diff --git a/ports/stm32/boards/NUCLEO_H743ZI/board_init.c b/ports/stm32/boards/NUCLEO_H743ZI/board_init.c
new file mode 100644
index 0000000000..1a6006c280
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_H743ZI/board_init.c
@@ -0,0 +1,15 @@
+#include STM32_HAL_H
+
+void NUCLEO_H743ZI_board_early_init(void) {
+    GPIO_InitTypeDef GPIO_InitStructure;
+
+    __HAL_RCC_GPIOG_CLK_ENABLE();
+
+    // Turn off the USB switch
+    GPIO_InitStructure.Pin = GPIO_PIN_6;
+    GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
+    GPIO_InitStructure.Pull = GPIO_PULLDOWN;
+    GPIO_InitStructure.Speed = GPIO_SPEED_FREQ_LOW;
+    HAL_GPIO_Init(GPIOG, &GPIO_InitStructure);
+    HAL_GPIO_WritePin(GPIOG, GPIO_PIN_6, GPIO_PIN_RESET);
+}
diff --git a/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h
new file mode 100644
index 0000000000..4fe41e0a1b
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h
@@ -0,0 +1,57 @@
+#define MICROPY_HW_BOARD_NAME       "NUCLEO_H743ZI"
+#define MICROPY_HW_MCU_NAME         "STM32H743"
+
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_ADC       (0)
+#define MICROPY_HW_ENABLE_USB       (1)
+#define MICROPY_HW_HAS_SWITCH       (1)
+#define MICROPY_HW_HAS_FLASH        (1)
+
+#define MICROPY_BOARD_EARLY_INIT    NUCLEO_H743ZI_board_early_init
+void NUCLEO_H743ZI_board_early_init(void);
+
+// The board has an 8MHz HSE, the following gives 400MHz CPU speed
+#define MICROPY_HW_CLK_PLLM (4)
+#define MICROPY_HW_CLK_PLLN (400)
+#define MICROPY_HW_CLK_PLLP (2)
+#define MICROPY_HW_CLK_PLLQ (4)
+#define MICROPY_HW_CLK_PLLR (2)
+
+// 4 wait states
+#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_4
+
+// UART config
+#define MICROPY_HW_UART3_TX         (pin_D8)
+#define MICROPY_HW_UART3_RX         (pin_D9)
+#define MICROPY_HW_UART_REPL        PYB_UART_3
+#define MICROPY_HW_UART_REPL_BAUD   115200
+
+// I2C busses
+//#define MICROPY_HW_I2C1_SCL         (pin_B8)
+//#define MICROPY_HW_I2C1_SDA         (pin_B9)
+//#define MICROPY_HW_I2C3_SCL         (pin_H7)
+//#define MICROPY_HW_I2C3_SDA         (pin_H8)
+
+// SPI
+//#define MICROPY_HW_SPI2_NSS         (pin_I0)
+//#define MICROPY_HW_SPI2_SCK         (pin_I1)
+//#define MICROPY_HW_SPI2_MISO        (pin_B14)
+//#define MICROPY_HW_SPI2_MOSI        (pin_B15)
+
+// USRSW is pulled low. Pressing the button makes the input go high.
