.
It's now replaced by cmake/idf.py. But a convenience Makefile is still
provided with traditional targets like "all" and "deploy".
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support for building the esp32 port with cmake, and in
particular it builds MicroPython as a component within the ESP-IDF. Using
cmake and the ESP-IDF build infrastructure makes it much easier to maintain
the port, especially with the various new ESP32 MCUs and their required
toolchains.
Signed-off-by: Damien George <damien@micropython.org>
This allows changing the baudrate of the UART without reinitialising it
(reinitialising can lead to spurious characters sent on the TX line).
Signed-off-by: Damien George <damien@micropython.org>
Also found a race condition between timer_disable and redraw, which
would happen if I debugger-paused inside common_hal_rgbmatrix_timer_disable
or put a delay or print inside it. That's what pausing inside reconstruct
fixes.
So that the "right timer" can be chosen, `timer_allocate` now gets the `self`
pointer. It's guaranteed at this point that the pin information is accurate,
so you can e.g., find a PWM unit related to the pins themselves.
This required touching each port to add the parameter even though it's
unused everywhere but raspberrypi.
On i.MX the SysTick IRQ cannot wake the CPU from a WFI so the CPU was
blocked on WFI waiting for USB data in mp_hal_stdin_rx_chr() even though it
had already arrived (because it may arrive just after calling the check
tud_cdc_available()). This commit fixes this problem by using SEV/WFE to
indicate that there has been a USB event.
The mp_hal_stdout_tx_strn() function is also fixed so that it doesn't
overflow the USB buffers.
Signed-off-by: Damien George <damien@micropython.org>
So that all MicroPython ports that use tinyusb use the same version. Also
requires fewer submodule checkouts when building rp2 along with other ports
that use tinyusb.
Signed-off-by: Damien George <damien@micropython.org>
START_SEC was changed in e0905e85a7.
Also, update the error message to mention how to format the partition at
the REPL, and make the total message shorter to save a bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
@Jerryneedell noticed that this problem affected strips short enough
to not use the DMA peripheral, thanks for the hot tip!
Instead of checking for background tasks after every byte transfer,
try up to 32 transfers before attending to background tasks.
This fixes the problem I was seeing on my 5-pixel circuit.
Closes#4135.
Add SMPS mode pin to Raspi Pico pins.c; see section "4.3. Using the ADC" of the Pico datasheet for discussion.
Driving this pin high forces the onboard regulator into a lower noise PWM mode.
This makes all the following work:
* normal microcontroller.reset()
* reset into safe mode or UF2 bootloader via microcontroller.on_next_reset()
* reset into UF2 bootloader via the "1200 baud trick"
The implementation of reset_cpu is from micropython.
In particular the firmware can now be built in a build directory that lives
outside the source tree, and the py/modarray.c file will still be found.
See issue #6837.
Signed-off-by: Damien George <damien@micropython.org>
The "word" referred to by BYTES_PER_WORD is actually the size of mp_obj_t
which is not always the same as the size of a pointer on the target
architecture. So rename this config value to better reflect what it
measures, and also prefix it with MP_.
For uses of BYTES_PER_WORD in setting the stack limit this has been
changed to sizeof(void *), because the stack usually grows with
machine-word sized values (eg an nlr_buf_t has many machine words in it).
Signed-off-by: Damien George <damien@micropython.org>
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise it resets the ADC peripheral each time a new ADC object is
constructed, which can reset other state that has already been set up.
See issue #6833.
Signed-off-by: Damien George <damien@micropython.org>
Default to just calling python since that is most commonly available: the
official installer or zipfiles from python.org, anaconda, nupkg all result
in python being available but not python3. In other words: the default
used so far is wrong. Note that os.name is 'posix' when running the python
version which comes with Cygwin or MSys2 so they are not affected by this.
However of all possible ways to get Python on Windows, only Cygwin provides
no python command so update the default way for running tests in the
README.
With mboot encrpytion and fsload enabled, the DEBUG build -O0 compiler
settings result in mboot no longer fitting in the 32k sector. This commit
changes this to -Og which also brings it into line with the regular stm32
build.
MCUs with device-only USB peripherals (eg L0, WB) do not implement (at
least not in the ST HAL) the HAL_PCD_DisconnectCallback event. So if a USB
cable is disconnected the USB driver does not deinitialise itself
(usbd_cdc_deinit is not called) and the CDC driver can stay in the
USBD_CDC_CONNECT_STATE_CONNECTED state. Then if the USB was attached to
the REPL, output can become very slow waiting in usbd_cdc_tx_always for
500ms for each character.
The disconnect event is not implemented on these MCUs but the suspend event
is. And in the situation where the USB cable is disconnected the suspend
event is raised because SOF packets are no longer received.
The issue of very slow output on these MCUs is fixed in this commit (really
worked around) by adding a check in usbd_cdc_tx_always to see if the USB
device state is suspended, and, if so, breaking out of the 500ms wait loop.
This should also help all MCUs for a real USB suspend.
A proper fix for MCUs with device-only USB would be to implement or somehow
synthesise the HAL_PCD_DisconnectCallback event.
See issue #6672.
Signed-off-by: Damien George <damien@micropython.org>
PIO state machines can make a conditional jump on the state of a pin: the
`JMP PIN` command. This requires the pin to be configured with
`sm_config_set_jmp_pin`, but until now we didn't have a way of doing that
in MicroPython.
This commit adds a new `jmp_pin=None` argument to `StateMachine`. If it is
not `None` then we try to interpret it as a Pin, and pass its value to
`sm_config_set_jmp_pin`.
Signed-off-by: Tim Radvan <tim@tjvr.org>
Add "make submodules" to commands when building for the first time.
Otherwise, on a first time build, the submodules have not been checked out
and a lot of `fatal error: nrfx.h: No such file or directory` errors are
printed.
It practically does the same as qstr_from_str and was only used in one
place, which should actually use the compile-time MP_QSTR_XXX form for
consistency; qstr_from_str is for runtime strings only.
Don't clear the IPCC channel flag until we've actually handled the incoming
data, or else the wireless firmware may clobber the IPCC buffer if more
data arrives. This requires masking the IRQ until the data is handled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a new port "rp2" which targets the new Raspberry Pi RP2040
microcontroller.
The build system uses pure cmake (with a small Makefile wrapper for
convenience). The USB driver is TinyUSB, and there is a machine module
with most of the standard classes implemented. Some examples are provided
in the examples/rp2/ directory.
Work done in collaboration with Graham Sanderson.
Signed-off-by: Damien George <damien@micropython.org>
It's enabled by default to retain the existing behaviour. A board can
disable this option if it manages mounting the filesystem itself, for
example in frozen code.
Signed-off-by: Damien George <damien@micropython.org>
Changes are:
- refactor to use new _create_element function
- support extended version of MOUNT element with block size
- support STATUS element
Signed-off-by: Damien George <damien@micropython.org>
This new element takes the form: (ELEM_TYPE_STATUS, 4, <address>). If this
element is present in the mboot command then mboot will store to the given
address the result of the filesystem firmware update process. The address
can for example be an RTC backup register.
Signed-off-by: Damien George <damien@micropython.org>
Instead it is now passed in as an optional parameter to the ELEM_MOUNT
element, with a compile-time configurable default.
Signed-off-by: Damien George <damien@micropython.org>
The superblock for littlefs is in block 0 and 1, but block 0 may be erased
or partially written, so block 1 must be checked if block 0 does not have a
valid littlefs superblock in it.
Prior to this commit, if block 0 did not contain a valid littlefs
superblock (but block 1 did) then the auto-detection would fail, mounting a
FAT filesystem would also fail, and the system would reformat the flash,
even though it may have contained a valid littlefs filesystem. This is now
fixed.
Signed-off-by: Damien George <damien@micropython.org>
Totally untested, change request based on change made in #2581.
It might be my first PR in CircuitPython core...
Maybe this should be confirmed by @jamesbowman
Those are the two boards that seems supported:
* Metro M4 Express
* Metro nRF52840 Express
The only Metro that this PR concern:
* Metro M4 AirLift Lite
Other Metro I found and are maybe not supported:
* Metro ESP32-S2
* Metro M0 Express
* Metro M7 1011
* Fix a typo in the Makefile that prevented the debug build to be actually
enabled when BTYPE=debug is used.
* Add a missing header in modmachine.c that is used when a debug build is
created.
This commit improves some FTP implementation details for better
compatibility with FTP clients:
* The PWD command now puts quotes around the directory name before
returning it. This fixes BBEdit’s FTP client, which performs a PWD after
each CWD and gets confused if the returned directory path is not
surrounded by quotes.
* The FEAT command is now allowed before logging in. This fixes the lftp
client, which send FEAT first and gets confused (tries to use TLS) if the
server responds with 332.
With MICROPY_FLOAT_IMPL_FLOAT the results of utime.time(), gmtime() and
localtime() change only every 129 seconds. As one consequence
tests/extmod/vfs_lfs_mtime.py will fail on a unix port with LFS support.
With this patch these functions only return floats if
MICROPY_FLOAT_IMPL_DOUBLE is used. Otherwise they return integers.