+#define MICROPY_HW_USRSW_PIN        (pin_C13)
+#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
+#define MICROPY_HW_USRSW_PRESSED    (1)
+
+// LEDs
+#define MICROPY_HW_LED1             (pin_B0)    // green
+#define MICROPY_HW_LED2             (pin_B7)    // blue
+#define MICROPY_HW_LED3             (pin_B14)   // red
+#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
+#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
+
+// USB config
+#define MICROPY_HW_USB_FS              (1)
+#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
+#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)
diff --git a/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk
new file mode 100644
index 0000000000..82b12cd2da
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.mk
@@ -0,0 +1,6 @@
+MCU_SERIES = h7
+CMSIS_MCU = STM32H743xx
+MICROPY_FLOAT_IMPL = double
+AF_FILE = boards/stm32h743_af.csv
+LD_FILE = boards/stm32h743.ld
+TEXT_ADDR = 0x08040000
diff --git a/ports/stm32/boards/NUCLEO_H743ZI/pins.csv b/ports/stm32/boards/NUCLEO_H743ZI/pins.csv
new file mode 100644
index 0000000000..b0d225368c
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_H743ZI/pins.csv
@@ -0,0 +1,59 @@
+A0,PA0
+A1,PF10
+A2,PF9
+A3,PF8
+A4,PF7
+A5,PF6
+D0,PC7
+D1,PC6
+D2,PG6
+D3,PB4
+D4,PG7
+D5,PA8
+D6,PH6
+D7,PI3
+D8,PI2
+D9,PA15
+D10,PI0
+D11,PB15
+D12,PB14
+D13,PI1
+D14,PB9
+D15,PB8
+LED1,PB0
+LED2,PB7
+LED3,PB14
+SW,PC13
+TP1,PH2
+TP2,PI8
+TP3,PH15
+AUDIO_INT,PD6
+AUDIO_SDA,PH8
+AUDIO_SCL,PH7
+EXT_SDA,PB9
+EXT_SCL,PB8
+EXT_RST,PG3
+SD_D0,PG9
+SD_D1,PG10
+SD_D2,PB3
+SD_D3,PB4
+SD_CK,PD6
+SD_CMD,PD7
+SD_SW,PI15
+LCD_BL_CTRL,PK3
+LCD_INT,PI13
+LCD_SDA,PH8
+LCD_SCL,PH7
+OTG_FS_POWER,PD5
+OTG_FS_OVER_CURRENT,PD4
+OTG_HS_OVER_CURRENT,PE3
+USB_VBUS,PJ12
+USB_ID,PA8
+USB_DM,PA11
+USB_DP,PA12
+UART1_TX,PA9
+UART1_RX,PA10
+UART5_TX,PC12
+UART5_RX,PD2
+UART3_TX,PD8
+UART3_RX,PD9
diff --git a/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h b/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h
new file mode 100644
index 0000000000..89421d30b7
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_H743ZI/stm32h7xx_hal_conf.h
@@ -0,0 +1,434 @@
+/**
+  ******************************************************************************
+  * @file    stm32h7xx_hal_conf_template.h
+  * @author  MCD Application Team
+  * @version V1.2.0
+  * @date   29-December-2017
+  * @brief   HAL configuration template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32h7xx_hal_conf.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32H7xx_HAL_CONF_H
+#define __STM32H7xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CEC_MODULE_ENABLED
+#define HAL_COMP_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_CRC_MODULE_ENABLED
+#define HAL_CRYP_MODULE_ENABLED
+#define HAL_DAC_MODULE_ENABLED
+#define HAL_DCMI_MODULE_ENABLED
+#define HAL_DFSDM_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_DMA2D_MODULE_ENABLED
+#define HAL_ETH_MODULE_ENABLED
+#define HAL_FDCAN_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_HASH_MODULE_ENABLED
+#define HAL_HCD_MODULE_ENABLED
+#define HAL_HRTIM_MODULE_ENABLED
+#define HAL_HSEM_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_I2S_MODULE_ENABLED
+#define HAL_IRDA_MODULE_ENABLED
+#define HAL_IWDG_MODULE_ENABLED
+#define HAL_JPEG_MODULE_ENABLED
+#define HAL_LPTIM_MODULE_ENABLED
+#define HAL_LTDC_MODULE_ENABLED
+#define HAL_MDIOS_MODULE_ENABLED
+#define HAL_MDMA_MODULE_ENABLED
+#define HAL_MMC_MODULE_ENABLED
+#define HAL_NAND_MODULE_ENABLED
+#define HAL_NOR_MODULE_ENABLED
+#define HAL_OPAMP_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_QSPI_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+#define HAL_SAI_MODULE_ENABLED
+#define HAL_SD_MODULE_ENABLED
+#define HAL_SDRAM_MODULE_ENABLED
+#define HAL_SMARTCARD_MODULE_ENABLED
+#define HAL_SMBUS_MODULE_ENABLED
+#define HAL_SPDIFRX_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_SRAM_MODULE_ENABLED
+#define HAL_SWPMI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+#define HAL_USART_MODULE_ENABLED
+#define HAL_WWDG_MODULE_ENABLED
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSE_VALUE)
+#define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal  oscillator (CSI) default value.