The RP2040 is new microcontroller from Raspberry Pi that features
two Cortex M0s and eight PIO state machines that are good for
crunching lots of data. It has 264k RAM and a built in UF2
bootloader too.
Datasheet: https://pico.raspberrypi.org/files/rp2040_datasheet.pdf
To match the definition of GENERATE_PACK_DFU, so a board can customise the
location/name of this file if needed.
Signed-off-by: Damien George <damien@micropython.org>
To have at least one board configured with MBOOT_ENABLE_PACKING, for CI
testing purposes and demonstration of the feature.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, the final piece of data in a compressed file may have
been lost when decompressing.
Signed-off-by: Damien George <damien@micropython.org>
As reported by @jerryneedell, this change was incorrect; the given
ESPTOOL_FLAGS caused `write_flash` to be repeated twice, which doesn't
work.
Closes#3981.
- prevent touch alarm initialization if not set
- fix wake_alarm is set to touch alarm on autoreload
- add ability to have multiple touch alarms in light sleep
Some ports need an extra operation to ensure that the main task is
awoken so that a queued background task will execute during an ongoing
light sleep.
This removes the need to enable supervisor ticks while I2SOut is operating.
Closes: #3952
Originally, I believed the implementation might be shared with AudioOut,
as on the ESP32 (non-S2) the I2S peripheral was also used to drive the DAC.
However, this is not the case on ESP32-S2 and appears it will not be
the case with the ESP32-S3 or -C3, to the extent that there's skeletal
support for either of them in esp-idf master branch.
However, it could still be shared by I2SIn or PDMIn (the latter being
hypothetically implemented as I2SIn + digital postprocessing like we did
in the atmel-sam port, to my understanding), so I moved it to
the common-hal folder.
.. otherwise, the background callback to load the I2S fifos does not get
run. (I'm not sure this is _correct_ behavior of sleep + background
tasks, but it is the current behavior)
There were _possibly_ problems where this routine was being entered
by direct call AND by background callback. Schedule the work here,
and it will be done almost immediately, without worry about interference.
I don't know if this is strictly necessary, but it doesn't hurt. Since
the I2S clock is being run all the time, we have to enter the background
task to fill the FIFO with zeros constantly anyway.
This can be useful so that e.g., on a Kaluga when programming via
the FTDI chip, you can override the variable to specify "--after=hard_reset"
to automatically return to running CircuitPython, choose a different
baud rate (921600 is about 2s faster than 460800), etc:
make BOARD=espressif_kaluga_1 ESPTOOL_FLAGS="-b 921600 --before=default_reset --after=hard_reset"
IO13 is for blue LED
IO14 is the correct pin header between IO18 and IO12
The silk is wrong (shows IO13), but hardware is correct as IO14, but IO14 was not included in pins.c
Silk will be updated on next PCB production run
(note that the before and after files both lack trailing newlines; this is
how the esp-idf do)
OPTIMIZATION_DEFAULT is -Og, which enables optimizations that do not
interfere with the debugger:
```
elseif(CONFIG_COMPILER_OPTIMIZATION_DEFAULT)
list(APPEND compile_options "-Og")
```
The XIP SPI flash on Fomu is slow, which results in certain operations
taking a long time. This becomes a problem for time-critical operations
such as USB.
Move various calls into RAM to improve performance.
This includes the call to __modsi3 and __udivsi3 which are used by the
supervisor handler to determine if periodic callbacks need to be run.
This finishes fixing #3841
Signed-off-by: Sean Cross <sean@xobs.io>
During an interrupt handler, interrupts are implicitly disabled. They
will be re-enabled when the interrupt handler returns.
Due to some changes that were made, varous calls will re-enable
interrupts after they're finished. Examples of this include calling
`CALLBACK_CRITICAL_END` and getting the number of ticks with
`port_get_raw_ticks()`.
This patch prevents this from happening by doing two things:
1. Use standard calls in `port_get_raw_ticks()` to disable and re-enable
interrupts, preventing nesting issues, and
2. Increase the nesting count inside `isr()`, reflecting the implicit
call that is made by hardware when an interrupt is handled
This helps to address #3841.
Signed-off-by: Sean Cross <sean@xobs.io>
* Better messaging when code is stopped by an auto-reload.
* Auto-reload works during sleeps on ESP32-S2. Ticks wake up the
main task each time.
* Made internal naming consistent. CamelCase Python names are NOT
separated by an underscore.
Very long ago, this was apparently not supported in esptool yet, at
least when operating over USB CDC. This now works just fine, and
our esp webtool relies on it as well. It makes flashing faster,
too.