+  *        This value is the default CSI value after Reset.
+  */
+#if !defined  (CSI_VALUE)
+  #define CSI_VALUE    ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* CSI_VALUE */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE    ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+  #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief External clock source for I2S peripheral
+  *        This value is used by the I2S HAL module to compute the I2S clock source
+  *        frequency, this source is inserted directly through I2S_CKIN pad.
+  */
+#if !defined  (EXTERNAL_CLOCK_VALUE)
+  #define EXTERNAL_CLOCK_VALUE    12288000U /*!< Value of the External clock in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            ((uint32_t)0x0F) /*!< tick interrupt priority */
+#define  USE_RTOS                     0
+#define  USE_SD_TRANSCEIVER           1U               /*!< use uSD Transceiver */
+
+/* ########################### Ethernet Configuration ######################### */
+#define ETH_TX_DESC_CNT         4  /* number of Ethernet Tx DMA descriptors */
+#define ETH_RX_DESC_CNT         4  /* number of Ethernet Rx DMA descriptors */
+
+#define ETH_MAC_ADDR0    ((uint8_t)0x02)
+#define ETH_MAC_ADDR1    ((uint8_t)0x00)
+#define ETH_MAC_ADDR2    ((uint8_t)0x00)
+#define ETH_MAC_ADDR3    ((uint8_t)0x00)
+#define ETH_MAC_ADDR4    ((uint8_t)0x00)
+#define ETH_MAC_ADDR5    ((uint8_t)0x00)
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1 */
+
+/* ################## SPI peripheral configuration ########################## */
+/**
+  * @brief Used to activate CRC feature inside HAL SPI Driver
+  *        Activated   (1U): CRC code is compiled within HAL SPI driver
+  *        Deactivated (0U): CRC code excluded from HAL SPI driver
+  */
+
+#define USE_SPI_CRC                   1U
+
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+  #include "stm32h7xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+  #include "stm32h7xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+  #include "stm32h7xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+  #include "stm32h7xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+  #include "stm32h7xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+  #include "stm32h7xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+  #include "stm32h7xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+  #include "stm32h7xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+  #include "stm32h7xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+  #include "stm32h7xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_FDCAN_MODULE_ENABLED
+  #include "stm32h7xx_hal_fdcan.h"
+#endif /* HAL_FDCAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+  #include "stm32h7xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+  #include "stm32h7xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+  #include "stm32h7xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+  #include "stm32h7xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+  #include "stm32h7xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+  #include "stm32h7xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_HRTIM_MODULE_ENABLED
+  #include "stm32h7xx_hal_hrtim.h"
+#endif /* HAL_HRTIM_MODULE_ENABLED */
+
+#ifdef HAL_HSEM_MODULE_ENABLED
+  #include "stm32h7xx_hal_hsem.h"
+#endif /* HAL_HSEM_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+  #include "stm32h7xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+  #include "stm32h7xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+  #include "stm32h7xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32h7xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32h7xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32h7xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_JPEG_MODULE_ENABLED
+ #include "stm32h7xx_hal_jpeg.h"
+#endif /* HAL_JPEG_MODULE_ENABLED */
+
+#ifdef HAL_MDIOS_MODULE_ENABLED
+ #include "stm32h7xx_hal_mdios.h"
+#endif /* HAL_MDIOS_MODULE_ENABLED */
+
+#ifdef HAL_MDMA_MODULE_ENABLED
+ #include "stm32h7xx_hal_mdma.h"
+#endif /* HAL_MDMA_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+ #include "stm32h7xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+#include "stm32h7xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+#include "stm32h7xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_OPAMP_MODULE_ENABLED
+#include "stm32h7xx_hal_opamp.h"
+#endif /* HAL_OPAMP_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32h7xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32h7xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32h7xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32h7xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32h7xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32h7xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32h7xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32h7xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32h7xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_SWPMI_MODULE_ENABLED
+ #include "stm32h7xx_hal_swpmi.h"
+#endif /* HAL_SWPMI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32h7xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32h7xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32h7xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32h7xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32h7xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32h7xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32h7xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32h7xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32h7xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(uint8_t* file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32H7xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/